参数资料
| 型号： | KS8001S |
| 厂商： | Micrel Inc |
| 文件页数： | 15/44页 |
| 文件大小： | 0K |
| 描述： | TXRX 10/100 LINKMD 3.3V 48-SSOP |
| 标准包装： | 30 |
| 类型： | 收发器 |
| 驱动器/接收器数： | 1/1 |
| 规程： | IEEE 802 |
| 电源电压： | 1.8 V ~ 3.3 V |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 48-BSSOP（0.295"，7.50mm 宽） |
| 供应商设备封装： | 48-SSOP |
| 包装： | 管件 |
| 配用： | KS8001L-EVAL-ND - EVAL KIT EXPERIMENTAL KS8001L |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页当前第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页
KS8001
Micrel
May 2005 – SPECIFICATIONS SUBJECT TO CHANGE WITHOUT NOTICE
KS8001
MICREL CONFIDENTIAL. DO NOT DISTRIBUTE.
22
Auto MDI/MDI-X Cross-Over Transformer Connection
KS8001 features HP Auto MDI/MDI-X crossover and requires symmetric transformers that support Auto MDI/MDI-X. See Selection
of Isolation Transformers on p. 43 for a list of transformers that support Auto MDI/MDI-X.
Power Management
The KS8001 offers the following modes for power management:
Power Down Mode: This mode can be achieved by writing to Register 0.11 or pulling pin 30 PD# Low. In the power down
state, the KS8061 disables all internal functions and drives output pins to logic zero, except for the MII serial management
interface.
Power Saving Mode: writing to register 1fh.10 can disable this mode. The KS8001 will then turn off everything except for
the Energy Detect and PLL circuits when the cable is not installed. In other words, the KS8001 will shutdown most of the
internal circuits to save power if there is no link. Power Saving mode will be in this most effective state when Auto-
Negotiation Mode is enabled.
100BT FX Mode
100BT FX mode is activated when FXSD/FXEN is higher than 0.6V (This pin has a default pull down). Under this mode, the auto-
negotiation and auto-MDIX features are disabled.
In fiber operation FXSD pin should connect to the SD (signal detect) output of the fiber module. The internal threshold of FXSD is
around
Vdd +/- 50 mV (2.2V +/- 0.05V at 3.3V). Above this level, it is considered Fiber signal detected, and the operation is
summarized in the following table:
FXSD/FXEN
Condition
Less than 0.6V
100TX mode
Less than 2.15V,
but greater than 0.6V
FX mode
No signal detected
FEF generated
Greater than 2.25V
FX mode
Signal detected
To ensure proper operation, the swing of fiber module SD should cover the threshold variation. A resistive voltage divider is
recommended to adjust the SD voltage range.
FEF (Far End Fault), repetition of a special pattern, which consists of 84-ones and 1-zero, is generated under “FX mode with no
signal detected”. The purpose of FEF is to notify the sender of a faulty link. When receiving a FEF, the LINK will go down to indicate
a fault, even with fiber signal detected. The transmitter is not affected by receiving a FEF and still sends out its normal transmit
pattern from MAC. FEF can be disabled by strapping pin27 low, please refer to “Strapping Options” section.
Media converter operation
The KS8001 is capable of performing media conversion with 2 parts in a back-to-back RMII mode as indicated in the diagram. Both
parts are in RMII mode and with RMII_BTB asserted (pin21 & 22 strapped high). One part is operating at TX mode and the other in
FX mode. Both parts can share a common 50MHz oscillator.
Under this operation, auto-Negotiation on the TX side will prohibit 10BASE-T link up. Additional options can be implemented under
this operation. Disable the transmitter and set it at tri-state by controlling the high TXD2 pin. In order to do this, RXD2 and TXD2 pins
need to be connected via an inverter. When TXD2 pin is high in both the copper and fiber operation, it disables transmit. Meanwhile,
the RXD2 pin on the copper side serves as the energy detect and can indicate if a line signal is detected. TXD3 should be tied low
and RXD3 let float. Please contact your local Micrel FAE for a Media Converter reference design.
相关PDF资料 |
PDF描述 |
|---|---|
| NB7L216MN | IC RECEIVER/DRIVER DIFF 16-QFN |
| M83723/75W10028 | CONN PLUG 2POS STRAIGHT W/SCKT |
| VI-B41-IV-B1 | CONVERTER MOD DC/DC 12V 150W |
| VI-J7Z-EY-F3 | CONVERTER MOD DC/DC 2V 20W |
| D38999/24WJ43PA | CONN RCPT 43POS JAM NUT W/PINS |
相关代理商/技术参数 |
参数描述 |
|---|---|
| KS8001S TR | 功能描述:TXRX 10/100 LINKMD 3.3V 48-SSOP RoHS:否 类别:集成电路 (IC) >> 接口 - 驱动器，接收器，收发器 系列:- 标准包装:1,140 系列:AU 类型:收发器 驱动器/接收器数:1/1 规程:CAN 电源电压:5.3 V ~ 27 V 安装类型:表面贴装 封装/外壳:14-SOIC（0.154"，3.90mm 宽） 供应商设备封装:14-SO 包装:管件 其它名称:935267940512AU5790D14AU5790D14-ND |
| KS8001SI | 功能描述:TXRX 10/100 LINKMD 3.3V 48-SSOP RoHS:否 类别:集成电路 (IC) >> 接口 - 驱动器，接收器，收发器 系列:- 标准包装:1,140 系列:AU 类型:收发器 驱动器/接收器数:1/1 规程:CAN 电源电压:5.3 V ~ 27 V 安装类型:表面贴装 封装/外壳:14-SOIC（0.154"，3.90mm 宽） 供应商设备封装:14-SO 包装:管件 其它名称:935267940512AU5790D14AU5790D14-ND |
| KS800A500-1800V Y40KSEA | 制造商:LIUJING 制造商全称:LIUJING 功能描述:可控硅、晶闸管 |
| KS800A500-1800V Y40KSE | 制造商:LIUJING 制造商全称:LIUJING 功能描述:可控硅、晶闸管 |
| KS8081 | 功能描述:IC SWITCH 10/100 3PORT 128PQFP RoHS:否 类别:集成电路 (IC) >> 专用 IC 系列:* 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:1 系列:- 类型:调帧器 应用:数据传输 安装类型:表面贴装 封装/外壳:400-BBGA 供应商设备封装:400-PBGA（27x27） 包装:散装 |
发布紧急采购，3分钟左右您将得到回复。