- 您现在的位置：买卖IC网 > PDF目录15794 > KIT33993DWBEVB (Freescale Semiconductor)KIT EVAL FOR MC33993 SWITCH DET PDF资料下载
参数资料
| 型号： | KIT33993DWBEVB |
| 厂商： | Freescale Semiconductor |
| 文件页数： | 6/28页 |
| 文件大小： | 0K |
| 描述： | KIT EVAL FOR MC33993 SWITCH DET |
| 标准包装： | 1 |
| 类型： | 微控制器 |
| 适用于相关产品： | MC33993 |
| 所含物品： | 评估板、数据表和说明文档 |
第1页第2页第3页第4页第5页当前第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页
Analog Integrated Circuit Device Data
14
Freescale Semiconductor
33993
FUNCTIONAL DEVICE OPERATION
LOGIC COMMANDS AND REGISTERS
ARCHIVE
INFORMATION
ARCHIVE
INFORMATION
WETTING CURRENT TIMER REGISTER
Each switch input has a designated 20 ms timer. The timer
starts when the specific switch input crosses the comparator
threshold (4.0 V). When the 20 ms timer expires, the contact
current is reduced from 16 mA to 2.0 mA. The wetting current
timer may be disabled for a specific input. When the timer is
disabled, 16 mA of current will continue to flow through the
closed switch contact. With multiple wetting current timers
disabled, power dissipation for the IC must be considered.
The MCU may change or update the Wetting Current
Timer Register via software at any time in Normal mode. This
allows the MCU to control the amount of time wetting current
is applied to the switch contact. Programming the wetting
current timer bit to logic [0] will disable the wetting current
timer. Programming the wetting current timer bit to logic [1]
will enable the wetting current timer (refer to Table 8).
TRI-STATE REGISTER
The tri-state command is use to set the SPn or SGn input
node as high impedance (refer to Table 9). By setting the
Tri-State Register bit to logic [1], the input will be high
impedance regardless of the metallic command setting. The
comparator on each input remains active. This command
allows the use of each input as a comparator with a 4.0 V
threshold. The MCU may change or update the Tri-State
Register via software at any time in Normal mode.
ANALOG SELECT REGISTER
The analog voltage on switch inputs may be read by the
MCU using the analog command (refer to Table 10). Internal
to the IC is a 22-to-1 analog multiplexer. The voltage present
on the selected input pin is buffered and made available on
the AMUX output pin. The AMUX output pin is clamped to a
maximum of VDD volts regardless of the higher voltages
present on the input pin. After an input has been selected as
the analog, the corresponding bit in the next SO data stream
will be logic [0]. When selecting a channel to be read as
analog, the user must also set the desired current (16 mA,
2.0 mA, or high impedance). Setting bit 6 and bit 5 to 0,0
selects the input as high impedance. Setting bit 6 and bit 5 to
0,1 selects 2.0 mA, and 1,0 selects 16 mA. Setting bit 6 and
bit 5 to 1,1 in the Analog Select Register is not allowed and
will place the input as an analog input with high impedance.
Analog currents set by the analog command are pull-up
currents for all SGn and SPn inputs (refer to Table 10). The
analog command does not allow pull-down currents on the
SPn inputs. Setting the current to 16 mA or 2.0 mA may be
useful for reading sensor inputs. Further information is
provided in the Typical Applications section of this datasheet
beginning on page 20. The MCU may change or update the
Table 7. Metallic Command
Metallic Command
Command Bits
23
22
21
20
19
18
17
16
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
0
1
0
X
sp7 sp6 sp5 sp4 sp3 sp2 sp1 sp0
0
1
0
1
X
sg1
3
sg1
2
sg1
1
sg1
0
sg9 sg8 sg7 sg6 sg5 sg4 sg3 sg2 sg1 sg0
Table 8. Wetting Current Timer Enable Command
Wetting Current Timer Commands
Command Bits
23
22
21
20
19
18
17
16
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
0
1
X
sp7 sp6 sp5 sp4 sp3 sp2 sp1 sp0
0
1
0
X
sg1
3
sg1
2
sg1
1
sg1
0
sg9 sg8 sg7 sg6 sg5 sg4 sg3 sg2 sg1 sg0
Table 9. Tri-State Command
Tri-State Commands
Command Bits
23
22
21
20
19
18
17
16
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
0
1
0
1
X
sp7 sp6 sp5 sp4 sp3 sp2 sp1 sp0
0
1
0
1
0
X
sg1
3
sg1
2
sg1
1
sg1
0
sg9 sg8 sg7 sg6 sg5 sg4 sg3 sg2 sg1 sg0
相关PDF资料 |
PDF描述 |
|---|---|
| RL262-222J-RC | INDUCTOR FIX 2200UH LOWPROF RAD |
| RL262-152J-RC | INDUCTOR FIX 1500UH LOWPROF RAD |
| RL262-102J-RC | INDUCTOR FIX 1000UH LOWPROF RAD |
| GBM31DCWI | CONN EDGECARD 62POS DIP .156 SLD |
| RP30-1212SE | CONV DC/DC 30W 9-18VIN 12VOUT |
相关代理商/技术参数 |
参数描述 |
|---|---|
| KIT33996EKEVB | 功能描述:电源管理IC开发工具 33996 DOSS EVAL KIT RoHS:否 制造商:Maxim Integrated 产品:Evaluation Kits 类型:Battery Management 工具用于评估:MAX17710GB 输入电压: 输出电压:1.8 V |
| KIT33999EKEVB | 功能描述:电源管理IC开发工具 33999 PDOSS EVAL KIT RoHS:否 制造商:Maxim Integrated 产品:Evaluation Kits 类型:Battery Management 工具用于评估:MAX17710GB 输入电压: 输出电压:1.8 V |
| KIT34670EGEVBE | 功能描述:电源管理IC开发工具 IEEE 802.3AF PD WITH CUR RoHS:否 制造商:Maxim Integrated 产品:Evaluation Kits 类型:Battery Management 工具用于评估:MAX17710GB 输入电压: 输出电压:1.8 V |
| KIT34671EPEVBE | 功能描述:电源管理IC开发工具 HIGH-INPUT-VOLT CHARGER RoHS:否 制造商:Maxim Integrated 产品:Evaluation Kits 类型:Battery Management 工具用于评估:MAX17710GB 输入电压: 输出电压:1.8 V |
| KIT34673EPEVBE | 功能描述:电源管理IC开发工具 IC, HIGH-INPUT-VOLT CHARGER RoHS:否 制造商:Maxim Integrated 产品:Evaluation Kits 类型:Battery Management 工具用于评估:MAX17710GB 输入电压: 输出电压:1.8 V |
发布紧急采购，3分钟左右您将得到回复。