参数资料
| 型号： | ISL95870BHRZ-T |
| 厂商： | Intersil |
| 文件页数： | 22/28页 |
| 文件大小： | 0K |
| 描述： | IC CTRLR PWM 1PHASE GPU 20QFN |
| 标准包装： | 6,000 |
| 应用： | 控制器，GPU 内核电源 |
| 输入电压： | 3.3 V ~ 25 V |
| 输出数： | 1 |
| 输出电压： | 0.5 V ~ 5 V |
| 工作温度： | -10°C ~ 100°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 20-VFQFN 裸露焊盘 |
| 供应商设备封装： | 20-QFN（3x4） |
| 包装： | 带卷 (TR) |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页当前第22页第23页第24页第25页第26页第27页第28页
ISL95870, ISL95870A, ISL95870B
A DC/DC buck regulator must have output capacitance C O into
which ripple current I P-P can flow. Current I P-P develops a
corresponding ripple voltage V P-P across C O, which is the sum of
the voltage drop across the capacitor ESR and of the voltage
change stemming from charge moved in and out of the
capacitor. These two voltages are expressed in Equations 39
UGATE
and 40:
Δ V C = ---------------------------------
1V
1V
Δ V ESR = I P-P ? E SR
I P-P
8 ? C O ? F SW
(EQ. 39)
(EQ. 40)
1V
LGATE
1V
If the output of the converter has to support a load with high
pulsating current, several capacitors will need to be paralleled to
reduce the total ESR until the required V P-P is achieved. The
inductance of the capacitor can significantly impact the output
voltage ripple and cause a brief voltage spike if the load transient
FIGURE 18. GATE DRIVE ADAPTIVE SHOOT-THROUGH PROTECTION
General Application Design
Guide
This design guide is intended to provide a high-level explanation of
the steps necessary to design a single-phase buck converter. It is
assumed that the reader is familiar with many of the basic skills
and techniques referenced in the following. In addition to this
guide, Intersil provides complete reference designs that include
schematics, bills of materials, and example board layouts.
Selecting the LC Output Filter
The duty cycle of an ideal buck converter is a function of the
input and the output voltage. This relationship is expressed in
Equation 36:
has an extremely high slew rate. Low inductance capacitors should
be considered. A capacitor dissipates heat as a function of RMS
current and frequency. Be sure that I P-P is shared by a sufficient
quantity of paralleled capacitors so that they operate below the
maximum rated RMS current at F SW . Take into account that the
rated value of a capacitor can fade as much as 50% as the DC
voltage across it increases.
Selecting the Input Capacitor
The important parameters for the bulk input capacitors are the
voltage rating and the RMS current rating. For reliable operation,
select bulk capacitors with voltage and current ratings above the
maximum input voltage and capable of supplying the RMS
current required by the switching circuit. Their voltage rating
should be at least 1.25x greater than the maximum input
voltage, while a voltage rating of 1.5x is a preferred rating. Figure
19 is a graph of the input RMS ripple current, normalized relative
V O
D = ---------
V IN
(EQ. 36)
to output load current, as a function of duty cycle that is adjusted
for converter efficiency. The ripple current calculation is written as
Equation 41:
V O ? ( 1 – D )
I P-P = -------------------------------
(EQ. 38)
P COPPER = I LOAD ? DCR
( I MAX ? ( D – D ) ) + ? x ? I MAX ? ------ ?
V O
V IN ? EFF
The output inductor peak-to-peak ripple current is expressed in
Equation 37:
(EQ. 37)
F SW ? L
A typical step-down DC/DC converter will have an I PP of 20% to
40% of the maximum DC output load current. The value of I P-P is
selected based upon several criteria such as MOSFET switching
loss, inductor core loss, and the resistive loss of the inductor
winding. The DC copper loss of the inductor can be estimated
using Equation 38:
2
Where, I LOAD is the converter output DC current.
The copper loss can be significant so attention has to be given to
the DCR of the inductor. Another factor to consider when
choosing the inductor is its saturation characteristics at elevated
temperature. A saturated inductor could cause destruction of
circuit components, as well as nuisance OCP faults.
22
2 2 2 2 D
? 12 ? (EQ. 41)
I IN_RMS = --------------------------------------------------------------------------------------------------------
I MAX
Where:
- I MAX is the maximum continuous I LOAD of the converter
- x is a multiplier (0 to 1) corresponding to the inductor
peak-to-peak ripple amplitude expressed as a percentage of
I MAX (0% to 100%)
- D is the duty cycle that is adjusted to take into account the
efficiency of the converter
Duty cycle is written as Equation 42:
D = -------------------------- (EQ. 42)
FN6899.1
December 2, 2013
相关PDF资料 |
PDF描述 |
|---|---|
| HIP6006CBZ-T | IC CTRLR PWM BUCK SYNC 14-SOIC |
| RGM06DTAD-S664 | CONN EDGECARD 12POS R/A .156 SLD |
| ACM25DSEP-S243 | CONN EDGECARD 50POS .156 EYELET |
| RBM22DRST-S288 | CONN EDGECARD 44POS .156 EXTEND |
| ABM25DSEP-S243 | CONN EDGECARD 50POS .156 EYELET |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ISL95870BHRZ-TS2490 | 制造商:Intersil Corporation 功能描述:IBM, ISL95870BHRZ-T W/CONTAINER LABELING - Tape and Reel |
| ISL95870BHRZ-TS2568 | 制造商:Intersil Corporation 功能描述:INTEL, ISL95870BHRTZ-T W/BARCODE LABELS, 12 MONTH D/C RESTRI - Tape and Reel |
| ISL95870BIRZ | 功能描述:电流型 PWM 控制器 0/2 BIT PWM GPU CONTLR FOR NOTEBOOK RoHS:否 制造商:Texas Instruments 开关频率:27 KHz 上升时间: 下降时间: 工作电源电压:6 V to 15 V 工作电源电流:1.5 mA 输出端数量:1 最大工作温度:+ 105 C 安装风格:SMD/SMT 封装 / 箱体:TSSOP-14 |
| ISL95870BIRZ-T | 功能描述:电流型 PWM 控制器 0/2 BIT PWM GPU CONTLR FOR NOTEBOOK RoHS:否 制造商:Texas Instruments 开关频率:27 KHz 上升时间: 下降时间: 工作电源电压:6 V to 15 V 工作电源电流:1.5 mA 输出端数量:1 最大工作温度:+ 105 C 安装风格:SMD/SMT 封装 / 箱体:TSSOP-14 |
| ISL95870HRUZ-T | 功能描述:电流型 PWM 控制器 0/2 BIT PWM GPU CONTLR FOR NOTEBOOK RoHS:否 制造商:Texas Instruments 开关频率:27 KHz 上升时间: 下降时间: 工作电源电压:6 V to 15 V 工作电源电流:1.5 mA 输出端数量:1 最大工作温度:+ 105 C 安装风格:SMD/SMT 封装 / 箱体:TSSOP-14 |
发布紧急采购，3分钟左右您将得到回复。