- 您现在的位置：买卖IC网 > PDF目录17242 > KIT33701DWBEVB (Freescale Semiconductor)KIT FOR 33701 POWER SUPPLY PDF资料下载
参数资料
| 型号： | KIT33701DWBEVB |
| 厂商： | Freescale Semiconductor |
| 文件页数： | 32/39页 |
| 文件大小： | 0K |
| 描述： | KIT FOR 33701 POWER SUPPLY |
| 标准包装： | 1 |
| 主要目的： | DC/DC，LDO 步降 |
| 输出及类型： | 2，非隔离 |
| 输入电压： | 2.8 ~ 6V |
| 稳压器拓扑结构： | 降压 |
| 频率 - 开关： | 300kHz |
| 板类型： | 完全填充 |
| 已供物品： | 板，软件 |
| 已用 IC / 零件： | MC34701 |
| 相关产品： | MC34701EKR2CT-ND - IC POWER SUPPLY MCU 1A 32-SOIC MC34701EKR2TR-ND - IC POWER SUPPLY MCU 1A 32-SOIC MC34701EK-ND - IC POWER SUPPLY MCU 1A 32-SOIC |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页当前第32页第33页第34页第35页第36页第37页第38页第39页
TYPICAL APPLICATIONS
P D ? Q ? max ? -----------------------------------------------------------
Linear Regulator Current Limit
As described in the Linear Regulator Functional
Description section, the current limit of the linear regulator
can be adjusted by means of an external current sense
resistor R S . The voltage drop caused by the regulator output
current flowing through the current sense resistor R S is
sensed between the LDO and the CS pins. When the sensed
voltage exceeds 50mV (typical), the current limit timer starts
to time out while the control circuit limits the output current. If
the over-current condition lasts for more than 10ms, the linear
regulator is shut off and turned on again after 100ms. This
type of operation provides equivalent protection to the analog
“current foldback” operation.
It is important to keep in mind that the amount of capacitive
load which can be supplied by the by the linear regulator is
limited by the setting of the LDO current limit. During the
power-up period, the linear regulator operates in the current
limit, supplying the current into the load of the LDO, which
includes all the capacitors connected to the regulator output.
If the total amount load is so large that the regulator could not
reach its regulation voltage in 10ms during the power-up, it
turns off and tries to power up again after 100ms. This
situation may lead to the power-up oscillations.
Linear Regulator External MOSFET
The linear regulator uses an external N-channel power
MOSFET to provide a pass element for the power path. The
selection of the proper type of the external power MOSFET is
critical for optimum performance and safe operation of the
linear regulator.
The power MOSFET’s threshold voltage, R DS(on) , gate
charge, capacitances and transconductance are important
parameters for the stable operation of the linear regulator
while the package of the power MOSFET determines the
maximum power dissipation, and hence the maximum output
current for the required input-to-output voltage drop. The
power dissipation of the external MOSFET can be calculated
from the simple formula:
P D ? Q ? = I LDO ? ? V IN – V LDO ?
Where P D(Q) is the power MOSFET power dissipation ?
VIN is the LDO input voltage, ?
VLDO is the LDO output voltage, ?
ILDO is the LDO output load current.
Table 10 shows the recommended power MOSFET types
for the 34701 linear regulator, their typical power dissipation,
and thermal resistance junction-to-case.
Table 10. Recommended Power MOSFETs
NOTE : Freescale does not assume liability, endorse, or warrant
components from external manufacturers referenced in figures
or tables. Although Freescale offers component
recommendations, it is the customer’s responsibility to validate
their application.
*When mounted to an FR4 using 0.5 sq.in. drain pad size
The maximum power dissipation is limited by the
maximum operating junction temperature T Jmax . The
allowed power dissipation in the given application can be
calculated from the following expression:
T Jmax – T A
R thJC + R thCB + R thBA
Where P D(Q)max is the power MOSFET maximum
allowed dissipation, ?
T Jmax is the power MOSFET maximum operating
junction temperature, ?
T A is the ambient temperature, ?
R thJC is the power MOSFET thermal resistance
junction-to-case, ?
R thCB is the thermal resistance case-to-board, ?
R thBA is the thermal resistance board-to-ambient of
the PC board.
PCB Layout Considerations
As with any power application, the proper PCB layout
plays a critical role in the overall power regulator
performance. While good careful printed circuit board layout
significantly improves regulation parameters and
electromagnetic compatibility (EMC) performance of the
switching regulator, poor layout practices can lead not only to
significant degradation of regulation and EMC parameters,
but even to total dysfunction of the whole regulator IC.
Extreme care should be taken when laying out the ground
of the regulator circuit. In order to avoid any inductive or
capacitive coupling of the switching regulator noise into the
sensitive analog control circuits, the noisy power ground and
the clean quiet signal ground should be well separated on the
printed circuit board, and connected only at one connection
point. The power routing should be made by heavy traces or
areas of copper. The power path and its return should be
placed, if possible, atop each other on the different layers or
opposite sides of the PC board. The switching regulator input
and output capacitors should be physically placed very close
to the power pins (VIN2, SW, PGND) of the 34701 switching
regulator; and their ground pins, together with the 34701
power ground pins (PGND), should be connected by a single
island of the power ground copper to create the “single-point”
grounding. Figure 32 illustrates the 34701 switching regulator
grounding concept. The bootstrap capacitor C b should be
tightly connected to the integrated circuit as well.
Part No.
IRL2703S
MTD20N03HDL
Package
D2PAK
DPAK
Typ. P D
2.0W
1.75W*
R thJ-C
3.3°C/W
1.67°C/W
34701
Analog Integrated Circuit Device Data ?
32
Freescale Semiconductor
相关PDF资料 |
PDF描述 |
|---|---|
| RB-1505D/H | CONV DC/DC 1W 15VIN +/-05VOUT |
| R1D-123.3/HP-R | CONV DC/DC 1W 12VIN +/-3.3VOUT |
| MCP1407-E/MF | IC MOSFET DVR 6A 8DFN |
| MCP1406-E/MF | IC MOSFET DVR 6A 8DFN |
| R1D-1224/HP-R | CONV DC/DC 1W 12VIN +/-24VOUT |
相关代理商/技术参数 |
参数描述 |
|---|---|
| KIT33702DWBEVB | 功能描述:电源管理IC开发工具 33702 - QS2 EVAL KIT RoHS:否 制造商:Maxim Integrated 产品:Evaluation Kits 类型:Battery Management 工具用于评估:MAX17710GB 输入电压: 输出电压:1.8 V |
| KIT33730EKEVBE | 功能描述:电源管理IC开发工具 SWITCH MODE PWR SUP RoHS:否 制造商:Maxim Integrated 产品:Evaluation Kits 类型:Battery Management 工具用于评估:MAX17710GB 输入电压: 输出电压:1.8 V |
| KIT33742DWEVB | 功能描述:网络开发工具 SBC WITH EHSCAN RoHS:否 制造商:Rabbit Semiconductor 产品:Development Kits 类型:Ethernet to Wi-Fi Bridges 工具用于评估:RCM6600W 数据速率:20 Mbps, 40 Mbps 接口类型:802.11 b/g, Ethernet 工作电源电压:3.3 V |
| KIT3376MMA7330L | 功能描述:加速传感器开发工具 XYZ-AXIS ANALOG ACCELERO RoHS:否 制造商:Murata 工具用于评估:SCA3100-D04 加速:2 g 传感轴:Triple Axis 接口类型:SPI 工作电压:3.3 V |
| KIT3376MMA7331L | 功能描述:加速传感器开发工具 3-AXIS ANALOG OUT 4g /12g Dev Kit RoHS:否 制造商:Murata 工具用于评估:SCA3100-D04 加速:2 g 传感轴:Triple Axis 接口类型:SPI 工作电压:3.3 V |
发布紧急采购，3分钟左右您将得到回复。