参数资料
| 型号： | KSZ8041RNL |
| 厂商： | Micrel Inc |
| 文件页数： | 18/54页 |
| 文件大小： | 0K |
| 描述： | TXRX 10/100 3.3V PHY RMII 32-MLF |
| 标准包装： | 640 |
| 类型： | 收发器 |
| 驱动器/接收器数： | 1/1 |
| 规程： | RMII |
| 电源电压： | 3.135 V ~ 3.465 V |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 32-VFQFN 裸露焊盘，32-MLF? |
| 供应商设备封装： | 32-MLF?（5x5） |
| 包装： | 托盘 |
| 配用： | 576-3863-ND - BOARD EVALUATION FOR KSZ8041RNL |
| 其它名称： | 576-3503 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页当前第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页
Micrel, Inc.
KSZ8041NL/RNL
September 2010
25
M9999-090910-1.4
Receive Data Valid (RXDV)
RXDV is driven by the PHY to indicate that the PHY is presenting recovered and decoded nibbles on RXD[3:0].
In 10Mbps mode, RXDV is asserted with the first nibble of the SFD (Start of Frame Delimiter), “5D”, and remains
asserted until the end of the frame.
In 100Mbps mode, RXDV is asserted from the first nibble of the preamble to the last nibble of the frame.
RXDV transitions synchronously with respect to RXC.
Receive Data [3:0] (RXD[3:0])
RXD[3:0] transitions synchronously with respect to RXC. For each clock period in which RXDV is asserted, RXD[3:0]
transfers a nibble of recovered data from the PHY.
Receive Error (RXER)
RXER is asserted for one or more RXC periods to indicate that a Symbol Error (e.g. a coding error that a PHY is capable
of detecting, and that may otherwise be undetectable by the MAC sub-layer) was detected somewhere in the frame
presently being transferred from the PHY.
RXER transitions synchronously with respect to RXC. While RXDV is de-asserted, RXER has no effect on the MAC.
Carrier Sense (CRS)
CRS is asserted and de-asserted as follows:
In 10Mbps mode, CRS assertion is based on the reception of valid preambles. CRS de-assertion is based on the
reception of an end-of-frame (EOF) marker.
In 100Mbps mode, CRS is asserted when a start-of-stream delimiter, or /J/K symbol pair is detected. CRS is de-
asserted when an end-of-stream delimiter, or /T/R symbol pair is detected. Additionally, the PMA layer de-asserts
CRS if IDLE symbols are received without /T/R.
Collision (COL)
COL is asserted in half-duplex mode whenever the transmitter and receiver are simultaneously active on the line. This is
used to inform the MAC that a collision has occurred during its transmission to the PHY.
COL transitions asynchronously with respect to TXC and RXC.
Reduced MII (RMII) Data Interface
The Reduced Media Independent Interface (RMII) specifies a low pin count Media Independent Interface (MII). It provides
a common interface between physical layer and MAC layer devices, and has the following key characteristics:
Supports 10Mbps and 100Mbps data rates.
Uses a 50MHz reference clock.
Provides independent 2-bit wide (di-bit) transmit and receive data paths.
Contains two distinct groups of signals: one for transmission and the other for reception.
The KSZ8041NL is configured in RMII mode after it is power-up or reset with the following:
A 50MHz reference clock connected to REFCLK (pin 9).
CONFIG[2:0] (pins 18, 29, 28) set to ‘001’.
The KSZ8041RNL is configured in RMII mode and outputs the 50MHz RMII reference clock to the MAC on REF_CLK (pin
19) after it is power-up or reset with the following:
A 25MHz crystal connected to XI (pin 9) and XO (pin 8), or a 25MHz reference clock connected to XI (pin 9).
CONFIG[2:0] (pins 18, 29, 28) set to ‘001’.
In RMII mode, unused MII signals, TXD[3:2] (pins 27, 26), are tied to ground.
相关PDF资料 |
PDF描述 |
|---|---|
| KSZ8041TLI TR | IC ETHERNET PHY IND 48TQFP |
| KSZ8051MLL TR | TXRX PHY 10/T100 3.3V MII 48LQFP |
| KSZ8051MLLI TR | TXRX PHY 10/T100 3.3V MII 48LQFP |
| KSZ8051MNLI | TXRX PHY 10/T100 3.3V 32QFN |
| KSZ8051RNLI TR | TXRX PHY 10/T100 3.3V RMII 32QFN |
相关代理商/技术参数 |
参数描述 |
|---|---|
| KSZ8041RNL TR | 功能描述:以太网 IC 3.3V, 10Base-T/100Base-TX Physical Layer Transceiver with RMII Support - Lead Free RoHS:否 制造商:Micrel 产品:Ethernet Switches 收发器数量:2 数据速率:10 Mb/s, 100 Mb/s 电源电压-最大:1.25 V, 3.45 V 电源电压-最小:1.15 V, 3.15 V 最大工作温度:+ 85 C 封装 / 箱体:QFN-64 封装:Tray |
| KSZ8041RNL-EVAL | 功能描述:以太网开发工具 3.3V, 10Base-T/100Base-TX Physical Layer Transceiver with RMII Support - Evaluation Board RoHS:否 制造商:Micrel 产品:Evaluation Boards 类型:Ethernet Transceivers 工具用于评估:KSZ8873RLL 接口类型:RMII 工作电源电压: |
| KSZ8041RNLI | 制造商:MICREL 制造商全称:Micrel Semiconductor 功能描述:10Base-T/100Base-TX Physical Layer Transceiver |
| KSZ8041RNLI TR | 功能描述:以太网 IC 3.3V, 10Base-T/100Base-TX Physical Layer Transceiver with RMII Support (Industrial grade) RoHS:否 制造商:Micrel 产品:Ethernet Switches 收发器数量:2 数据速率:10 Mb/s, 100 Mb/s 电源电压-最大:1.25 V, 3.45 V 电源电压-最小:1.15 V, 3.15 V 最大工作温度:+ 85 C 封装 / 箱体:QFN-64 封装:Tray |
| KSZ8041RNLI TR-SAMPLE | 制造商:Micrel Inc 功能描述: |
发布紧急采购，3分钟左右您将得到回复。