- 您现在的位置：买卖IC网 > PDF目录10171 > KSZ8001S TR (Micrel Inc)TXRX 10/100 LINKMD 3.3V 48-SSOP PDF资料下载
参数资料
| 型号： | KSZ8001S TR |
| 厂商： | Micrel Inc |
| 文件页数： | 6/46页 |
| 文件大小： | 0K |
| 描述： | TXRX 10/100 LINKMD 3.3V 48-SSOP |
| 标准包装： | 1,000 |
| 类型： | 收发器 |
| 规程： | MII，RMII，SMII |
| 电源电压： | 1.8V, 3.3V |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 48-BSSOP（0.295"，7.50mm 宽） |
| 供应商设备封装： | 48-SSOP |
| 包装： | 带卷 (TR) |
| 配用： | 576-1620-ND - BOARD EVALUATION FOR KSZ8001L |
| 其它名称： | KSZ8001STR KSZ8001STR-ND |
第1页第2页第3页第4页第5页当前第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页
Micrel
KSZ8001
June 2009
Revision 1.04
14
Receive Clock (RXC)
: For 100BASE-TX links, the receive clock is continuously recovered from the line. If the link goes down, and
auto-negotiation is disabled, the receive clock then operates off the master input clock (X1 or TXC). For 10BASE-T links, the receive
clock is recovered from the line while carrier is active, and operates from the master input clock when the line is idle. The KSZ8001
synchronizes the receive data and control signals on the falling edge of RXC in order to stabilize the signals at the rising edge of the
clock with 10ns setup and hold times.
Transmit Enable
: The MAC must assert TXEN at the same time as the first nibble of the preamble, and de-assert TXEN after the
last bit of the packet.
Receive Data Valid
: The KSZ8001 asserts RXDV when it receives a valid packet. Line operating speed and MII mode will
determine timing changes in the following way:
For 100BASE-TX link with the MII in 4B mode, RXDV is asserted from the first nibble of the preamble to the last nibble of
the data packet.
For 10BASE-T links, the entire preamble is truncated. RXDV is asserted with the first nibble of the SFD “ 5D” and remains
asserted until the end of the packet.
Error Signals
: Whenever the KSZ8001 receives an error symbol from the network, it asserts RXER and drives “1110” (4B) on the
RXD pins. When the MAC asserts TXER, the KSZ8001 will drive “H” symbols (a Transmit Error define in the IEEE 802.3 4B/5B
code group) out on the line to force signaling errors.
Carrier Sense (CRS)
: For 100TX links, a start-of-stream delimiter, or /J/K symbol pair causes assertion of Carrier Sense (CRS).
An end-of-stream delimiter, or /T/R symbol pair causes de-assertion of CRS. The PMA layer will also de-assert CRS if IDLE
symbols are received without /T/R, yet in this case RXER will be asserted for one clock cycle when CRS is de-asserted. For 10T
links, CRS assertion is based on reception of valid preamble, and de-assertion on reception of an end-of-frame (EOF) marker.
Collision
: Whenever the line state is half-duplex and the transmitter and receiver are active at the same time, then the KSZ8001
asserts its collision signal, which is asynchronous to any clock.
RMII (Reduced MII) Data Interface
RMII interface specifies a low pin count (Reduced) Media Independent Interface (RMII) intended for use between Ethernet PHYs and
Switch or Repeater ASICs. It is fully compliant with IEEE 802.3u [2].
This interface has the following characteristics:
It is capable of supporting 10Mb/s and 100Mb/s data rates
A single clock reference is sourced from the MAC to PHY (or from an external source)
It provides independent 2 bit wide (di-bit) transmit and receive data paths
It uses TTL signal levels, compatible with common digital CMOS ASIC processes
RMII Signal Definition
Signal Name
Direction
(with respect to
the PHY)
Direction
(with respect to
the MAC)
Use
REF_CLK
Input
Input or Output
Synchronous clock reference for receive, transmit and control
interface
CRS_DV
Output
Input
Carrier Sense/Receive Data Valid
RXD[1:0]
Output
Input
Receive Data
TX_EN
Input
Output
Transit Enable
TXD[1:0]
Input
Output
Transit Data
RX_ER
Output
Input
(Not Required)
Receive Error
Note:
Unused MII signals, TXD[3:2], TXER need to be tied to GND when RMII is used
相关PDF资料 |
PDF描述 |
|---|---|
| IDT72241L15J | IC FIFO 2048X18 SYNC 15NS 32PLCC |
| LTC1282ACSW#TRPBF | IC A/D CONV SAMPLING W/REF24SOIC |
| MS27467T19A35P | CONN PLUG 66POS STRAIGHT W/PINS |
| LTC1282ACSW#TR | IC ADC 12BIT SAMPLING REF 24SOIC |
| VE-B5H-IV-S | CONVERTER MOD DC/DC 52V 150W |
相关代理商/技术参数 |
参数描述 |
|---|---|
| KSZ801S | 制造商:MICREL 制造商全称:Micrel Semiconductor 功能描述:1.8C, 3.3V 10/100BASE-T/TX/FX Physical Layer Transceiver |
| KSZ8021RNL | 功能描述:TXRX PHY 100BASE TX 3.3V 24QFN RoHS:是 类别:集成电路 (IC) >> 接口 - 驱动器，接收器，收发器 系列:- 标准包装:1,140 系列:AU 类型:收发器 驱动器/接收器数:1/1 规程:CAN 电源电压:5.3 V ~ 27 V 安装类型:表面贴装 封装/外壳:14-SOIC（0.154"，3.90mm 宽） 供应商设备封装:14-SO 包装:管件 其它名称:935267940512AU5790D14AU5790D14-ND |
| KSZ8021RNL TR | 功能描述:以太网 IC 3.3V, 100Base-FX Physical Layer Transceiver with RMII support (24-QFN) RoHS:否 制造商:Micrel 产品:Ethernet Switches 收发器数量:2 数据速率:10 Mb/s, 100 Mb/s 电源电压-最大:1.25 V, 3.45 V 电源电压-最小:1.15 V, 3.15 V 最大工作温度:+ 85 C 封装 / 箱体:QFN-64 封装:Tray |
| KSZ8021RNL-EVAL | 功能描述:以太网开发工具 3.3V, 100Base-FX Physical Layer Transceiver w/ RMII Support - Evaluation Board RoHS:否 制造商:Micrel 产品:Evaluation Boards 类型:Ethernet Transceivers 工具用于评估:KSZ8873RLL 接口类型:RMII 工作电源电压: |
| KSZ8021RNL-TR | 功能描述:1/1 Transceiver Full RMII 24-QFN (4x4) 制造商:microchip technology 系列:- 包装:剪切带（CT） 零件状态:过期 类型:收发器 协议:RMII 驱动器/接收器数:1/1 双工:全 接收器滞后:- 数据速率:- 电压 - 电源:1.8V，2.5V，3.3V 工作温度:0°C ~ 70°C 安装类型:表面贴装 封装/外壳:24-VFQFN 裸露焊盘 供应商器件封装:24-QFN（4x4） 标准包装:1 |
发布紧急采购，3分钟左右您将得到回复。