参数资料
| 型号： | KAD5610P-25Q72 |
| 厂商： | Intersil |
| 文件页数： | 6/30页 |
| 文件大小： | 0K |
| 描述： | IC ADC 10BIT 250MSPS DUAL 72-QFN |
| 产品培训模块： | High-Speed Analog-to-Digital Converters |
| 标准包装： | 1 |
| 系列： | FemtoCharge™ |
| 位数： | 10 |
| 采样率（每秒）： | 250M |
| 数据接口： | 串行，SPI? |
| 转换器数目： | 2 |
| 功率耗散（最大）： | 438mW |
| 电压电源： | 单电源 |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 72-VFQFN 裸露焊盘 |
| 供应商设备封装： | 72-QFN（10x10） |
| 包装： | 托盘 |
| 输入数目和类型： | 2 个差分，单极 |
第1页第2页第3页第4页第5页当前第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页
14
FN6810.2
September 10, 2009
Theory of Operation
Functional Description
The KAD5610P is based upon a 10-bit, 250MSPS A/D
converter core that utilizes a pipelined successive
approximation architecture (Figure 22). The input voltage is
captured by a Sample-Hold Amplifier (SHA) and converted to
a unit of charge. Proprietary charge-domain techniques are
used to successively compare the input to a series of
reference charges. Decisions made during the successive
approximation operations determine the digital code for each
input value. The converter pipeline requires six samples to
produce a result. Digital error correction is also applied,
resulting in a total latency of seven and one half clock cycles.
This is evident to the user as a latency between the start of a
conversion and the data being available on the digital outputs.
The device contains two A/D converter cores with carefully
matched transfer characteristics. At start-up, each core
performs a self-calibration to minimize gain and offset errors.
The reset pin (RESETN) is initially set high at power-up and
will remain in that state until the calibration is complete. The
clock frequency should remain fixed during this time, and no
SPI communications should be attempted. Recalibration can
be initiated via the SPI port at any time after the initial
self-calibration.
Power-On Calibration
The ADC performs a self-calibration at start-up. An internal
power-on-reset (POR) circuit detects the supply voltage
ramps and initiates the calibration when the analog and
digital supply voltages are above a threshold. The following
conditions must be adhered to for the power-on calibration to
execute successfully:
A frequency-stable conversion clock must be applied to
the CLKP/CLKN pins
DNC pins (especially 3, 4 and 18) must not be pulled up or
down
SDO (pin 66) must be high
RESETN (pin 25) must begin low
SPI communications must not be attempted
A user-initiated reset can subsequently be invoked in the
event that the above conditions cannot be met at power-up.
The SDO pin requires an external 4.7k
Ω pull-up to OVDD. If
the SDO pin is pulled low externally during power-up,
calibration will not be executed properly.
After the power supply has stabilized the internal POR
releases RESETN and an internal pull-up pulls it high, which
starts the calibration sequence. If a subsequent
user-initiated reset is required, the RESETN pin should be
connected to an open-drain driver with a drive strength of
less than 0.5mA.
The calibration sequence is initiated on the rising edge of
RESETN, as shown in Figure 23. The over-range output
(OR) is set high once RESETN is pulled low, and remains in
that state until calibration is complete. The OR output returns
to normal operation at that time, so it is important that the
analog input be within the converter’s full-scale range to
observe the transition. If the input is in an over-range
condition the OR pin will stay high, and it will not be possible
to detect the end of the calibration cycle.
FIGURE 22. ADC CORE BLOCK DIAGRAM
DIGITAL
ERROR
CORRECTION
SHA
1.25V
INP
INN
CLOCK
GENERATION
2.5-BIT
FLASH
6-STAGE
1.5-BIT/STAGE
3-STAGE
1-BIT/STAGE
3-BIT
FLASH
LVDS/LVCMOS
OUTPUTS
+
–
KAD5610P
相关PDF资料 |
PDF描述 |
|---|---|
| KAD5612P-17Q72 | IC ADC 12BIT 170MSPS DUAL 72-QFN |
| LA72715NV-TLM-E | IC AUDIO DECODER JPN MTS 24SSOP |
| LICAL-DEC-LS001 | IC DECODER LOW SECURITY 8DIP |
| LICAL-DEC-MS001 | IC DECODER MS SERIES 20-SSOP |
| LICAL-ENC-MS001 | IC ENCODER MS SERIES 20-SSOP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| KAD5612P | 制造商:INTERSIL 制造商全称:Intersil Corporation 功能描述:Dual 12-Bit, 250/210/170/125MSPS A/D Converter |
| KAD5612P_09 | 制造商:INTERSIL 制造商全称:Intersil Corporation 功能描述:Dual 12-Bit, 250/210/170/125MSPS A/D Converter |
| KAD5612P_0909 | 制造商:INTERSIL 制造商全称:Intersil Corporation 功能描述:Dual 12-Bit, 250/210/170/125MSPS A/D Converter |
| KAD5612P-12Q72 | 功能描述:IC ADC 12BIT 125MSPS DUAL 72-QFN RoHS:是 类别:集成电路 (IC) >> 数据采集 - 模数转换器 系列:FemtoCharge™ 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:250 系列:- 位数:12 采样率（每秒）:1.8M 数据接口:并联 转换器数目:1 功率耗散（最大）:1.82W 电压电源:模拟和数字 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:48-LQFP 供应商设备封装:48-LQFP（7x7） 包装:管件 输入数目和类型:2 个单端，单极 |
| KAD5612P-17Q72 | 功能描述:IC ADC 12BIT 170MSPS DUAL 72-QFN RoHS:是 类别:集成电路 (IC) >> 数据采集 - 模数转换器 系列:FemtoCharge™ 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:250 系列:- 位数:12 采样率（每秒）:1.8M 数据接口:并联 转换器数目:1 功率耗散（最大）:1.82W 电压电源:模拟和数字 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:48-LQFP 供应商设备封装:48-LQFP（7x7） 包装:管件 输入数目和类型:2 个单端，单极 |
发布紧急采购，3分钟左右您将得到回复。