- 您现在的位置：买卖IC网 > PDF目录11595 > KSZ8851-16MLL (Micrel Inc)IC CTLR MAC/PHY NON-PCI 48-LQFP PDF资料下载
参数资料
| 型号： | KSZ8851-16MLL |
| 厂商： | Micrel Inc |
| 文件页数： | 14/84页 |
| 文件大小： | 0K |
| 描述： | IC CTLR MAC/PHY NON-PCI 48-LQFP |
| 产品培训模块： | KSZ8851 10/100 Embedded Controllers |
| 标准包装： | 250 |
| 控制器类型： | 以太网控制器，MAC/PHY |
| 接口： | 总线 |
| 电源电压： | 1.8V，2.5V，3.3V |
| 工作温度： | 0°C ~ 70°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 48-LQFP |
| 供应商设备封装： | 48-LQFP（7x7） |
| 包装： | 托盘 |
| 产品目录页面： | 1081 (CN2011-ZH PDF) |
| 配用： | 576-3292-ND - BOARD EVALUATION KSZ8851-16MLL |
| 其它名称： | 576-3252 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页当前第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页第73页第74页第75页第76页第77页第78页第79页第80页第81页第82页第83页第84页
Micrel, Inc.
KSZ8851-16MLL/MLLI
March 11, 2014
21
Revision 2.2
LinkMD
Cable Diagnostics
The KSZ8851-16MLL LinkMD
uses time domain reflectometry (TDR) to analyze the cabling plant for common cabling
problems such as open circuits, short circuits, and impedance mismatches.
LinkMD
works by sending a pulse of known amplitude and duration down the MDI and MDI-X pairs and then analyzes
the shape of the reflected signal. Timing the pulse duration gives an indication of the distance to the cabling fault with a
maximum distance of 200m and an accuracy of ±2m. Internal circuitry displays the TDR information in a user-readable
digital format in register P1SCLMD[8:0].
Note: cable diagnostics are only valid for copper connections – fiber-optic operation is not supported.
Access
LinkMD
is initiated by accessing register P1SCLMD, the PHY special control/status & LinkMD register (0xF4).
Usage
LinkMD
can be run at any time by ensuring that Auto-MDIX has been disabled. To disable Auto-MDIX, write a ‘1’ to
P1CR[10] to enable manual control over the pair used to transmit the LinkMD
pulse. The self-clearing cable diagnostic
test enable bit, P1SCLMD [12], is set to ‘1’ to start the test on this pair.
When bit P1SCLMD[12] returns to ‘0’, the test is complete. The test result is returned in bits P1SCLMD[14:13] and the
distance is returned in bits P1SCLMD[8:0]. The cable diagnostic test results are as follows:
00 = Valid test, normal condition
01 = Valid test, open circuit in cable
10 = Valid test, short circuit in cable
11 = Invalid test, LinkMD
failed
If P1SCLMD[14:13]=11, this indicates an invalid test, and occurs when the KSZ8851-16MLL is unable to shut down the
link partner. In this instance, the test is not run, as it is not possible for the KSZ8851-16MLL to determine if the detected
signal is a reflection of the signal generated or a signal from another source.
Cable distance can be approximated by the following formula:
P1SCLMD[8:0] x 0.4m for port 1 cable distance
This constant may be calibrated for different cabling conditions, including cables with a velocity of propagation that varies
significantly from the norm.
Media Access Control (MAC) Operation
The KSZ8851-16MLL strictly abides by IEEE 802.3 standards to maximize compatibility.
Inter Packet Gap (IPG)
If a frame is successfully transmitted, then the minimum 96-bit time for IPG is measured between two consecutive
packets. If the current packet is experiencing collisions, the minimum 96-bit time for IPG is measured from carrier sense
(CRS) to the next transmit packet.
Back-Off Algorithm
The KSZ8851-16MLL implements the IEEE standard 802.3 binary exponential back-off algorithm in half-duplex mode.
After 16 collisions, the packet is dropped.
Late Collision
If a transmit packet experiences collisions after 512 bit times of the transmission, the packet is dropped.
Flow Control
The KSZ8851-16MLL supports standard 802.3x flow control frames on both transmit and receive sides.
On the receive side, if the KSZ8851-16MLL receives a pause control frame, the KSZ8851-16MLL will not transmit the next
normal frame until the timer, specified in the pause control frame, expires. If another pause frame is received before the
current timer expires, the timer will be updated with the new value in the second pause frame. During this period (while it
is flow controlled), only flow control packets from the KSZ8851-16MLL are transmitted.
相关PDF资料 |
PDF描述 |
|---|---|
| KSZ8873RLL | IC ETHERNET SWITCH 3PORT 64-LQFP |
| KSZ8851-16MQLI | IC CTLR MAC/PHY NON-PCI 128-PQFP |
| KSZ8851-16MQL | IC CTLR MAC/PHY NON-PCI 128-PQFP |
| LTC4278CDKD#PBF | IC PD IEEE 802.3AT 25.5W 32-DFN |
| KSZ8873MLL | IC ETHERNET SWITCH 3PORT 64-LQFP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| KSZ8851-16MLL TR | 功能描述:以太网 IC Single Ethernet Port + Generic (16-bit) Bus Interface(Lead Free) RoHS:否 制造商:Micrel 产品:Ethernet Switches 收发器数量:2 数据速率:10 Mb/s, 100 Mb/s 电源电压-最大:1.25 V, 3.45 V 电源电压-最小:1.15 V, 3.15 V 最大工作温度:+ 85 C 封装 / 箱体:QFN-64 封装:Tray |
| KSZ8851-16MLL-EVAL | 功能描述:以太网开发工具 Single Ethernet Port + Generic (16-bit) Bus Interface(Lead Free) Eval Board RoHS:否 制造商:Micrel 产品:Evaluation Boards 类型:Ethernet Transceivers 工具用于评估:KSZ8873RLL 接口类型:RMII 工作电源电压: |
| KSZ8851-16MLL-EVAL | 制造商:Micrel Inc 功能描述:BOARD EVALUATION FOR KSZ8851-16MLL |
| KSZ8851-16MLLI | 功能描述:以太网 IC 10/100BT Ethernet MAC + PHY with Generic (8, 16-bit) Bus Interface (I-Temp, Lead Free) RoHS:否 制造商:Micrel 产品:Ethernet Switches 收发器数量:2 数据速率:10 Mb/s, 100 Mb/s 电源电压-最大:1.25 V, 3.45 V 电源电压-最小:1.15 V, 3.15 V 最大工作温度:+ 85 C 封装 / 箱体:QFN-64 封装:Tray |
| KSZ8851-16MLLI TR | 功能描述:以太网 IC 10/100BT Ethernet MAC + PHY with Generic (8, 16-bit) Bus Interface (I-Temp, Lead Free) RoHS:否 制造商:Micrel 产品:Ethernet Switches 收发器数量:2 数据速率:10 Mb/s, 100 Mb/s 电源电压-最大:1.25 V, 3.45 V 电源电压-最小:1.15 V, 3.15 V 最大工作温度:+ 85 C 封装 / 箱体:QFN-64 封装:Tray |
发布紧急采购，3分钟左右您将得到回复。