参数资料
| 型号： | KSZ8864RMNI |
| 厂商： | Micrel Inc |
| 文件页数： | 29/111页 |
| 文件大小： | 0K |
| 描述： | IC ETHERNET SWITCH 4PORT 64QFN |
| 特色产品： | KSZ8864RMN Ethernet Switches |
| 标准包装： | 348 |
| 系列： | * |
| 其它名称： | 576-3995 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页当前第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页第73页第74页第75页第76页第77页第78页第79页第80页第81页第82页第83页第84页第85页第86页第87页第88页第89页第90页第91页第92页第93页第94页第95页第96页第97页第98页第99页第100页第101页第102页第103页第104页第105页第106页第107页第108页第109页第110页第111页
Micrel, Inc.
KSZ8864RMN
April 2012
24
M9999-043012-1.5
On-Chip Termination Resistors
The KSZ8864RMN reduces board cost and simplifies board layout by using on-chip termination resistors for RX/TX
differential pairs without the external termination resistors. The solution of the on chip termination and internal biasing will
enhance much power consumption compare with using external biasing and termination resistors, and the transformer will
not consume power any longer. The center tap doesn’t need to be tied to analog power, just leave them floating or
connect the capacitors to ground separately.
Functional Overview: Power Management
The KSZ8864RMN can also use multiple power level of 3.3V, 2.5V or 1.8V for VDDIO to support different I/O voltage.
The KSZ8864RMN supports enhanced power management feature in low power state with energy detection to ensure
low-power dissipation during device idle periods. There are five operation modes under the power management function
which is controlled by the Register 14 bit [4:3] and the Port Register Control 13 bit3 as shown below:
Register 14 bit [4:3] = 00 Normal Operation Mode
Register 14 bit [4:3] = 01 Energy Detect Mode
Register 14 bit [4:3] = 10 Soft Power Down Mode
Register 14 bit [4:3] = 11 Power Saving Mode
The Port Register Control 13 bit 3 =1 is for the Port Based Power-Down Mode
Table 2 indicates all internal function blocks status under four different power management operation modes.
Power Management Operation Modes
KSZ8864RMN
Function Blocks
Normal Mode
Power Saving Mode
Energy Detect Mode
Soft Power Down Mode
Internal PLL Clock
Enabled
Disabled
Tx/Rx PHY
Enabled
Rx unused block disabled
Energy detect at Rx
Disabled
MAC
Enabled
Disabled
Host Interface
Enabled
Disabled
Table 2. Internal Function Block Status
Normal Operation Mode
This is the default setting bit [4:3] =00 in register 14 after the chip power-up or hardware reset. When KSZ8864RMN is in
this normal operation mode, all PLL clocks are running, PHY and MAC are on and the host interface is ready for CPU
read or write.
During the normal operation mode, the host CPU can set the bit [4:3] in register 14 to transit the current normal operation
mode to any one of the other three power management operation modes.
Energy Detect Mode
The energy detect mode provides a mechanism to save more power than in the normal operation mode when the
KSZ8864RMN is not connected to an active link partner. In this mode, if the cable is not plugged, then the KSZ8864RMN
can automatically enter to a low power state, i.e., the energy detect mode. In this mode, KSZ8864RMN will keep
transmitting 120ns width pulses at 1 pulse/s rate. Once activity resumes due to plugging a cable or attempting by the far
end to establish link, the KSZ8864RMN can automatically power up to normal power state in energy detect mode.
Energy detect mode consists of two states, normal power state and low power state. While in low power state, the
KSZ8864RMN reduces power consumption by disabling all circuitry except the energy detect circuitry of the receiver. The
energy detect mode is entered by setting bit [4:3] = 01 in register 14. When the KSZ8864RMN is in this mode, it will
monitor the cable energy. If there is no energy on the cable for a time longer than pre-configured value at bit [7:0] Go-
Sleep time in register 15, then the KSZ8864RMN will go into a low power state. When KSZ8864RMN is in low power
state, it will keep monitoring the cable energy. Once the energy is detected from the cable, KSZ8864RMN will enter
normal power state. When KSZ8864RMN is at normal power state, it is able to transmit or receive packet from the cable.
相关PDF资料 |
PDF描述 |
|---|---|
| KSZ8873FLLI | IC ETHERNET SWITCH 3PORT 64LQFP |
| KSZ8873MLLJ | IC ETHERNET SWITCH 3PORT 64LQFP |
| KSZ8873MMLI | IC ETHERNET SWITCH 3PORT 64LQFP |
| KSZ8893FQL | IC SWITCH FAST ETH 3PORT 128PQFP |
| KSZ8895MQI | IC ETHERNET SWITCH 5PORT 128PQFP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| KSZ8864RMNU | 功能描述:以太网 IC 4-Port 10/100BT Switch with MII/RMII (Automotive) RoHS:否 制造商:Micrel 产品:Ethernet Switches 收发器数量:2 数据速率:10 Mb/s, 100 Mb/s 电源电压-最大:1.25 V, 3.45 V 电源电压-最小:1.15 V, 3.15 V 最大工作温度:+ 85 C 封装 / 箱体:QFN-64 封装:Tray |
| KSZ8864RMNU TR | 制造商:Micrel Inc 功能描述:IC ETHERNET SWITCH 4PORT 64MLF |
| KSZ8873FLL | 功能描述:以太网 IC 3-Port Fast Ethernet Switch with 2x FX Ports - Lead free RoHS:否 制造商:Micrel 产品:Ethernet Switches 收发器数量:2 数据速率:10 Mb/s, 100 Mb/s 电源电压-最大:1.25 V, 3.45 V 电源电压-最小:1.15 V, 3.15 V 最大工作温度:+ 85 C 封装 / 箱体:QFN-64 封装:Tray |
| KSZ8873FLL-EVAL | 功能描述:以太网开发工具 3-Port Fast Ethernet Switch with 2x FX Ports - Evaluation Board RoHS:否 制造商:Micrel 产品:Evaluation Boards 类型:Ethernet Transceivers 工具用于评估:KSZ8873RLL 接口类型:RMII 工作电源电压: |
| KSZ8873FLLI | 功能描述:以太网 IC 3-Port Fast Ethernet Switch with 2x FX Ports (Industrial Grade) RoHS:否 制造商:Micrel 产品:Ethernet Switches 收发器数量:2 数据速率:10 Mb/s, 100 Mb/s 电源电压-最大:1.25 V, 3.45 V 电源电压-最小:1.15 V, 3.15 V 最大工作温度:+ 85 C 封装 / 箱体:QFN-64 封装:Tray |
发布紧急采购，3分钟左右您将得到回复。