- 您现在的位置：买卖IC网 > PDF目录16863 > KSZ8051MNL-EVAL (Micrel Inc)BOARD EVALUATION FOR KSZ8051MNL PDF资料下载
参数资料
| 型号： | KSZ8051MNL-EVAL |
| 厂商： | Micrel Inc |
| 文件页数： | 11/59页 |
| 文件大小： | 0K |
| 描述： | BOARD EVALUATION FOR KSZ8051MNL |
| 标准包装： | 1 |
| 主要目的： | 接口，以太网 PHY |
| 嵌入式： | 否 |
| 已用 IC / 零件： | KSZ8051MNL |
| 已供物品： | 板 |
| 相关产品： | 576-3845-ND - TXRX PHY 10/T100 3.3V 32QFN 576-3777-6-ND - TXRX PHY 10/T100 3.3V MII 32-QFN 576-3777-1-ND - TXRX PHY 10/T100 3.3V MII 32-QFN 576-3777-2-ND - TXRX PHY 10/T100 3.3V MII 32-QFN 576-3732-ND - TXRX PHY 10/T100 3.3V MII 32-QFN |
| 其它名称： | 576-3865 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页当前第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页
Micrel, Inc.
KSZ8051MNL/RNL
July 2010
19
M9999-070910-1.0
Functional Description: 10Base-T/100Base-TX Transceiver
The KSZ8051MNL/RNL is an integrated single 3.3V supply Fast Ethernet transceiver. It is fully compliant with the IEEE
802.3 Specification, and reduces board cost and simplifies board layout by using on-chip termination resistors for the two
differential pairs and by integrating the regulator to supply the 1.2V core.
On the copper media side, the KSZ8051MNL/RNL supports 10Base-T and 100Base-TX for transmission and reception of
data over a standard CAT-5 unshielded twisted pair (UTP) cable, and HP auto MDI/MDI-X for reliable detection of and
correction for straight-through and crossover cables.
On the MAC processor side, the KSZ8051MNL offers the Media Independent Interface (MII) and the KSZ8051RNL offers
the Reduced Media Independent Interface (RMII) for direct connection with MII/RMII compliant Ethernet MAC processors
and switches.
The MII management bus option gives the MAC processor complete access to the KSZ8051MNL/RNL control and status
registers. Additionally, an interrupt pin eliminates the need for the processor to poll for PHY status change.
100Base-TX Transmit
The 100Base-TX transmit function performs parallel-to-serial conversion, 4B/5B encoding, scrambling, NRZ-to-NRZI
conversion, and MLT3 encoding and transmission.
The circuitry starts with a parallel-to-serial conversion, which converts the MII data from the MAC into a 125MHz serial bit
stream. The data and control stream is then converted into 4B/5B coding and followed by a scrambler. The serialized data
is further converted from NRZ-to-NRZI format, and then transmitted in MLT3 current output. The output current is set by
an external 6.49k
Ω 1% resistor for the 1:1 transformer ratio.
The output signal has a typical rise/fall time of 4ns and complies with the ANSI TP-PMD standard regarding amplitude
balance, overshoot, and timing jitter. The wave-shaped 10Base-T output is also incorporated into the 100Base-TX
transmitter.
100Base-TX Receive
The 100Base-TX receiver function performs adaptive equalization, DC restoration, MLT3-to-NRZI conversion, data and
clock recovery, NRZI-to-NRZ conversion, de-scrambling, 4B/5B decoding, and serial-to-parallel conversion.
The receiving side starts with the equalization filter to compensate for inter-symbol interference (ISI) over the twisted pair
cable. Since the amplitude loss and phase distortion is a function of the cable length, the equalizer must adjust its
characteristics to optimize performance. In this design, the variable equalizer makes an initial estimation based on
comparisons of incoming signal strength against some known cable characteristics, and then tunes itself for optimization.
This is an ongoing process and self-adjusts against environmental changes such as temperature variations.
Next, the equalized signal goes through a DC restoration and data conversion block. The DC restoration circuit is used to
compensate for the effect of baseline wander and to improve the dynamic range. The differential data conversion circuit
converts the MLT3 format back to NRZI. The slicing threshold is also adaptive.
The clock recovery circuit extracts the 125MHz clock from the edges of the NRZI signal. This recovered clock is then used
to convert the NRZI signal into the NRZ format. This signal is sent through the de-scrambler followed by the 4B/5B
decoder. Finally, the NRZ serial data is converted to the MII format and provided as the input data to the MAC.
10Base-T Transmit
The 10Base-T drivers are incorporated with the 100Base-TX drivers to allow for transmission using the same magnetic.
The drivers perform internal wave-shaping and pre-emphasis, and output 10Base-T signals with a typical amplitude of
2.5V peak. The 10Base-T signals have harmonic contents that are at least 27dB below the fundamental frequency when
driven by an all-ones Manchester-encoded signal.
10Base-T Receive
On the receive side, input buffer and level detecting squelch circuits are employed. A differential input receiver circuit and
a PLL performs the decoding function. The Manchester-encoded data stream is separated into clock signal and NRZ data.
A squelch circuit rejects signals with levels less than 400 mV or with short pulse widths to prevent noise at the RXP and
RXM inputs from falsely trigger the decoder. When the input exceeds the squelch limit, the PLL locks onto the incoming
signal and the KSZ8051MNL/RNL decodes a data frame. The receive clock is kept active during idle periods in between
data reception.
相关PDF资料 |
PDF描述 |
|---|---|
| H6PPS-1018M | DIP CABLE - HDP10S/AE10M/HDP10S |
| ESC07DRYH-S93 | CONN EDGECARD 14POS DIP .100 SLD |
| TAT-125-3/4-0-STK | HEATSHRINK DUAL WALL 3/4"X4' BLK |
| V110B24E150B3 | CONVERTER MOD DC/DC 24V 150W |
| ESC12DRXN-S734 | CONN EDGECARD 24POS DIP .100 SLD |
相关代理商/技术参数 |
参数描述 |
|---|---|
| KSZ8051MNLI | 功能描述:TXRX PHY 10/T100 3.3V 32QFN RoHS:是 类别:集成电路 (IC) >> 接口 - 驱动器，接收器，收发器 系列:- 标准包装:1,140 系列:AU 类型:收发器 驱动器/接收器数:1/1 规程:CAN 电源电压:5.3 V ~ 27 V 安装类型:表面贴装 封装/外壳:14-SOIC（0.154"，3.90mm 宽） 供应商设备封装:14-SO 包装:管件 其它名称:935267940512AU5790D14AU5790D14-ND |
| KSZ8051MNLI TR | 功能描述:以太网 IC 3.3V, 10Base-T/100Base-TX Physical Layer Transceiver with MII support (32-QFN, Industrial Grade) RoHS:否 制造商:Micrel 产品:Ethernet Switches 收发器数量:2 数据速率:10 Mb/s, 100 Mb/s 电源电压-最大:1.25 V, 3.45 V 电源电压-最小:1.15 V, 3.15 V 最大工作温度:+ 85 C 封装 / 箱体:QFN-64 封装:Tray |
| KSZ8051MNLITR | 制造商:Micrel 功能描述:Ethernet TXRX PHY 10 T100 3.3V 32 QFN |
| KSZ8051MNLI-TR | 功能描述:1/1 Transceiver Full MII 32-QFN (5x5) 制造商:microchip technology 系列:- 包装:剪切带（CT） 零件状态:过期 类型:收发器 协议:MII 驱动器/接收器数:1/1 双工:全 接收器滞后:- 数据速率:- 电压 - 电源:1.8V，2.5V，3.3V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:32-VFQFN 裸露焊盘 供应商器件封装:32-QFN（5x5） 标准包装:1 |
| KSZ8051MNL-TR | 功能描述:1/1 Transceiver Full MII 32-QFN (5x5) 制造商:microchip technology 系列:- 包装:剪切带（CT） 零件状态:过期 类型:收发器 协议:MII 驱动器/接收器数:1/1 双工:全 接收器滞后:- 数据速率:- 电压 - 电源:1.8V，2.5V，3.3V 工作温度:0°C ~ 70°C 安装类型:表面贴装 封装/外壳:32-VFQFN 裸露焊盘 供应商器件封装:32-QFN（5x5） 标准包装:1 |
发布紧急采购，3分钟左右您将得到回复。