参数资料
| 型号： | ISL9105IRZ-T |
| 厂商： | Intersil |
| 文件页数： | 8/11页 |
| 文件大小： | 0K |
| 描述： | IC REG BUCK SYNC ADJ 0.6A 8DFN |
| 产品培训模块： | Solutions for Industrial Control Applications |
| 标准包装： | 1 |
| 类型： | 降压（降压） |
| 输出类型： | 可调式 |
| 输出数： | 1 |
| 输出电压： | 0.8 V ~ 5.5 V |
| 输入电压： | 2.7 V ~ 5.5 V |
| PWM 型： | 电流模式 |
| 频率 - 开关： | 1.6MHz |
| 电流 - 输出： | 600mA |
| 同步整流器： | 是 |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 8-VFDFN 裸露焊盘 |
| 包装： | 标准包装 |
| 供应商设备封装： | 8-DFN（2x3） |
| 产品目录页面： | 1244 (CN2011-ZH PDF) |
| 其它名称： | ISL9105IRZ-TDKR |
ISL9105
discussed separately in the “Soft-Start-Up” on page 9. The
error amplifier is a transconductance amplifier, which
converts the voltage error signal to a current output. The
voltage loop is internally compensated by a RC network. The
maximum EAMP voltage output is precisely clamped to the
bandgap voltage (1.172V).
V EAMP
V CSA1
DUTY
CYCLE
I L
V OUT
FIGURE 15. PWM OPERATION WAVEFORMS
SKIP Mode
The ISL9105 enters a pulse-skipping mode at light load to
minimize the switching loss by reducing the effective
switching frequency. Figure 16 illustrates the skip-mode
operation. A zero-cross sensing circuit (as shown in
Figure 15) monitors the N-Channel MOSFET current for zero
crossing. When the N-Channel MOSFET current is detected
crossing zero for 8 consecutive cycles, the regulator enters
the skip mode. During the 8 consecutive cycles, the inductor
current is allowed to be negative. The internal counter is
reset to zero when the sensed N-Channel MOSFET current
does not cross zero in any cycle within the 8 consecutive
cycles.
Once ISL9105 enters SKIP mode, the pulse modulation
starts being controlled by the SKIP comparator shown in
Figure 15. Each pulse cycle is still synchronized by the PWM
clock. The P-Channel MOSFET is turned on at the rising
edge of the clock and turned off when its current reaches
20% of the peak current limit. As the average inductor
current in each cycle is higher than the average current of
CLOCK
8 CYCLES
I L
the load, the output voltage rises cycle over cycle. When the
output voltage reaches 1.5% above the nominal voltage, the
P-Channel MOSFET is turned off immediately and the
inductor current is fully discharged to zero and remains zero.
The output voltage reduces gradually due to the load current
discharging the output capacitor. When the output voltage
drops to the nominal voltage, the P-Channel MOSFET will
be turned on again, repeating the previous operations.
The regulator resumes PWM mode operation when the
output voltage drops 1.5% below the nominal voltage.
Enable
The enable (EN) input allows user to control the turn-on and
turn-off of the regulator for purposes, such as power-up
sequencing. When the regulator is enabled, there is a
typically a 600μs delay for waking up the internal reference
circuit, then the soft start-up begins. When the regulator is
disabled, the P-MOSFET is turned off immediately and the
output capacitor is discharged.
POR Signal
The ISL9105 offers a Power-On Reset (POR) signal. When
the output voltage is not within a power-good window, the
POR pin outputs an open-drain low signal (Figure 15), which
can be used to reset the microprocessor. When the output
voltage is within a power-good window, a power-good signal
is issued to turn off the open-drain POR pin. The rising edge
of the POR output is delayed by 216ms (typical) from the
time the power-good signal is issued.
Mode Selection
MODE pin is provided on ISL9105 to select the operation
mode. When it is driven to logic low or shorted to ground, the
regulator operates in the forced PWM mode. The forced
PWM mode remains the fixed PWM frequency (typically
1.6MHz) at all load conditions.
When the MODE pin is driven to logic high or connected to
input voltage V IN , the regulator operates in either SKIP
mode or fixed PWM mode depending upon the load
condition.
CURRENT LIMIT
LOAD CURRENT
0
NOMINAL + 1.5%
V OUT
NOMINAL
FIGURE 16. SKIP MODE OPERATION WAVEFORMS
8
FN6415.2
March 28, 2008
相关PDF资料 |
PDF描述 |
|---|---|
| ISL9106IRZ | IC REG BUCK SYNC ADJ 1.2A 10DFN |
| ISL9107IRZ-T | IC REG BUCK SYNC ADJ 1.5A 8DFN |
| ISL9109IRZ-T | IC REG BUCK SYNC ADJ 1.5A 8DFN |
| ISL9110AIITNZ-T | IC VOLTAGE REGULATOR |
| ISL9111EH30Z-T | IC VOLTAGE REGULATOR |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ISL9105IRZ-TS2715 | 制造商:Intersil Corporation 功能描述:S SPEC FOR TRACKING BROADCOM BUSINESS ONLY-SOLD THRU DISTI - Tape and Reel |
| ISL9106 | 制造商:INTERSIL 制造商全称:Intersil Corporation 功能描述:1.2A 1.6MHz Low Quiescent Current High Efficiency Synchronous Buck Regulator |
| ISL9106EVAL1Z | 功能描述:电源管理IC开发工具 ISL9106 EVALUATION BOARD 1 - RoHS COMPLIANT - DFN RoHS:否 制造商:Maxim Integrated 产品:Evaluation Kits 类型:Battery Management 工具用于评估:MAX17710GB 输入电压: 输出电压:1.8 V |
| ISL9106IRZ | 功能描述:IC REG BUCK SYNC ADJ 1.2A 10DFN RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 标准包装:50 系列:- 类型:升压（升压） 输出类型:可调式 输出数:1 输出电压:5 V ~ 25 V 输入电压:2.3 V ~ 5.5 V PWM 型:电流模式 频率 - 开关:600kHz，1.2MHz 电流 - 输出:1A 同步整流器:无 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:8-TSSOP，8-MSOP（0.118"，3.00mm 宽） 包装:管件 供应商设备封装:8-MSOP |
| ISL9106IRZ-T | 功能描述:IC REG BUCK SYNC ADJ 1.2A 10DFN RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 标准包装:1,000 系列:- 类型:降压（降压） 输出类型:可调式 输出数:1 输出电压:0.6 V ~ 4.5 V 输入电压:3 V ~ 5.5 V PWM 型:电流模式 频率 - 开关:3MHz 电流 - 输出:1.5A 同步整流器:无 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:6-WDFN 裸露焊盘 包装:带卷 (TR) 供应商设备封装:6-LLP-EP（3x3） 产品目录页面:1300 (CN2011-ZH PDF) 其它名称:LM2831ZSDLM2831ZSDTR |
发布紧急采购，3分钟左右您将得到回复。