参数资料
型号: KSZ9021RLI
厂商: Micrel Inc
文件页数: 6/58页
文件大小: 0K
描述: TXRX ETHERNET GB RGMII 64-LQFP
标准包装: 160
类型: 收发器
驱动器/接收器数: 8/8
规程: 千兆位以太网
电源电压: 3.135 V ~ 3.465 V
安装类型: 表面贴装
封装/外壳: 64-LQFP 裸露焊盘
供应商设备封装: 64-E-LQFP
包装: 托盘
其它名称: 576-3636
KSZ9021RLI-ND
MCP444X/446X
DS22265A-page 14
2010 Microchip Technology Inc.
FIGURE 1-3:
I2C Bus Data Timing.
90
91
92
100
101
103
106
107
109
110
102
SCL
SDA
In
SDA
Out
TABLE 1-3:
I2C BUS DATA REQUIREMENTS (SLAVE MODE)
I2C AC Characteristics
Standard Operating Conditions (unless otherwise specified)
Operating Temperature
–40
°C ≤ TA ≤ +125°C (Extended)
Operating Voltage VDD range is described in AC/DC characteristics
Param.
No.
Sym
Characteristic
Min
Max
Units
Conditions
100
THIGH
Clock high time
100 kHz mode
4000
ns
1.8V-5.5V
400 kHz mode
600
ns
2.7V-5.5V
1.7 MHz mode
120
ns
4.5V-5.5V
3.4 MHz mode
60
ns
4.5V-5.5V
101
TLOW
Clock low time
100 kHz mode
4700
ns
1.8V-5.5V
400 kHz mode
1300
ns
2.7V-5.5V
1.7 MHz mode
320
ns
4.5V-5.5V
3.4 MHz mode
160
ns
4.5V-5.5V
Note 1:
As a transmitter, the device must provide this internal minimum delay time to bridge the undefined region
(minimum 300 ns) of the falling edge of SCL to avoid unintended generation of START or STOP conditions.
2:
A fast-mode (400 kHz) I2C-bus device can be used in a standard-mode (100 kHz) I2C-bus system, but the
requirement tSU;DAT ≥ 250 ns must then be met. This will automatically be the case if the device does not
stretch the LOW period of the SCL signal. If such a device does stretch the LOW period of the SCL signal,
it must output the next data bit to the SDA line
TR max.+tSU;DAT = 1000 + 250 = 1250 ns (according to the standard-mode I2C bus specification) before
the SCL line is released.
3:
The MCP44X1/MCP44X2 device must provide a data hold time to bridge the undefined part between VIH
and VIL of the falling edge of the SCL signal. This specification is not a part of the I2C specification, but
must be tested in order to ensure that the output data will meet the setup and hold specifications for the
receiving device.
4:
Use Cb in pF for the calculations.
5:
Not Tested.
6:
A Master Transmitter must provide a delay to ensure that difference between SDA and SCL fall times do
not unintentionally create a Start or Stop condition.
7:
Ensured by the TAA 3.4 MHz specification test.
相关PDF资料
PDF描述
VI-J4T-MY-S CONVERTER MOD DC/DC 6.5V 50W
VI-2NR-MX CONVERTER MOD DC/DC 7.5V 75W
LTC1348CSW#PBF IC TXRX 3.3V/5V RS232 28-SOIC
VI-2NP-MX CONVERTER MOD DC/DC 13.8V 75W
VI-J4R-MY-S CONVERTER MOD DC/DC 7.5V 50W
相关代理商/技术参数
参数描述
KSZ9021RN 功能描述:以太网 IC Gigabit Ethernet Transceiver with RGMII, Lead Free RoHS:否 制造商:Micrel 产品:Ethernet Switches 收发器数量:2 数据速率:10 Mb/s, 100 Mb/s 电源电压-最大:1.25 V, 3.45 V 电源电压-最小:1.15 V, 3.15 V 最大工作温度:+ 85 C 封装 / 箱体:QFN-64 封装:Tray
KSZ9021RN-EVAL 功能描述:以太网开发工具 Gigabit Ethernet Transceiver with RGMII - Evaluation Board RoHS:否 制造商:Micrel 产品:Evaluation Boards 类型:Ethernet Transceivers 工具用于评估:KSZ8873RLL 接口类型:RMII 工作电源电压:
KSZ9021RNI 功能描述:以太网 IC Gigabit Ethernet Transceiver with RGMII, I-Temp RoHS:否 制造商:Micrel 产品:Ethernet Switches 收发器数量:2 数据速率:10 Mb/s, 100 Mb/s 电源电压-最大:1.25 V, 3.45 V 电源电压-最小:1.15 V, 3.15 V 最大工作温度:+ 85 C 封装 / 箱体:QFN-64 封装:Tray
KSZ9031MNX 制造商:MICREL 制造商全称:Micrel Semiconductor 功能描述:The KSZ9031MNX is a completely integrated triple-speed (10Base-T/100Base-TX/1000Base-T) Ethernet physicallayer transceiver for transmission and reception of data on standard CAT-5 unshielded twisted pair (UTP) cable.
KSZ9031MNXCA 功能描述:以太网 IC 1-Port Gigabit Ethernet PHY RoHS:否 制造商:Micrel 产品:Ethernet Switches 收发器数量:2 数据速率:10 Mb/s, 100 Mb/s 电源电压-最大:1.25 V, 3.45 V 电源电压-最小:1.15 V, 3.15 V 最大工作温度:+ 85 C 封装 / 箱体:QFN-64 封装:Tray