参数资料
型号: L5994A
厂商: STMICROELECTRONICS
元件分类: 稳压器
英文描述: 1 A DUAL SWITCHING CONTROLLER, 345 kHz SWITCHING FREQ-MAX, PQFP32
封装: TQFP-32
文件页数: 14/26页
文件大小: 322K
代理商: L5994A
Obsolete
Product(s)
- Obsolete
Product(s)
21/26
L5994 - L5994A
The electrical schematic, illustrated in fig. 7, shows that some pull-up/down resistor are added to the compo-
nents strictly needed in a real application. Along with a quad dip-switch, they allow to set manually the logic sig-
nals that control the chip operation. These signals are in the present case:
- Switch 1: RUN1 (0= 5.1V OFF, 1= 5.1V ON)
- Switch 2: OSC (0= 200kHz, 1=300kHz)
- Switch 3: NOSKIP (0= pulse-skipping ON, 1= pulse-skipping OFF)
- Switch 4: RUN2 (0= 3.3V OFF, 1= 3.3V ON)
Please note that as long as each regulator is disabled, the relevant low-side MOSFET is in ON state. Hence, if
the load is capable of sourcing current, it will be short-circuited to ground through the choke and the low-side
MOS.
Although the default switching frequency is 300kHz (switch 2 set on 1) and the passive components have been
selected for this frequency, the demo board will work satisfactorily at 200kHz as well. Actually, at 200kHz the
regulators exhibit the maximum efficiency and the maximum extension of the input voltage range downwards.
On the other hand, the output ripple is greater and the dynamic behaviour slightly worse.
The demonstration board, as it is, does not provide an interface for synchronization. Anyway, it is possible to
synchronize the oscillator (with an appropriate signal: 5V amplitude pulses, spaced out by 400ns min.), provided
the switch is set on 1, simply by feeding the signal into the middle of the divider R8-R9. In this way, synchroni-
zation can be achieved at a frequency higher than 300kHz. To synchronize the oscillator to a frequency between
200kHz and 300kHz, heavier interventions on the board are needed.
Pulse-skipping operation is enabled by default in order to maximize efficiency also in low load current range.
The transition between PWM and pulse-skipping occurs approximately below 1A, however there is a region in
which the two operation modes coexist rather than a definite boundary. That can be seen on the scope as an
irregularity of the waveforms but does not have much influence both on output ripple and efficiency.
Those who do not appreciate asynchronous operation of the pulse-skipping mode can disable it for both regu-
lators, by setting switch 3 on 1. That maintains PWM operation up to very low output currents where, however,
the regulation becomes incompatible with the switching frequency. This means that the minimum ON-time of
the high-side MOSFET is too long for the thruput energy level at the operating frequency. Thus the control sys-
tem begins skipping conduction cycles to avoid the output voltage drifting upwards.
相关PDF资料
PDF描述
L5994 1 A DUAL SWITCHING CONTROLLER, 345 kHz SWITCHING FREQ-MAX, PQFP32
L6206PD013TR STEPPER MOTOR CONTROLLER, 5.6 A, PDSO36
L6207PD013TR STEPPER MOTOR CONTROLLER, 5.6 A, PDSO36
L6219DSA STEPPER MOTOR CONTROLLER, 1 A, PDSO24
L6228PDTR STEPPER MOTOR CONTROLLER, 2.8 A, PDSO36
相关代理商/技术参数
参数描述
L5995 制造商:未知厂家 制造商全称:未知厂家 功能描述:Current-Mode SMPS Controller
L5996 制造商:STMICROELECTRONICS 制造商全称:STMicroelectronics 功能描述:5 BIT DYNAMIC DAC CONTROLLER FOR MOBILE CPU
L-59BL/1EGW 制造商:Kingbright Corporation 功能描述: 制造商:Kingbright Corporation 功能描述:LED 5MM RED/GREEN 40MCD/60MCD 制造商:Kingbright Corporation 功能描述:LED, 5MM, RED/GREEN, 40MCD/60MCD 制造商:Kingbright Corporation 功能描述:LED, 5MM, RED/GREEN, 40MCD/60MCD, LED Colour:Red, Green, Height:7.24mm, Width:7. 制造商:Kingbright Corporation 功能描述:Red/grn r/a cbi,5mm,L-59BL/1EGW
L-59BL/1EYW 制造商:Kingbright Corporation 功能描述: 制造商:Kingbright Corporation 功能描述:LED 5MM RED/YELLOW 40MCD/40MCD 制造商:Kingbright Corporation 功能描述:LED, 5MM, RED/YELLOW, 40MCD/40MCD 制造商:Kingbright Corporation 功能描述:LED, 5MM, RED/YELLOW, 40MCD/40MCD, LED Colour:Red, Yellow, Height:7.24mm, Width:
L-59BL/1GEW 制造商:Kingbright Corporation 功能描述: