- 您现在的位置：买卖IC网 > PDF目录15794 > KIT33993DWBEVB (Freescale Semiconductor)KIT EVAL FOR MC33993 SWITCH DET PDF资料下载
参数资料
| 型号： | KIT33993DWBEVB |
| 厂商： | Freescale Semiconductor |
| 文件页数： | 13/28页 |
| 文件大小： | 0K |
| 描述： | KIT EVAL FOR MC33993 SWITCH DET |
| 标准包装： | 1 |
| 类型： | 微控制器 |
| 适用于相关产品： | MC33993 |
| 所含物品： | 评估板、数据表和说明文档 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页当前第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页
Analog Integrated Circuit Device Data
20
Freescale Semiconductor
33993
TYPICAL APPLICATIONS
INTRODUCTION
ARCHIVE
INFORMATION
ARCHIVE
INFORMATION
TYPICAL APPLICATIONS
INTRODUCTION
The 33993’s primary function is the detection of open or
closed switch contacts. However, there are many features
that allow the device to be used in a variety of applications.
The following is a list of applications to consider for the IC:
Sensor Power Supply
Switch Monitor for Metallic or Elastomeric Switches
Analog Sensor Inputs (Ratiometric)
Power MOSFET/LED Driver and Monitor
Multiple 33993 Devices in a Module System
The following paragraphs describe the applications in
detail.
SENSOR POWER SUPPLY
Each input may be used to supply current to sensors
external to a module. Many sensors such as Hall effect,
pressure sensors, and temperature sensors require a supply
voltage to power the sensor and provide an open collector or
analog output. Figure 12 shows how the 33993 may be used
to supply power and interface to these types of sensors. In an
application where the input makes continuous transitions,
consider using the wake-up/interrupt command to disable
the interrupt for the particular input.
Figure 12. Sensor Power Supply
METALLIC/ELASTOMERIC SWITCH
Metallic switch contacts often develop higher contact
resistance over time owing to contact corrosion. The
corrosion is induced by humidity, salt, and other elements
that exist in the environment. For this reason the 33993
provides two settings for contacts. When programmed for
metallic switches, the device provides higher wetting current
to keep switch contacts free of oxides. The higher current
occurs for the first 20 ms of switch closure. Where longer
duration of wetting current is desired, the user may send the
wetting current timer command and disable the timer. Wetting
current will be continuous to the closed switch. After the time
period set by the MCU, the wetting current timer command
may be sent again to enable the timer. The user must
consider power dissipation on the device when disabling the
timer. (Refer to the paragraph entitled Temperature Monitor,
page 18.)
To increase the amount of wetting current for a switch
contact, the user has two options. Higher wetting current to a
switch may be achieved by paralleling SGn or SPn inputs.
This will increase wetting current by 16 mA for each input
added to the switch contact. The second option is to simply
add an external resistor pull-up to the VPWR supply for switch-
to-ground inputs or a resistor to ground for a switch-to-battery
input. Adding an external resistor has no effect on the
operation of the device.
Elastomeric switch contacts are made of carbon and have
a high contact resistance. Resistance of 1.0 k
Ω is common.
In applications with elastomeric switches, the pull-up and
pull-down currents must be reduced to prevent excessive
power dissipation at the contact. Programming for a lower
current settings is provided in the Functional Device
Metallic Command.
ANALOG SENSOR INPUTS (RATIOMETRIC)
The 33993 features a 22-to-1 analog multiplexer. Setting
the binary code for a specific input in the analog command
allows the microcontroller to perform analog to digital
conversion on any of the 22 inputs. On rising edge of CS the
multiplexer connects a requested input to the AMUX pin. The
AMUX pin is clamped to max of VDD volts regardless of the
higher voltages present on the input pin. After an input has
been selected as the analog, the corresponding bit in the next
SO data stream will be logic [0].
The input pin, when selected as analog, may be
configured as analog with high impedance, analog with
2.0 mA pull-up, or analog with 16 mA pull-up. Figure 13,
page 21, shows how the 33993 may be used to provide a
ratiometric reading of variable resistive input.
VDD
VPWR
VDD
SI
SO
SCLK
INT
CS
MOSI
MISO
VBAT
SP0
SP1
SP7
SG1
SG0
SG12
SG13
WAKE
33993
SCLK
CS
INT
MCU
16
2.0
VPWR VPWR
16 mA
IOC[7:0]
X
Reg
Input Capture
Timer Port
Hall-Effect
Sensor
2.5 k
Ω
mA
16
2.0
VPWR VPWR
mA
2.5 k
Ω
VBAT
mA
相关PDF资料 |
PDF描述 |
|---|---|
| RL262-222J-RC | INDUCTOR FIX 2200UH LOWPROF RAD |
| RL262-152J-RC | INDUCTOR FIX 1500UH LOWPROF RAD |
| RL262-102J-RC | INDUCTOR FIX 1000UH LOWPROF RAD |
| GBM31DCWI | CONN EDGECARD 62POS DIP .156 SLD |
| RP30-1212SE | CONV DC/DC 30W 9-18VIN 12VOUT |
相关代理商/技术参数 |
参数描述 |
|---|---|
| KIT33996EKEVB | 功能描述:电源管理IC开发工具 33996 DOSS EVAL KIT RoHS:否 制造商:Maxim Integrated 产品:Evaluation Kits 类型:Battery Management 工具用于评估:MAX17710GB 输入电压: 输出电压:1.8 V |
| KIT33999EKEVB | 功能描述:电源管理IC开发工具 33999 PDOSS EVAL KIT RoHS:否 制造商:Maxim Integrated 产品:Evaluation Kits 类型:Battery Management 工具用于评估:MAX17710GB 输入电压: 输出电压:1.8 V |
| KIT34670EGEVBE | 功能描述:电源管理IC开发工具 IEEE 802.3AF PD WITH CUR RoHS:否 制造商:Maxim Integrated 产品:Evaluation Kits 类型:Battery Management 工具用于评估:MAX17710GB 输入电压: 输出电压:1.8 V |
| KIT34671EPEVBE | 功能描述:电源管理IC开发工具 HIGH-INPUT-VOLT CHARGER RoHS:否 制造商:Maxim Integrated 产品:Evaluation Kits 类型:Battery Management 工具用于评估:MAX17710GB 输入电压: 输出电压:1.8 V |
| KIT34673EPEVBE | 功能描述:电源管理IC开发工具 IC, HIGH-INPUT-VOLT CHARGER RoHS:否 制造商:Maxim Integrated 产品:Evaluation Kits 类型:Battery Management 工具用于评估:MAX17710GB 输入电压: 输出电压:1.8 V |
发布紧急采购，3分钟左右您将得到回复。