- 您现在的位置：买卖IC网 > PDF目录17242 > KIT33701DWBEVB (Freescale Semiconductor)KIT FOR 33701 POWER SUPPLY PDF资料下载
参数资料
| 型号： | KIT33701DWBEVB |
| 厂商： | Freescale Semiconductor |
| 文件页数： | 26/39页 |
| 文件大小： | 0K |
| 描述： | KIT FOR 33701 POWER SUPPLY |
| 标准包装： | 1 |
| 主要目的： | DC/DC，LDO 步降 |
| 输出及类型： | 2，非隔离 |
| 输入电压： | 2.8 ~ 6V |
| 稳压器拓扑结构： | 降压 |
| 频率 - 开关： | 300kHz |
| 板类型： | 完全填充 |
| 已供物品： | 板，软件 |
| 已用 IC / 零件： | MC34701 |
| 相关产品： | MC34701EKR2CT-ND - IC POWER SUPPLY MCU 1A 32-SOIC MC34701EKR2TR-ND - IC POWER SUPPLY MCU 1A 32-SOIC MC34701EK-ND - IC POWER SUPPLY MCU 1A 32-SOIC |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页当前第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页
FUNCTIONAL DEVICE OPERATION
OPERATIONAL MODES
1. LDO falls faster than VOUT . The VOUT uses control
methods (4) and (5) described in the section Methods
In the case VIN1 = VIN2, the intrinsic operation turns
on both the buck high side MOSFET and the LDO
external Pass MOSFET, and discharges the VOUT
load capacitor into the VIN supply.
2. VOUT falls faster than LDO. The LDO uses control
methods (5) and (6) described in the section Methods
Shorted Load
1. LDO shorted to ground. The VOUT uses methods (1)
2. VOUT shorted to ground. The LDO uses control
methods (5) and (6) described in the section Methods
3. VIN1 shorted to ground. Device is not working.
4. VIN2 shorted to ground. This is equivalent to the
switcher V OUT output shorted to ground.
5. LDO shorted to supply. No load protection. 34701 is
protected by current limit and thermal shutdown.
6. VOUT shorted to supply. No load protection. 34701 is
protected by current limit and thermal shutdown.
LOGIC COMMANDS AND REGISTERS
I 2 C BUS OPERATION
The 34701 device is compatible with the I 2 C interface
standard. SDA and SCL pins are the Serial Data and Serial
Clock pins of the I 2 C bus.
I 2 C COMMAND AND DATA FORMATS
assure its unique address. Figure 21 illustrates the flexible
addressing feature for a 7-bit address. Table 6 provides the
definition of the selectable portion of the device address.
When the ADDR pin is used and put to low level, pull the
ADDR pin to ground through a 10k ? resistor.
Communication Start
Communication starts with a START condition, followed by
the slave device unique address. The Read/Write (R/W) bit
MSB
6
1
5
1
4
1
Bits LSB
3 2 1 0
0 1 A1 A0
defines whether the data should be read from or written to the
device (the 34701 operates only as a slave device; therefore,
the R/W bit should always be set to 0). The 34701 responds
by sending the Acknowledge bit (Ack) to the master device.
Figure 20 illustrates the beginning of an I 2 C communication
for a 7-bit slave address.
Fixed Address Selectable
Address
Figure 21. Address Bit Definition for 7-Bit Address
Table 6. Definition of Selectable Portion of Device
Address
CLKSEL Pin
ADDR Pin
A1
A0
S
7-Bit Address
R/W
Ack
Low
Low
0
0
Figure 20. Communication Start Using 7-Bit Address
Slave Address Definition
34701 has the two least significant address bits (LSB)
Low
High (Open)
High (Open)
High (Open)
Low
High (Open)
0
1
1
1
0
1
defined by the state of the CLKSEL pin (A1) and the ADDR
pin (A0).
Note The state of the CLKSEL pin also defines the
configuration of the oscillator synchronization CLKSYN pin.
Leaving the CLKSEL pin open or pulling it high defines the
CLKSYN pin as an oscillator output. When the CLKSEL pin
is pulled low, the CLKSYN pin is configured as a
synchronization input for the external clock signal.
This feature allows up to four 34701 ICs to communicate
in the same I 2 C bus, all of them sharing the same high order
address bits. A different combination of the two LSB address
bits A1 and A0 can be assigned to each individual part to
Writing Data Into the Slave Device
After the address acknowledgment by the slave, DATA
can be written into the slave registers. The R/W bit must be
set to 0 to allow DATA to be written into the 34702. Figure 22
shows the data write sequence. Actions performed by the
slave device are grayed. ?
S 7-Bit Address 0 Ack DATA Ack
(Write)
Figure 22. Data Transfer for Write Operations
34701
Analog Integrated Circuit Device Data ?
26
Freescale Semiconductor
相关PDF资料 |
PDF描述 |
|---|---|
| RB-1505D/H | CONV DC/DC 1W 15VIN +/-05VOUT |
| R1D-123.3/HP-R | CONV DC/DC 1W 12VIN +/-3.3VOUT |
| MCP1407-E/MF | IC MOSFET DVR 6A 8DFN |
| MCP1406-E/MF | IC MOSFET DVR 6A 8DFN |
| R1D-1224/HP-R | CONV DC/DC 1W 12VIN +/-24VOUT |
相关代理商/技术参数 |
参数描述 |
|---|---|
| KIT33702DWBEVB | 功能描述:电源管理IC开发工具 33702 - QS2 EVAL KIT RoHS:否 制造商:Maxim Integrated 产品:Evaluation Kits 类型:Battery Management 工具用于评估:MAX17710GB 输入电压: 输出电压:1.8 V |
| KIT33730EKEVBE | 功能描述:电源管理IC开发工具 SWITCH MODE PWR SUP RoHS:否 制造商:Maxim Integrated 产品:Evaluation Kits 类型:Battery Management 工具用于评估:MAX17710GB 输入电压: 输出电压:1.8 V |
| KIT33742DWEVB | 功能描述:网络开发工具 SBC WITH EHSCAN RoHS:否 制造商:Rabbit Semiconductor 产品:Development Kits 类型:Ethernet to Wi-Fi Bridges 工具用于评估:RCM6600W 数据速率:20 Mbps, 40 Mbps 接口类型:802.11 b/g, Ethernet 工作电源电压:3.3 V |
| KIT3376MMA7330L | 功能描述:加速传感器开发工具 XYZ-AXIS ANALOG ACCELERO RoHS:否 制造商:Murata 工具用于评估:SCA3100-D04 加速:2 g 传感轴:Triple Axis 接口类型:SPI 工作电压:3.3 V |
| KIT3376MMA7331L | 功能描述:加速传感器开发工具 3-AXIS ANALOG OUT 4g /12g Dev Kit RoHS:否 制造商:Murata 工具用于评估:SCA3100-D04 加速:2 g 传感轴:Triple Axis 接口类型:SPI 工作电压:3.3 V |
发布紧急采购，3分钟左右您将得到回复。