参数资料
| 型号： | KS8999I |
| 厂商： | Micrel Inc |
| 文件页数： | 17/52页 |
| 文件大小： | 0K |
| 描述： | IC SWITCH 9-PORT 10/100 208-PQFP |
| 标准包装： | 100 |
| 系列： | * |
| 类型： | * |
| 应用： | * |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 208-MQFP，208-PQFP |
| 供应商设备封装： | 208-PQFP（28x28） |
| 包装： | 散装 |
| 配用： | 576-1023-ND - BOARD EVAL EXPERIMENT FOR KS8999 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页当前第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页
KS8999
Micrel
KS8999
24
January 2005
MII Interface Operation
The MII (Media Independent Interface) operates in either a MAC or PHY mode. In the MAC mode, the KS8999 MII acts like
a MAC and in the PHY mode, it acts like a PHY device. This interface is specified by the IEEE 802.3 committee and provides
a common interface between physical layer and MAC layer devices. There are two distinct groups, one being for transmission
and the other for receiving. The table below describes the signals used in this interface in MAC and PHY modes.
PHY Mode Connection
MAC Mode Connection
External MAC
KS8999
External
KS8999
Controller Signals
PHY Signals
Description
PHY Signals
MAC Signals
MTXEN
Transmit enable
MTXEN
MRXDV
MTXER
Transmit error
MTXER
Not used
MTXD3
MTXD[3]
Transmit data bit 3
MTXD3
MRXD[3]
MTXD2
MTXD[2]
Transmit data bit 2
MTXD2
MRXD[2]
MTXD1
MTXD[1]
Transmit data bit 1
MTXD1
MRXD[1]
MTXD0
MTXD[0]
Transmit data bit 0
MTXD0
MRXD[0]
MTXC
Transmit clock
MTXC
MCOL
Collision detection
MCOL
MCRS
Carrier sense
MCRS
MRXDV
Receive data valid
MRXDV
SMTXEN
MRXER
Not used
Receive error
MRXER
MTXER
MRXD3
MRXD[3]
Receive data bit 3
MRXD3
MTXD[3]
MRXD2
MRXD[2]
Receive data bit 2
MRXD2
MTXD[2]
MRXD1
MRXD[1]
Receive data bit 1
MRXD1
MTXD[1]
MRXD0
MRXD[0]
Receive data bit 0
MRXD0
MTXD[0]
MRXC
Receive clock
MRXC
Table 1. MII Signals
This interface is a nibble wide data interface and therefore runs at _ the network bit rate (not encoded). Additional signals on
the transmit side indicate when data is valid or when an error occurs during transmission. Likewise, the receive side has
indicators that convey when the data is valid and without physical layer errors.
For half-duplex operation there is a signal that indicates a collision has occurred during transmission.
相关PDF资料 |
PDF描述 |
|---|---|
| KSZ8001LI TR | IC TXRX PHY 10/100 3.3V 48LQFP |
| KSZ8031RNLI | TXRX PHY 10/100 3.3V 24-QFN |
| KSZ8041MLL TR | TXRX 10/100 3.3V PHY MII 48LQFP |
| KSZ8041NLA3TR | TRANSCEIVER 10/100 32-MLF |
| KSZ8041NLJ TR | TXRX PHY 10/100 3.3V 32MLF |
相关代理商/技术参数 |
参数描述 |
|---|---|
| KS9/KSE9/59/103/115 | 制造商:PEPPERL+FUCHS 功能描述:Through beam cable sensor,PNP o/p 250mm |
| KS9~11 | 制造商:Tohodenzai 功能描述: |
| KS9~12B | 制造商:Tohodenzai 功能描述: |
| KS900A | 制造商:ALC 功能描述:ALCO CLEAR KNOB S9B6B |
| KS900A1/4 | 功能描述:旋钮和转盘 KNOB AL W/SKIRT 1/4 RoHS:否 制造商:Davies Molding 材料:Phenolic 设计:Set Screw 轴尺寸:0.25 in 直径:3/4 in 颜色:Black 指示器型式:Line |
发布紧急采购，3分钟左右您将得到回复。