- 您现在的位置：买卖IC网 > PDF目录17156 > KITMPR084EVM (Freescale Semiconductor)KIT EVAL 8-PAD TOUCH MPR084 PDF资料下载
参数资料
| 型号： | KITMPR084EVM |
| 厂商： | Freescale Semiconductor |
| 文件页数： | 2/40页 |
| 文件大小： | 0K |
| 描述： | KIT EVAL 8-PAD TOUCH MPR084 |
| 标准包装： | 1 |
| 传感器类型： | 触摸，电容式 |
| 接口： | I²C |
| 电源电压： | 1.8 V ~ 3.6 V |
| 嵌入式： | 是，其它 |
| 已供物品： | 板，缆线，CD |
| 已用 IC / 零件： | MPR084 |
| 产品目录页面： | 2808 (CN2011-ZH PDF) |
| 相关产品： | MPR084EJR2CT-ND - IC CTLR TOUCH SENSR PROX 16TSSOP MPR084QR2-ND - IC CTLR TOUCH SENSOR PROX 16-QFN MPR084Q-ND - IC CTLR TOUCH SENSOR PROX 16-QFN MPR084EJR2TR-ND - IC CTLR TOUCH SENSR PROX 16TSSOP MPR084EJ-ND - IC CTLR TOUCH SENSR PROX 16TSSOP |
第1页当前第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页
MPR084
Sensors
10
Freescale Semiconductor
3
Touch Detection
3.1
Introduction
When using a capacitive touch sensor system the raw data must be filtered and interpreted. This process can be done many
different ways but the method used in the MPR084 is explained in this chapter.
3.2
Understanding the Basics
The touch pad interface has to distinguish touch status through varying user conditions (different finger sizes in bare hands or
gloves) and environmental conditions (electrical and RF noise, sensor contamination with dirt or moisture).
The touch pad circuitry reports touch status as one of the following two conditions:
1.
Touch Pad untouched
2.
Touch Pad touched on one of eight pads.
The touch pad is only touched in one position, ideally near the middle of one of the eight pads. If a touch occurs between pads,
untouched will be reported.
3.3
Conditional Output Scenarios
Since it is unlikely that in a real world case a single independent touch will occur two specific multi-touch response cases are
outlined. Methods for changing the sensitivity of the device will be discussed in another Chapter, but the important part is that the
sensitivity is determined by the strength of an input signal. If more than one input signal is above the selected sensitivity then the
touch sensor controller interprets this in a specific way. This functionality is broken down into two different cases.
3.3.1
Simultaneous Touches
Any time multiple touches are detected at the same time the touch sensor controller recognizes this case and accounts for it. The
number of allowed reported touches is settable using the Maximum Number of Touched Positions Register (Section 3.6). In the
case where this register is set to 1, all touches past the first will be ignored and unreported.
A special case is when exact 2 keys are involved in the interaction. In most cases one of the two electrodes will receive a stronger
signal than the other. If the difference in capacitance is statistically significant between the pad with the stronger signal will be
reported
This functionality is sometimes called 1-Keyed Lockout. by changing the Maximum Number of Touched Positions Register
(Section 3.6). this value can be set. Thus the n-key lockout is determined by this register.
3.3.2
Sequential Touches
Another case is when one touch pad is touched and held and a second touch pad is then touched and held. For this situation the
second touch will be ignored and the first touch will continue to be reported.
If the second touch is released before the first touch then the second touch will be completely ignored. But, if the first touch is
released before the second then the system will report that the first key is released and that the second key is now touched. This
functionality is sometimes called 2-Key Rollover.
3.4
Touch Pad Configuration Register
The Touch Pad Configuration Register configures a variety of the MPR084 features. Each of these features is described in
following sections. The I2C slave address of the Touch Pad Configuration Register is 0x03.
Figure 14. Touch Pad Configuration Register
7
6
543210
R
TPSE
0
BKA
ACE
TPRBE
TPTBE
0
TPE
W
Reset:
1
0
000001
= Unimplemented
相关PDF资料 |
PDF描述 |
|---|---|
| MIC4467ZN | IC DRIVER MOSF QUAD 1.2A 14-DIP |
| MIC4467ZWM | IC DRIVER MOSF QUAD 1.2A 16-SOIC |
| MIC4468ZWM | IC DRIVER MOSF QUAD 1.2A 16SOIC |
| ECM11DSEF | CONN EDGECARD 22POS .156 EYELET |
| C8051F560DK | KIT DEVELOPMENT FOR C8051F560 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| KITMPR121EVM | 功能描述:触摸传感器开发工具 MPR121 Sensor Tool Box RoHS:否 制造商:Cypress Semiconductor 工具用于评估: 接口类型: 工作电压: 最大工作温度: |
| KITMPR121EVM | 制造商:Freescale Semiconductor 功能描述:Sensor Toolbox Proximity Sensor Kit |
| KITMPVZ5004EVK | 功能描述:压力传感器开发工具 WATER LEVEL BOARD RoHS:否 制造商:Freescale Semiconductor 工具用于评估:MPL3115A2 接口类型:USB 最大工作温度: |
| KITMPXA6115AEVB | 功能描述:压力传感器开发工具 Sensor Toolbx Pressu Sensor Developmt brd RoHS:否 制造商:Freescale Semiconductor 工具用于评估:MPL3115A2 接口类型:USB 最大工作温度: |
| KITMPXSHOWEVK | 功能描述:压力传感器开发工具 PRESSURE SHOWBOARD RoHS:否 制造商:Freescale Semiconductor 工具用于评估:MPL3115A2 接口类型:USB 最大工作温度: |
发布紧急采购，3分钟左右您将得到回复。