参数资料
| 型号： | ISL9106IRZ |
| 厂商： | Intersil |
| 文件页数： | 11/13页 |
| 文件大小： | 0K |
| 描述： | IC REG BUCK SYNC ADJ 1.2A 10DFN |
| 标准包装： | 100 |
| 类型： | 降压（降压） |
| 输出类型： | 可调式 |
| 输出数： | 1 |
| 输出电压： | 0.8 V ~ 5.5 V |
| 输入电压： | 2.7 V ~ 5.5 V |
| PWM 型： | 电流模式 |
| 频率 - 开关： | 1.6MHz |
| 电流 - 输出： | 1.2A |
| 同步整流器： | 是 |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 10-VFDFN 裸露焊盘 |
| 包装： | 管件 |
| 供应商设备封装： | 10-DFN（3x3） |
ISL9106
Mode Selection
The MODE pin is provided on ISL9106 to select the
operation mode. When it is driven to logic low or ground, the
regulator operates in forced PWM mode. Under forced PWM
mode, the device remains at the fixed PWM operation
(typical at 1.6MHz), regardless of if the load current is high
or low.
When the MODE pin is driven to logic high or connected to
input voltage V IN , the regulator operates in either SKIP
mode or fixed PWM mode depending on the different load
conditions.
RSI Signal
The RSI signal is an input signal, which can reset the PG
signal. As shown in Figure 24, the power-good signal is
gated by the RSI signal. When the RSI is high, the PG signal
remains low, regardless of the output voltage condition.
Overcurrent Protection
The overcurrent protection is provided on ISL9106 when
over load condition happens. It is realized by monitoring the
CSA output with the OCP comparator, as shown in Figure 24.
maintain the output voltage, the P-Channel MOSFET is
completely turned on (100% duty cycle). The dropout
voltage under such condition is the product of the load
current and the ON-resistance of the P-Channel MOSFET.
Minimum required input voltage V IN under this condition is
the sum of output voltage plus the voltage drop cross the
inductor and the P-Channel MOSFET switch.
Thermal Shut Down
The ISL9106 provides built-in thermal protection function.
The thermal shutdown threshold temperature is typical
+150°C with typical +25°C hysteresis. When the internal
temperature is sensed to reach +150°C, the regulator is
completely shut down and as the temperature is sensed to
drop to +125°C (typical), the ISL9106 resumes operation
starting from the soft-start-up.
Applications Information
Inductor and Output Capacitor Selection
To achieve better steady state and transient response,
ISL9106 typically uses a 2.2μH inductor. The peak-to-peak
inductor current ripple can be expressed as follows:
V O ? ? 1 – --------- ?
L ? f S
When the current at P-Channel MOSFET is sensed to reach
the current limit, the OCP comparator is trigged to turn off
the P-Channel MOSFET immediately.
Short-Circuit Protection
? V O ?
? V IN ?
Δ I = ---------------------------------------
(EQ. 1)
ISL9106 has a Short-Circuit Protection (SCP) comparator,
which monitors the FB pin voltage for output short-circuit
protection. When the FB voltage is lower than 0.2V, the SCP
comparator forces the PWM oscillator frequency to drop to
1/3 of its normal operation frequency.
Undervoltage Lockout (UVLO)
When the input voltage is below the Undervoltage Lock Out
(UVLO) threshold, ISL9106 is disabled.
Soft-Start-Up
The soft-start-up eliminates the inrush current during the
circuit start-up. The soft-start block outputs a ramp reference
to both the voltage loop and the current loop. The two ramps
limit the inductor current rising speed as well as the output
voltage speed so that the output voltage rises in a controlled
fashion. At the very beginning of the start-up, the output
voltage is less than 0.2V; hence the PWM operating
frequency is 1/3 of the normal frequency.
Power MOSFETs
The power MOSFETs are optimized to achieve better
efficiency. The ON-resistance for the P-Channel MOSFET is
typically160m Ω and the typical ON-resistance for the
N-Channel MOSFET is 150m Ω .
Low Dropout Operation
The ISL9106 features low dropout operation to maximize the
battery life. When the input voltage drops to a level that
ISL9106 can no longer operate under switching regulation to
11
In Equation 1, usually the typical values can be used but to
have a more conservative estimation, the inductance should
consider the value with worst case tolerance; and for
switching frequency f S , the minimum f S from the “Eletrical
Specifications” table on page 2 can be used.
To select the inductor, its saturation current rating should be
at least higher than the sum of the maximum output current
and half of the delta calculated from Equation 1. Another
more conservative approach is to select the inductor with the
current rating higher than the P-Channel MOSFET peak
current limit.
Another consideration is the inductor DC resistance since it
directly affects the efficiency of the converter. Ideally, the
inductor with the lower DC resistance should be considered
to achieve higher efficiency.
Inductor specifications could be different from different
manufacuturers so please check with each manufacturer if
additional information is needed.
For the output capacitor, a ceramic capacitor can be used
because of the low ESR values, which helps to minimize the
output voltage ripple. A typical value of 10μF/6.3V ceramic
capacitor should be enough for most of the applications and
the capacitor should be X5R or X7R.
FN6509.0
June 29, 2007
相关PDF资料 |
PDF描述 |
|---|---|
| ISL9107IRZ-T | IC REG BUCK SYNC ADJ 1.5A 8DFN |
| ISL9109IRZ-T | IC REG BUCK SYNC ADJ 1.5A 8DFN |
| ISL9110AIITNZ-T | IC VOLTAGE REGULATOR |
| ISL9111EH30Z-T | IC VOLTAGE REGULATOR |
| ISL9112IRT7Z-T7A | IC REG BUCK BOOST SYNC 5V 12TDFN |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ISL9106IRZ-T | 功能描述:IC REG BUCK SYNC ADJ 1.2A 10DFN RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 标准包装:1,000 系列:- 类型:降压（降压） 输出类型:可调式 输出数:1 输出电压:0.6 V ~ 4.5 V 输入电压:3 V ~ 5.5 V PWM 型:电流模式 频率 - 开关:3MHz 电流 - 输出:1.5A 同步整流器:无 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:6-WDFN 裸露焊盘 包装:带卷 (TR) 供应商设备封装:6-LLP-EP（3x3） 产品目录页面:1300 (CN2011-ZH PDF) 其它名称:LM2831ZSDLM2831ZSDTR |
| ISL9106IRZ-TS2708 | 制造商:Intersil Corporation 功能描述:ITSISL9106IRZ-TS2708 INTELION / ATHEROS |
| ISL9107 | 制造商:INTERSIL 制造商全称:Intersil Corporation 功能描述:1.5A 1.6MHz Low Quiescent Current High Efficiency Synchronous Buck Regulator |
| ISL9107EVAL1Z | 功能描述:电源管理IC开发工具 ISL9107 EVALUATION BOARD 1 - RoHS COMPLIANT - DFN RoHS:否 制造商:Maxim Integrated 产品:Evaluation Kits 类型:Battery Management 工具用于评估:MAX17710GB 输入电压: 输出电压:1.8 V |
| ISL9107IRZ-T | 功能描述:直流/直流开关转换器 W/ANNEAL LW IQ BUCK REGW/INTEGRATEDFET RoHS:否 制造商:STMicroelectronics 最大输入电压:4.5 V 开关频率:1.5 MHz 输出电压:4.6 V 输出电流:250 mA 输出端数量:2 最大工作温度:+ 85 C 安装风格:SMD/SMT |
发布紧急采购，3分钟左右您将得到回复。