参数资料
| 型号： | KS8993M |
| 厂商： | Micrel Inc |
| 文件页数： | 14/85页 |
| 文件大小： | 0K |
| 描述： | IC SWITCH 10/100 3PORT 128PQFP |
| 标准包装： | 66 |
| 系列： | * |
| 类型： | * |
| 应用： | * |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 128-BFQFP |
| 供应商设备封装： | 128-PQFP（14x20） |
| 包装： | 管件 |
| 配用： | 576-1013-ND - BOARD EVAL EXPERIMENT KS8993M |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页当前第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页第73页第74页第75页第76页第77页第78页第79页第80页第81页第82页第83页第84页第85页
Micrel, Inc.
KS8993M/ML/MI
April 2005
21
M9999-041205
PLL Clock Synthesizer
The KS8993M generates 125MHz, 31.25MHz, 25MHz, and 10MHz clocks for system timing. Internal clocks are
generated from an external 25MHz crystal or oscillator.
Scrambler/De-scrambler (100BASE-TX Only)
The purpose of the scrambler is to spread the power spectrum of the signal in order to reduce EMI and baseline
wander. Transmitted data is scrambled through the use of an 11-bit wide linear feedback shift register (LFSR).
The scrambler can generate a 2047-bit non-repetitive sequence. The receiver will then de-scramble the incoming
data stream with the same sequence at the transmitter.
100BASE-FX Operation
100BASE-FX operation is very similar to 100BASE-TX operation with the differences being that the scrambler /
de-scrambler and MLT3 encoder / decoder are bypassed on transmission and reception. In 100BASE-FX mode,
the auto negotiation feature is bypassed since there is no standard that supports fiber auto negotiation. The auto-
MDI/MDI-X feature is also disabled.
100BASE-FX Signal Detection
In fiber operation, the KS8993M’s FXSD1 (fiber signal detect) input pin is usually connected to the fiber
transceiver’s SD (signal detect) output pin. 100BASE-FX mode is activated when the FXSD1 input pin is greater
than 1V. When FXSD1 is between 1V and 1.8V, no fiber signal is detected and a far end fault (FEF) is generated.
When FXSD1 is over 2.2V, the fiber signal is detected.
Alternatively, the designer may choose not to implement the FEF feature. In this case, the FXSD1 input pin is tied
high to force 100BASE-FX mode.
100BASE-FX signal detection is summarized in the following table:
Part Number
Mode
Less than 0.2V
TX mode
Greater than 1V, but less than 1.8V
FX mode
No signal detected.
Far-end fault generated
Greater than 2.2V I
FX mode
Signal detected
Table 1. FX and TX Mode Selection
To ensure proper operation, a resistive voltage divider is recommended to adjust the fiber transceiver’s SD output
voltage swing to match the KS8993M’s FXSD1 input voltage threshold.
100BASE-FX Far End Fault
An FEF occurs when the signal detection is logically false on the receive side of the fiber transceiver. The
KS8993M detects a FEF when its FXSD1 input is between 1.0V and 1.8V. When an FEF occurs, the transmission
side signals the other end of the link by sending 84 1’s followed by a zero in the idle period between frames.
Upon receiving an FEF, the LINK will go down (even when a fiber signal is detected) to indicate a fault condition.
The transmitting side is not affected when an FEF is received, and will continue to send out its normal transmit
pattern from the MAC. By default, FEF is enabled. The FEF feature can be disabled through register setting.
10BASE-T Transmit
The output 10BASE-T driver is incorporated into the 100BASE-T driver to allow transmission with the same
相关PDF资料 |
PDF描述 |
|---|---|
| ESA49DTAH | CONN EDGECARD 98POS R/A .125 SLD |
| EMA49DTAH | CONN EDGECARD 98POS R/A .125 SLD |
| LFXP20E-4F388C | IC FPGA 19.7KLUTS 268I/O 388-BGA |
| ESA49DTAD | CONN EDGECARD 98POS R/A .125 SLD |
| EMA49DTAD | CONN EDGECARD 98POS R/A .125 SLD |
相关代理商/技术参数 |
参数描述 |
|---|---|
| KS8993M_11 | 制造商:MICREL 制造商全称:Micrel Semiconductor 功能描述:Integrated 3-Port 10/100 Managed Switch with PHYs |
| KS8993MA5 | 功能描述:IC SWITCH 3-PORT 10/100 128-PQFP RoHS:否 类别:集成电路 (IC) >> 专用 IC 系列:* 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:1 系列:- 类型:调帧器 应用:数据传输 安装类型:表面贴装 封装/外壳:400-BBGA 供应商设备封装:400-PBGA（27x27） 包装:散装 |
| KS8993M-EVAL | 功能描述:BOARD EVAL EXPERIMENT KS8993M RoHS:否 类别:编程器，开发系统 >> 评估演示板和套件 系列:- 产品培训模块:Obsolescence Mitigation Program 标准包装:1 系列:- 主要目的:电源管理，电池充电器 嵌入式:否 已用 IC / 零件:MAX8903A 主要属性:1 芯锂离子电池 次要属性:状态 LED 已供物品:板 |
| KS8993MI | 功能描述:IC SWITCH 10/100 3PORT 128PQFP RoHS:否 类别:集成电路 (IC) >> 专用 IC 系列:* 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:1 系列:- 类型:调帧器 应用:数据传输 安装类型:表面贴装 封装/外壳:400-BBGA 供应商设备封装:400-PBGA（27x27） 包装:散装 |
| KS8993ML | 功能描述:IC SWITCH 10/100 3PORT 128PQFP RoHS:否 类别:集成电路 (IC) >> 专用 IC 系列:* 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:1 系列:- 类型:调帧器 应用:数据传输 安装类型:表面贴装 封装/外壳:400-BBGA 供应商设备封装:400-PBGA（27x27） 包装:散装 |
发布紧急采购，3分钟左右您将得到回复。