- 您现在的位置：买卖IC网 > PDF目录17156 > KITMPR084EVM (Freescale Semiconductor)KIT EVAL 8-PAD TOUCH MPR084 PDF资料下载
参数资料
| 型号： | KITMPR084EVM |
| 厂商： | Freescale Semiconductor |
| 文件页数： | 39/40页 |
| 文件大小： | 0K |
| 描述： | KIT EVAL 8-PAD TOUCH MPR084 |
| 标准包装： | 1 |
| 传感器类型： | 触摸，电容式 |
| 接口： | I²C |
| 电源电压： | 1.8 V ~ 3.6 V |
| 嵌入式： | 是，其它 |
| 已供物品： | 板，缆线，CD |
| 已用 IC / 零件： | MPR084 |
| 产品目录页面： | 2808 (CN2011-ZH PDF) |
| 相关产品： | MPR084EJR2CT-ND - IC CTLR TOUCH SENSR PROX 16TSSOP MPR084QR2-ND - IC CTLR TOUCH SENSOR PROX 16-QFN MPR084Q-ND - IC CTLR TOUCH SENSOR PROX 16-QFN MPR084EJR2TR-ND - IC CTLR TOUCH SENSR PROX 16TSSOP MPR084EJ-ND - IC CTLR TOUCH SENSR PROX 16TSSOP |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页当前第39页第40页
MPR084
Sensors
8
Freescale Semiconductor
When performing read-after-write verification, remember to re-set the command byte’s address because the stored command
byte address will generally have been auto-incremented after the write (Section 2.4).
Figure 12. ‘n’ Data Bytes Received
2.3.8
Operation with Multiple Master
The application should use repeated starts to address the MPR084 to avoid bus confusion between I2C masters.On a I2C bus,
once a master issues a start/repeated start condition, that master owns the bus until a stop condition occurs. If a master that does
not own the bus attempts to take control of that bus, then improper addressing may occur. An address may always be rewritten
to fix this problem. Follow I2C protocol for multiple master configurations.
2.3.9
Device Reset
The RST is an active-low software reset. This is implemented in the Configuration Register by activating the RST bit. When
asserted, the device clears any transaction to or from the MPR084 on the serial interface and configures the internal registers to
the same state as a power-up reset (Table 4). The MPR084 then waits for a START condition on the serial interface.
The sensor controller is capable of operating down to 1.8 V, however, in order for the sensor controller to exit reset and startup
correctly the host system must initially provide 2.0 V to 3.6 V input to VDD and then follow the process in Figure 13. This process
is required in applications that require regulated operation in the 1.8 V to 2.0 V range. In the case that the application uses an
unregulated battery, then the battery must initially provide at least 2.0 V to correctly power-up the sensor controller which limits
battery selection to the 2.0 V to 3.6 V range.
Figure 13. Low Voltage (1.8 V - 2.0 V) Power-up Sequence
SAAA P
1
SLAVE ADDRESS
COMMAND BYTE
DATA BYTE
acknowledge from MPR084
R/W
nbytes
auto-increment memory
word address
D15 D14 D13 D12 D11 D10 D9 D8
D1 D0
D3 D2
D5 D4
D7 D6
Howcommand byte and data byte
map into MPR084's registers
acknowledge from
MPR084
acknowledge from
MPR084
Established Comms with
Sensor Controller?
i.e. Read from FIFO
Is Data valid? (0 x 40)
Idle Delay Loop
Apply 2.0V to VDD Max
To Sensor Controller
Lower VDD to the desired operating voltage
1.8 V to 2.0 V
False
True
相关PDF资料 |
PDF描述 |
|---|---|
| MIC4467ZN | IC DRIVER MOSF QUAD 1.2A 14-DIP |
| MIC4467ZWM | IC DRIVER MOSF QUAD 1.2A 16-SOIC |
| MIC4468ZWM | IC DRIVER MOSF QUAD 1.2A 16SOIC |
| ECM11DSEF | CONN EDGECARD 22POS .156 EYELET |
| C8051F560DK | KIT DEVELOPMENT FOR C8051F560 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| KITMPR121EVM | 功能描述:触摸传感器开发工具 MPR121 Sensor Tool Box RoHS:否 制造商:Cypress Semiconductor 工具用于评估: 接口类型: 工作电压: 最大工作温度: |
| KITMPR121EVM | 制造商:Freescale Semiconductor 功能描述:Sensor Toolbox Proximity Sensor Kit |
| KITMPVZ5004EVK | 功能描述:压力传感器开发工具 WATER LEVEL BOARD RoHS:否 制造商:Freescale Semiconductor 工具用于评估:MPL3115A2 接口类型:USB 最大工作温度: |
| KITMPXA6115AEVB | 功能描述:压力传感器开发工具 Sensor Toolbx Pressu Sensor Developmt brd RoHS:否 制造商:Freescale Semiconductor 工具用于评估:MPL3115A2 接口类型:USB 最大工作温度: |
| KITMPXSHOWEVK | 功能描述:压力传感器开发工具 PRESSURE SHOWBOARD RoHS:否 制造商:Freescale Semiconductor 工具用于评估:MPL3115A2 接口类型:USB 最大工作温度: |
发布紧急采购，3分钟左右您将得到回复。