参数资料
| 型号： | ISL8101IRZ-T |
| 厂商： | Intersil |
| 文件页数： | 18/20页 |
| 文件大小： | 0K |
| 描述： | IC PWM CTRLR BUCK 2PHASE 24-QFN |
| 标准包装： | 6,000 |
| 应用： | 控制器，Intel VRM9，VRM10，AMD Hammer 应用 |
| 输入电压： | 4.6 V ~ 12 V |
| 输出数： | 1 |
| 输出电压： | 0.6 V ~ 2.3 V |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 24-VFQFN 裸露焊盘 |
| 供应商设备封装： | 24-QFN（4x4） |
| 包装： | 带卷 (TR) |
ISL8101
Component Selection Guidelines
Output Capacitor Selection
single channel’s ripple current is approximated by using
Equation 25.
I L , P-P = -------------------------------- × ----------------
The output capacitor is selected to meet both the dynamic
load requirements and the voltage ripple requirements. The
V IN – V OUT V OUT
F SW ? L V IN
(EQ. 25)
load transient a microprocessor impresses is characterized
by high slew rate (di/dt) current demands. In general,
multiple high quality capacitors of different size and dielectric
are paralleled to meet the design constraints.
Should the load be characterized by high slew rates, attention
should be particularly paid to the selection and placement of
The current from multiple channels tend to cancel each other
and reduce the total ripple current. The total output ripple
current can be determined using the curve in Figure 11; it
provides the total ripple current as a function of duty cycle
and number of active channels, normalized to the parameter
K NORM at zero duty cycle (see Equation 26).
L ? F SW
high-frequency decoupling capacitors (MLCCs, typically
multi-layer ceramic capacitors). High frequency capacitors
supply the initially transient current and slow the load
V OUT
K NORM = --------------------
(EQ. 26)
rate-of-change seen by the bulk capacitors. The bulk filter
capacitor values are generally determined by the ESR
(effective series resistance) and capacitance requirements.
High frequency decoupling capacitors should be placed as
close to the power pins of the load, or for that reason, to any
decoupling target they are meant for, as physically possible.
where L is the channel inductor value.
Find the intersection of the active channel curve and duty
cycle for your particular application. The resulting ripple
current multiplier from the y-axis is then multiplied by the
normalization factor, K NORM , to determine the total output
ripple current for the given application (see Equation 27).
Attention should be paid as not to add inductance in the
circuit board wiring that could cancel the usefulness of these
low inductance components. Consult with the manufacturer
of the load on specific decoupling requirements.
Use only specialized low-ESR capacitors intended for
switching-regulator applications for the bulk capacitors. The
bulk capacitor ’s ESR determines the output ripple voltage
and the initial voltage drop following a high slew-rate
transient’s edge. In most cases, multiple capacitors of small
case size perform better than a single large case capacitor.
Bulk capacitor choices include aluminum electrolytic, OS-Con,
Tantalum and even ceramic dielectrics. An aluminum
electrolytic capacitor’s ESR value is related to the case size
Δ I TOTAL = K NORM ? K CM
1.0
0.8
0.6
0.4
0.2
(EQ. 27)
with lower ESR available in larger case sizes. However, the
equivalent series inductance (ESL) of these capacitors
increases with case size and can reduce the usefulness of the
0
0
0.1
0.2 0.3
DUTY CYCLE (V O /V IN )
0.4
0.5
capacitor to high slew-rate transient loading. Unfortunately,
ESL is not a specified parameter. Consult the capacitor
manufacturer and/or measure the capacitor’s impedance with
frequency to help select a suitable component.
Output Inductor Selection
One of the parameters limiting the converter ’s response to a
load transient is the time required to change the inductor
current. In a multiphase converter, small inductors reduce
the response time with less impact to the total output ripple
current (as compared to single-phase converters).
The output inductor of each power channel controls the
ripple current. The control IC is stable for channel ripple
current (peak-to-peak) up to twice the average current. A
18
FIGURE 11. RIPPLE CURRENT vs DUTY CYCLE
FN9223.1
July 28, 2008
相关PDF资料 |
PDF描述 |
|---|---|
| MIC39501-2.5WU | IC REG LDO 2.5V 5A TO-263-5 |
| ISL6324CRZ-T | IC HYBRID CTRLR PWM DUAL 48-QFN |
| LT1963AEFE-3.3#PBF | IC REG LDO 3.3V 1.5A 16TSSOP |
| HIP6004DCRZ-T | IC CTRLR PWM VOLTAGE MON 20-QFN |
| LT1963AEFE-1.8#PBF | IC REG LDO 1.8V 1.5A 16TSSOP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ISL8102 | 制造商:INTERSIL 制造商全称:Intersil Corporation 功能描述:Two-Phase Buck PWM Controller with High Current Integrated MOSFET Drivers |
| ISL8102CRZ | 功能描述:IC REG CTRLR BUCK PWM VM 32-QFN RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 切换控制器 系列:- 标准包装:2,500 系列:- PWM 型:电流模式 输出数:1 频率 - 最大:500kHz 占空比:100% 电源电压:8.2 V ~ 30 V 降压:无 升压:无 回扫:是 反相:无 倍增器:无 除法器:无 Cuk:无 隔离:是 工作温度:0°C ~ 70°C 封装/外壳:8-DIP（0.300"，7.62mm） 包装:管件 产品目录页面:1316 (CN2011-ZH PDF) |
| ISL8102CRZ-T | 功能描述:IC REG CTRLR BUCK PWM VM 32-QFN RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 切换控制器 系列:- 标准包装:4,000 系列:- PWM 型:电压模式 输出数:1 频率 - 最大:1.5MHz 占空比:66.7% 电源电压:4.75 V ~ 5.25 V 降压:是 升压:无 回扫:无 反相:无 倍增器:无 除法器:无 Cuk:无 隔离:无 工作温度:-40°C ~ 85°C 封装/外壳:40-VFQFN 裸露焊盘 包装:带卷 (TR) |
| ISL8102EVAL1 | 功能描述:EVAL BOARD 1 FOR ISL8102 RoHS:否 类别:编程器，开发系统 >> 评估板 - DC/DC 与 AC/DC（离线）SMPS 系列:* 标准包装:1 系列:- 主要目的:DC/DC，步降 输出及类型:1，非隔离 功率 - 输出:- 输出电压:3.3V 电流 - 输出:3A 输入电压:4.5 V ~ 28 V 稳压器拓扑结构:降压 频率 - 开关:250kHz 板类型:完全填充 已供物品:板 已用 IC / 零件:L7981 其它名称:497-12113STEVAL-ISA094V1-ND |
| ISL8102IRZ | 功能描述:IC REG CTRLR BUCK PWM VM 32-QFN RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 切换控制器 系列:- 标准包装:2,500 系列:- PWM 型:电流模式 输出数:1 频率 - 最大:500kHz 占空比:100% 电源电压:8.2 V ~ 30 V 降压:无 升压:无 回扫:是 反相:无 倍增器:无 除法器:无 Cuk:无 隔离:是 工作温度:0°C ~ 70°C 封装/外壳:8-DIP（0.300"，7.62mm） 包装:管件 产品目录页面:1316 (CN2011-ZH PDF) |
发布紧急采购，3分钟左右您将得到回复。