- 您现在的位置：买卖IC网 > PDF目录16855 > KSZ8851-16MLL-EVAL (Micrel Inc)BOARD EVALUATION KSZ8851-16MLL PDF资料下载
参数资料
| 型号： | KSZ8851-16MLL-EVAL |
| 厂商： | Micrel Inc |
| 文件页数： | 6/84页 |
| 文件大小： | 0K |
| 描述： | BOARD EVALUATION KSZ8851-16MLL |
| 产品培训模块： | KSZ8851 10/100 Embedded Controllers |
| 标准包装： | 1 |
| 系列： | LinkMD® |
| 主要目的： | 接口，以太网控制器（PHY 和 MAC） |
| 嵌入式： | 否 |
| 已用 IC / 零件： | KSZ8851-16MLL |
| 主要属性： | 1 个端口，100BASE-TX/10BASE-T |
| 次要属性： | 8/16 位接口，LinkMD 线缆诊断 |
| 已供物品： | 板，文档 |
| 产品目录页面： | 1081 (CN2011-ZH PDF) |
| 相关产品： | 576-3438-ND - IC CTLR MAC/PHY NON PCI 128PQFP 576-3253-ND - IC CTLR MAC/PHY NON-PCI 128-PQFP 576-3252-ND - IC CTLR MAC/PHY NON-PCI 48-LQFP |
| 其它名称： | 576-3292 |
第1页第2页第3页第4页第5页当前第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页第73页第74页第75页第76页第77页第78页第79页第80页第81页第82页第83页第84页
Micrel, Inc.
KSZ8851-16MLL/MLLI
March 11, 2014
14
Revision 2.2
Functional Description
The KSZ8851-16MLL is a single-chip Fast Ethernet MAC/PHY controller consisting of a 10/100 physical layer transceiver
(PHY), a MAC, and a Bus Interface Unit (BIU) that controls the KSZ8851-16MLL via an 8-bit or 16-bit host bus interface.
The KSZ8851-16MLL is fully compliant to IEEE802.3u standards.
Functional Overview
Power Management
The KSZ8851-16MLL supports enhanced power management feature in low power state with energy detection to ensure
low-power dissipation during device idle periods. There are four operation modes under the power management function
which is controlled by two bits in PMECR (0xD4) register as shown below:
PMECR[1:0] = 00 Normal Operation Mode
PMECR[1:0] = 01 Energy Detect Mode
PMECR[1:0] = 10 Soft Power-down mode
PMECR[1:0] = 11 Power-saving mode
Table 1 indicates all internal function blocks status under four different power management operation modes.
KSZ8851-16MLL
Function Blocks
Power Management Operation Modes
Normal Mode
Power-saving mode
Energy Detect Mode
Soft Power-Down Mode
Internal PLL Clock
Enabled
Disabled
Tx/Rx PHY
Enabled
Rx unused block disabled
Energy detect at Rx
Disabled
MAC
Enabled
Disabled
Host Interface
Enabled
Disabled
Table 1. Internal Function Blocks Status
Normal Operation Mode
This is the default setting bit[1:0]=00 in PMECR register after the chip power-up or hardware reset (pin 67). When
KSZ8851-16MLL is in this normal operation mode, all PLL clocks are running, PHY and MAC are on and the host
interface is ready for CPU read or write.
During the normal operation mode, the host CPU can set the bit[1:0] in PMECR register to transit the current normal
operation mode to any one of the other three power management operation modes.
Energy Detect Mode
The energy detect mode provides a mechanism to save more power than in the normal operation mode when the
KSZ8851-16MLL is not connected to an active link partner. For example, if cable is not present or it is connected to a
powered down partner, the KSZ8851-16MLL can automatically enter to the low power state in energy detect mode. Once
activity resumes due to plugging a cable or attempting by the far end to establish link, the KSZ8851-16MLL can
automatically power up to normal power state in energy detect mode.
Energy detect mode consists of two states, normal power state and low power state. While in low power state, the
KSZ8851-16MLL reduces power consumption by disabling all circuitry except the energy detect circuitry of the receiver.
The energy detect mode is entered by setting bit[1:0]=01 in PMECR register. When the KSZ8851-16MLL is in this mode, it
will monitor the cable energy. If there is no energy on the cable for a time longer than pre-configured value at bit[7:0] Go-
Sleep time in GSWUTR register, KSZ8851-16MLL will go into a low power state. When KSZ8851-16MLL is in low power
state, it will keep monitoring the cable energy. Once the energy is detected from the cable and is continuously presented
for a time longer than pre-configured value at bit[15:8] Wake-Up time in GSWUTR register, the KSZ8851-16MLL will enter
either the normal power state if the auto-wakeup enable bit[7] is set in PMECR register or the normal operation mode if
both auto-wakeup enable bit[7] and wakeup to normal operation mode bit[6] are set in PMECR register.
相关PDF资料 |
PDF描述 |
|---|---|
| MLF2012DR15M | INDUCTOR MULTILAYER .15UH 0805 |
| 0210491067 | CABLE JUMPER 1.25MM .203M 35POS |
| MLF2012A4R7M | INDUCTOR MULTILAYER 4.7UH 0805 |
| RNF-100-3/16-BK-STK | HEATSHRINK RNF-100 3/16"X4' BLK |
| EVAL-ADF4158EB1Z | BOARD EVALUATION FOR ADF4158 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| KSZ8851-16MLL-EVAL | 制造商:Micrel Inc 功能描述:BOARD EVALUATION FOR KSZ8851-16MLL |
| KSZ8851-16MLLI | 功能描述:以太网 IC 10/100BT Ethernet MAC + PHY with Generic (8, 16-bit) Bus Interface (I-Temp, Lead Free) RoHS:否 制造商:Micrel 产品:Ethernet Switches 收发器数量:2 数据速率:10 Mb/s, 100 Mb/s 电源电压-最大:1.25 V, 3.45 V 电源电压-最小:1.15 V, 3.15 V 最大工作温度:+ 85 C 封装 / 箱体:QFN-64 封装:Tray |
| KSZ8851-16MLLI TR | 功能描述:以太网 IC 10/100BT Ethernet MAC + PHY with Generic (8, 16-bit) Bus Interface (I-Temp, Lead Free) RoHS:否 制造商:Micrel 产品:Ethernet Switches 收发器数量:2 数据速率:10 Mb/s, 100 Mb/s 电源电压-最大:1.25 V, 3.45 V 电源电压-最小:1.15 V, 3.15 V 最大工作温度:+ 85 C 封装 / 箱体:QFN-64 封装:Tray |
| KSZ8851-16MLLJ | 功能描述:以太网 IC Single-Port Ethernet MAC Controller with 8/16-Bit Non-PCI Interface (125C support) RoHS:否 制造商:Micrel 产品:Ethernet Switches 收发器数量:2 数据速率:10 Mb/s, 100 Mb/s 电源电压-最大:1.25 V, 3.45 V 电源电压-最小:1.15 V, 3.15 V 最大工作温度:+ 85 C 封装 / 箱体:QFN-64 封装:Tray |
| KSZ8851-16MLLJ_10 | 制造商:MICREL 制造商全称:Micrel Semiconductor 功能描述:Single-Port Ethernet MAC Controller with 8-Bit or 16-Bit Non-PCI Interface |
发布紧急采购，3分钟左右您将得到回复。