参数资料
| 型号： | ISL97702IRZ-T7 |
| 厂商： | Intersil |
| 文件页数： | 8/13页 |
| 文件大小： | 0K |
| 描述： | IC REG BOOST ADJ 0.13A DL 10DFN |
| 标准包装： | 1,000 |
| 类型： | 升压（升压） |
| 输出类型： | 可调式 |
| 输出数： | 2 |
| 输出电压： | 可调至 28V |
| 输入电压： | 2.3 V ~ 5.5 V |
| 频率 - 开关： | 1MHz |
| 电流 - 输出： | 130mA |
| 同步整流器： | 无 |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 10-VFDFN 裸露焊盘 |
| 包装： | 带卷 (TR) |
| 供应商设备封装： | 10-DFN（3x3） |
ISL97702
Pin Descriptions
PIN
Description of Operation
Enable Pin (active low) - NEN
NUMBER
1
2
3
4
5
6
7
8
9
10
PIN NAME
GND
VDDOUT
VDD
NSYNC
FB0
FB1
SEL
NEN
V OUT
LX
PIN FUNCTION
Ground
Protection Switch Output
Supply Input
Synchronization Input (Falling Edge)
Feedback Input 0
Feedback Input 1
Select Input
Enable Input (Active Low)
Boost Output Voltage
Boost FET
If NEN is high the ISL97702 shuts down all its internal
functions and deactivates its I/Os. Only the internal pull-up
resistor at NEN remains active. If NEN is high the input
disconnect switch between VDD and VDDOUT interrupts the
circuit path from the input voltage VDD through inductor and
diode to the output load at V OUT . If shut down the total
supply current in VDD is typically less than 0.1μA.
When NEN is driven low the ISL97702 begins with the start-
up sequence.
Start-Up Sequence
After pin NEN is pulled low or a restart is triggered from Fault
Control during operation, the ISL97702 goes through a start-
up sequence with the following six states: Soft Inrush ->
Function Overview
The ISL97702 is a high frequency, high efficiency boost
regulator which operates in constant frequency PWM mode.
The boost converter generates a stable, higher output
voltage from a variable, low voltage input source (e.g. Li-Ion
battery). Two output voltage levels are pin selectable with
values defined from the feedback resistor network.
The switching frequency is either generated from the fixed
1MHz internal oscillator or provided externally at the
synchronization pin in the range from 600kHz to 1.4MHz.
The compensation network and soft-start functions are built
in with fixed parameters without any need for further external
components.
To stop battery discharge into the output load when disabled
the inductor is disconnected from the input supply with a low
on resistance power switch.
Built in fault protection monitors inductor current and output
voltage as well as junction temperature in order to interrupt
the high current circuit path through the inductor and diode in
the event of a load failure.
Low logic input thresholds allow the ISL97702 to interface
directly to micro controllers with lower supply voltage.
Alternatively the internal pull-up resistors on all logic inputs
provide level shifting when driven from open collector outputs.
8
VDDOUT Enable -> Soft Boost 25 -> Soft Boost 50 -> Soft
Boost 75 -> Normal.
If the sequence has completed, the ISL97702 stays in the
“Normal” state until NEN is high again or any fault is detected.
Soft Inrush: State Duration ~2.048ms
The switch at VDDOUT is configured as current source and
provides a limited current through the inductor to pre-charge
the capacitor at V OUT .
VDDOUT Enable: State Duration ~128μs
The switch at VDDOUT is fully enabled and connects the
inductor to VDD with a low on-resistance.
Soft Boost 25 -> 50 -> 75: State Duration 3x ~2.048ms
The boost regulator begins to switch at LX.
The LX current limit increases in three steps representing
25%, 50% 75% of its final value.
Normal
If no fault was detected Normal state is entered ~8.256ms
after NEN is pulled low.
The LX current limit steps up to 100%.
In all states Fault Control can force the sequence to restart
or even to shut down (see Table 1).
FN7462.0
October 13, 2005
相关PDF资料 |
PDF描述 |
|---|---|
| ISL98012IUZ | IC REG BOOST ADJ 0.6A 10MSOP |
| ISPPAC-POWR1208-01TN44E | IC ISP POWER MGR ANLG/LOG 44TQFP |
| ISPPAC-POWR604-01TN44E | IC ISP POWER MGR ANLG/LOG 44TQFP |
| ISPPAC-POWR6AT6-01NN32I | IC ISP POWER SUPPLY PROGR 32QFN |
| IXDS502D1B | IC GATE LS DRVR SGL 2A 6-DFN |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ISL97801ARZ | 功能描述:IC LED DRIVER AUTOMOTIVE 20-QFN RoHS:是 类别:集成电路 (IC) >> PMIC - LED 驱动器 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,500 系列:- 恒定电流:- 恒定电压:- 拓扑:升压（升压），切换式电容器（充电泵） 输出数:1 内部驱动器:是 类型 - 主要:背光 类型 - 次要:白色 LED 频率:625kHz ~ 875kHz 电源电压:2.7 V ~ 5.3 V 输出电压:5V 安装类型:表面贴装 封装/外壳:10-TFSOP，10-MSOP（0.118"，3.00mm 宽） 供应商设备封装:10-µMAX 包装:带卷 (TR) 工作温度:-40°C ~ 85°C |
| ISL97801ARZ-T | 功能描述:IC LED DRIVER AUTOMOTIVE 20-QFN RoHS:是 类别:集成电路 (IC) >> PMIC - LED 驱动器 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,500 系列:- 恒定电流:- 恒定电压:- 拓扑:升压（升压），切换式电容器（充电泵） 输出数:1 内部驱动器:是 类型 - 主要:背光 类型 - 次要:白色 LED 频率:625kHz ~ 875kHz 电源电压:2.7 V ~ 5.3 V 输出电压:5V 安装类型:表面贴装 封装/外壳:10-TFSOP，10-MSOP（0.118"，3.00mm 宽） 供应商设备封装:10-µMAX 包装:带卷 (TR) 工作温度:-40°C ~ 85°C |
| ISL97801ARZ-TK | 功能描述:IC LED DRIVER AUTOMOTIVE 20-QFN RoHS:是 类别:集成电路 (IC) >> PMIC - LED 驱动器 系列:- 标准包装:60 系列:- 恒定电流:- 恒定电压:- 拓扑:线性（LDO），PWM，升压（升压） 输出数:8 内部驱动器:是 类型 - 主要:背光 类型 - 次要:RGB，白色 LED 频率:500kHz ~ 1.5MHz 电源电压:4.75 V ~ 26 V 输出电压:45V 安装类型:* 封装/外壳:* 供应商设备封装:* 包装:* 工作温度:-40°C ~ 85°C |
| ISL97801BOOSTEVALZ | 功能描述:EVAL BOARD FOR ISL97801 RoHS:是 类别:编程器，开发系统 >> 评估板 - LED 驱动器 系列:* 标准包装:1 系列:PowerWise® 电流 - 输出 / 通道:20mA 输出及类型:1，非隔离 输出电压:17V 特点:可调光 输入电压:2.7 ~ 5.5 V 已供物品:板 已用 IC / 零件:LM3508 相关产品:LM3508TLX-ND - IC LED DRVR WHT BCKLGT 9USMDLM3508TLDKR-ND - IC LED DRVR WHT BCKLGT 9MICROSMDLM3508TLCT-ND - IC LED DRVR WHT BCKLGT 9MICROSMDLM3508TLTR-ND - IC LED DRVR WHT BCKLGT 9MICROSMD |
| ISL97900CRZ | 功能描述:LED照明驱动器 High Current RGB Driver/Controller, 28L 4x5 QFN, Commercial RoHS:否 制造商:STMicroelectronics 输入电压:11.5 V to 23 V 工作频率: 最大电源电流:1.7 mA 输出电流: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:SO-16N |
发布紧急采购，3分钟左右您将得到回复。