- 您现在的位置：买卖IC网 > PDF目录17325 > ISL8118EVAL1Z (Intersil)EVALUATION BOARD FOR ISL8118 PDF资料下载
参数资料
| 型号： | ISL8118EVAL1Z |
| 厂商： | Intersil |
| 文件页数： | 11/20页 |
| 文件大小： | 0K |
| 描述： | EVALUATION BOARD FOR ISL8118 |
| 标准包装： | 1 |
| 主要目的： | DC/DC，步降 |
| 输出及类型： | 1，非隔离 |
| 输出电压： | 1.8V |
| 电流 - 输出： | 25A |
| 输入电压： | 4.5 ~ 20 V |
| 稳压器拓扑结构： | 降压 |
| 频率 - 开关： | 300kHz |
| 板类型： | 完全填充 |
| 已供物品： | 板 |
| 已用 IC / 零件： | ISL8118 |
ISL8118
OV/UV/PGOOD comparators. The VDIFF pin should be
connected to the FB pin by a standard feedback network. In
VIN
the event that the remote sense buffer is disabled, the VDIFF
pin should be connected to VOUT by a resistor divider along
R UP
V REF
Sys_Enable
with FB’s compensation network. An RC filter should be used
R UP = --------------------------
R DOWN = ---------------------------------------------------------
if VDIFF is to be connected directly to FB instead of to VOUT
through a separate resistor divider network.
GND (Bottom Side Pad, Analog Ground)
Signal ground for the IC. All voltage levels are measured
with respect to this pin. This pin should not be left floating.
Functional Description
Initialization
The ISL8118 automatically initializes upon receipt of power
without requiring any special sequencing of the input
supplies. The Power-On Reset (POR) function continually
monitors the input supply voltages (PVCC,VFF, VCC) and
the voltage at the EN pin. Assuming the EN pin is pulled to
above ~0.50V, the POR function initiates soft-start operation
after all input supplies exceed their POR thresholds.
HIGH = ABOVE POR; LOW = BELOW POR
VCC POR
R DOWN
I EN_HYS = 10μA
V EN_HYS
I EN_HYS
R UP ? V EN_REF
V EN_FTH – V EN_REF
V EN_FTH = V EN_RTH – V EN_HYS
FIGURE 2. ENABLE POR CIRCUIT
Soft-start
The POR function activates the internal 38μA OTA which
begins charging the external capacitor (C SS ) on the SS pin to a
target voltage of VCC. The ISL8118’s soft-start logic continues
to charge the SS pin until the voltage on COMP exceeds the
bottom of the oscillator ramp, at which point, the driver outputs
are enabled, with the bottom side MOSFET first being held low
for 200ns to provide for charging of the bootstrap capacitor.
Once the driver outputs are enabled, the OTA’s target voltage is
VFF POR
PVCC POR
EN POR
AND
SOFT-START
then changed to the margined (if margining is being used)
reference voltage (V REF_MARG ), and the SS pin is ramped up
or down accordingly. This method reduces start-up surge
currents due to a pre-charged output by inhibiting regulator
FIGURE 1. SOFT-START INITIALIZATION LOGIC
With all input supplies above their POR thresholds, driving
the EN pin above 0.50V initiates a soft-start cycle. In addition
to normal TTL logic, the enable pin can be used as a voltage
monitor with programmable hysteresis through the use of the
internal 10mA sink current and an external resistor divider.
This feature is especially designed for applications that have
input rails greater than a 3.3V and require specific input rail
POR and Hysteresis levels for better undervoltage
protection. Consider for a 12V application choosing
RUP = 100k Ω and RDOWN = 5.76k Ω there by setting the
rising threshold (VEN_RTH) to 10V and the falling threshold
(VEN_FTH) to 9V, for 1V of hysteresis (VEN_HYS). Care
should be taken to prevent the voltage at the EN pin from
exceeding VCC when using the programmable UVLO
functionality.
11
switching until the control loop enters its linear region. By
ramping the positive input of the error amplifier to VCC and
then to V REF_MARG , it is even possible to mitigate surge
currents from outputs that are pre-charged above the set output
voltage. As the SS pin connects directly to the non-inverting
input of the Error Amplifier, noise on this pin should be kept to a
minimum through careful routing and part placement. To
prevent noise injection into the error amplifier, the SS capacitor
should be located within 150 mils of the SS and GND pins.
Soft-start is declared done when the drivers have been enabled
and the SS pin is within ±3mV of V REF_MARG .
Power Good
The power good comparator references the voltage on the
soft-start pin to prevent accidental tripping during margining.
The trip points are shown on Figure 3. Additionally, power
good will not be asserted until after the completion of the
soft-start cycle. A 0.1μF capacitor at the PGDLY pin will add
an additional ~7.1ms delay to the assertion of power good.
PGDLY does not delay the deassertion of power good.
FN6325.2
November 29, 2012
相关PDF资料 |
PDF描述 |
|---|---|
| A9CCG-1604F | FLEX CABLE - AFG16G/AF16/AFG16G |
| GEM10DRTI-S13 | CONN EDGECARD 20POS .156 EXTEND |
| GEM10DRKI-S13 | CONN EDGECARD 20POS .156 EXTEND |
| ISL8502EVAL1Z | EVALUATION BOARD FOR ISL8502 |
| GEM22DRYI | CONN EDGECARD 44POS DIP .156 SLD |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ISL8118IRZ | 功能描述:IC REG CTRLR BUCK PWM VM 28-QFN RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 切换控制器 系列:- 标准包装:75 系列:- PWM 型:电流模式 输出数:1 频率 - 最大:1MHz 占空比:81% 电源电压:4.3 V ~ 13.5 V 降压:是 升压:是 回扫:是 反相:无 倍增器:无 除法器:无 Cuk:无 隔离:无 工作温度:0°C ~ 70°C 封装/外壳:8-SOIC（0.154"，3.90mm 宽） 包装:管件 产品目录页面:1051 (CN2011-ZH PDF) 其它名称:296-2543-5 |
| ISL8118IRZ-T | 功能描述:IC REG CTRLR BUCK PWM VM 28-QFN RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 切换控制器 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,500 系列:- PWM 型:电流模式 输出数:1 频率 - 最大:275kHz 占空比:50% 电源电压:18 V ~ 110 V 降压:无 升压:无 回扫:无 反相:无 倍增器:无 除法器:无 Cuk:无 隔离:是 工作温度:-40°C ~ 85°C 封装/外壳:8-SOIC（0.154"，3.90mm 宽） 包装:带卷 (TR) |
| ISL8120 | 制造商:INTERSIL 制造商全称:Intersil Corporation 功能描述:Dual/n-Phase Buck PWM Controller with Integrated Drivers |
| ISL8120CRZ | 功能描述:IC REG CTRLR BUCK PWM VM 32-QFN RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 切换控制器 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,500 系列:- PWM 型:电流模式 输出数:1 频率 - 最大:275kHz 占空比:50% 电源电压:18 V ~ 110 V 降压:无 升压:无 回扫:无 反相:无 倍增器:无 除法器:无 Cuk:无 隔离:是 工作温度:-40°C ~ 85°C 封装/外壳:8-SOIC（0.154"，3.90mm 宽） 包装:带卷 (TR) |
| ISL8120CRZ-T | 功能描述:IC REG CTRLR BUCK PWM VM 32-QFN RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 切换控制器 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,500 系列:- PWM 型:电流模式 输出数:1 频率 - 最大:275kHz 占空比:50% 电源电压:18 V ~ 110 V 降压:无 升压:无 回扫:无 反相:无 倍增器:无 除法器:无 Cuk:无 隔离:是 工作温度:-40°C ~ 85°C 封装/外壳:8-SOIC（0.154"，3.90mm 宽） 包装:带卷 (TR) |
发布紧急采购，3分钟左右您将得到回复。