参数资料
| 型号： | ISL9106IRZ |
| 厂商： | Intersil |
| 文件页数： | 10/13页 |
| 文件大小： | 0K |
| 描述： | IC REG BUCK SYNC ADJ 1.2A 10DFN |
| 标准包装： | 100 |
| 类型： | 降压（降压） |
| 输出类型： | 可调式 |
| 输出数： | 1 |
| 输出电压： | 0.8 V ~ 5.5 V |
| 输入电压： | 2.7 V ~ 5.5 V |
| PWM 型： | 电流模式 |
| 频率 - 开关： | 1.6MHz |
| 电流 - 输出： | 1.2A |
| 同步整流器： | 是 |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 10-VFDFN 裸露焊盘 |
| 包装： | 管件 |
| 供应商设备封装： | 10-DFN（3x3） |
ISL9106
Once ISL9106 enters the skip mode, the pulse modulation
v EAMP
v CSA
d
i L
v OUT
FIGURE 25. PWM OPERATION WAVEFORMS
The output voltage is regulated by controlling the reference
voltage to the current loop. The bandgap circuit outputs a
0.8V reference voltage to the voltage control loop. The
feedback signal comes from the FB pin. The soft-start block
only affects the operation during the start-up and will be
discussed separately in “Soft-Start-Up” on page 11. The
EAMP is a transconductance amplifier, which converts the
voltage error signal to a current output. The voltage loop is
internally compensated by a RC network. The maximum
EAMP voltage output is precisely clamped to the bandgap
voltage.
Skip Mode
With the MODE pin connected to logic high, ISL9106 enters
a pulse-skipping mode at light load to minimize the switching
loss by reducing the switching frequency. Figure 26
illustrates the skip mode operation. A zero-cross sensing
circuit (as shown in Figure 24) monitors the N-Channel
MOSFET current for zero crossing. When it is detected to
cross zero for 8 consecutive cycles, the regulator enters the
skip mode. During the 8 consecutive cycles, the inductor
current could be negative. The counter is reset to zero when
the sensed N-Channel MOSFET current does not cross zero
during any cycle within the 8 consecutive cycles.
starts being controlled by the SKIP comparator shown in
Figure 24. Each pulse cycle is still synchronized by the PWM
clock. The P-Channel MOSFET is turned on at the rising
edge of clock and turned off when its current reaches 20% of
the peak current limit. As the average inductor current in
each cycle is higher than the average current of the load, the
output voltage rises cycle over cycle. When the output
voltage reaches 1.5% above its nominal voltage, the P-
Channel MOSFET is turned off immediately and the inductor
current is fully discharged to zero and stays at zero. The
output voltage reduces gradually due to the load current
discharging the output capacitor. When the output voltage
drops to the nominal voltage, the P-Channel MOSFET will
be turned on again, repeating the previous operations.
The regulator resumes normal PWM mode operation when
the output voltage is sensed to drop below 1.5% of its
nominal voltage value.
Enable
The enable (EN) pin allows user to enable or disable the
converter for purposes such as power-up sequencing. With
EN pin pulled to high, the converter is enabled and the
internal reference circuit wakes up first and then the soft
start-up begins. When EN pin is pulled to logic low, the
converter is disabled, the P-Channel MOSFET is turned off
immediately and the output capacitor is discharged through
internal discharge path.
Power Good
The ISL9106 offers a power-good (PG) signal. When the
output voltage is not within the power-good window, the PG
pin outputs an open-drain low signal. When the output
voltage is within the power-good window, an internal power-
good signal is issued to turn off the open-drain MOSFET so
that PG pin can be externally pulled to high. The rising edge
of the PG output is delayed by 215ms (typical) from the time
the power-good signal is issued.
8 CYCLES
CLOCK
20% PEAK CURRENT LIMIT
I L
0
1.015*V OUT_NOMINAL
V OUT
V OUT_NOMINAL
FIGURE 26. SKIP MODE OPERATION WAVEFORMS
10
FN6509.0
June 29, 2007
相关PDF资料 |
PDF描述 |
|---|---|
| ISL9107IRZ-T | IC REG BUCK SYNC ADJ 1.5A 8DFN |
| ISL9109IRZ-T | IC REG BUCK SYNC ADJ 1.5A 8DFN |
| ISL9110AIITNZ-T | IC VOLTAGE REGULATOR |
| ISL9111EH30Z-T | IC VOLTAGE REGULATOR |
| ISL9112IRT7Z-T7A | IC REG BUCK BOOST SYNC 5V 12TDFN |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ISL9106IRZ-T | 功能描述:IC REG BUCK SYNC ADJ 1.2A 10DFN RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 标准包装:1,000 系列:- 类型:降压（降压） 输出类型:可调式 输出数:1 输出电压:0.6 V ~ 4.5 V 输入电压:3 V ~ 5.5 V PWM 型:电流模式 频率 - 开关:3MHz 电流 - 输出:1.5A 同步整流器:无 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:6-WDFN 裸露焊盘 包装:带卷 (TR) 供应商设备封装:6-LLP-EP（3x3） 产品目录页面:1300 (CN2011-ZH PDF) 其它名称:LM2831ZSDLM2831ZSDTR |
| ISL9106IRZ-TS2708 | 制造商:Intersil Corporation 功能描述:ITSISL9106IRZ-TS2708 INTELION / ATHEROS |
| ISL9107 | 制造商:INTERSIL 制造商全称:Intersil Corporation 功能描述:1.5A 1.6MHz Low Quiescent Current High Efficiency Synchronous Buck Regulator |
| ISL9107EVAL1Z | 功能描述:电源管理IC开发工具 ISL9107 EVALUATION BOARD 1 - RoHS COMPLIANT - DFN RoHS:否 制造商:Maxim Integrated 产品:Evaluation Kits 类型:Battery Management 工具用于评估:MAX17710GB 输入电压: 输出电压:1.8 V |
| ISL9107IRZ-T | 功能描述:直流/直流开关转换器 W/ANNEAL LW IQ BUCK REGW/INTEGRATEDFET RoHS:否 制造商:STMicroelectronics 最大输入电压:4.5 V 开关频率:1.5 MHz 输出电压:4.6 V 输出电流:250 mA 输出端数量:2 最大工作温度:+ 85 C 安装风格:SMD/SMT |
发布紧急采购，3分钟左右您将得到回复。