参数资料
型号: L6563STR
厂商: STMICROELECTRONICS
元件分类: 稳压器
英文描述: POWER FACTOR CONTROLLER, PDSO14
封装: ROHS COMPLIANT, SOP-14
文件页数: 19/42页
文件大小: 1230K
代理商: L6563STR
Application information
L6563S
26/42
Doc ID 16116 Rev 3
where fL is the line frequency. The amount of 3rd harmonic distortion introduced by this
ripple, related to the amplitude of its 2fL component, will be:
shows a diagram that helps choose the time constant RFFCFF based on the
amount of maximum desired 3rd harmonic distortion. Always connect RFF and CFF to the
pin, the IC will not work properly if the pin is either left floating or connected directly to
ground.
Figure 37.
RFFCFF as a function of 3rd harmonic distortion introduced in the input
current
The dynamics of the voltage feedforward input, that is the output of the multiplier, is limited
downwards at 0.8 V (see Figure 36), so that cannot increase any more if the voltage on the
VFF pin is below 0.8 V. This helps to prevent excessive power flow when the line voltage is
lower than the minimum specified value.
6.4
THD optimizer circuit
The L6563S is provided with a special circuit that reduces the conduction dead-angle
occurring to the AC input current near the zero-crossings of the line voltage (crossover
distortion). In this way the THD (total harmonic distortion) of the current is considerably
reduced.
A major cause of this distortion is the inability of the system to transfer energy effectively
when the instantaneous line voltage is very low. This effect is magnified by the high-
frequency filter capacitor placed after the bridge rectifier, which retains some residual
voltage that causes the diodes of the bridge rectifier to be reverse-biased and the input
current flow to temporarily stop.
To overcome this issue the device forces the PFC pre-regulator to process more energy
near the line voltage zero-crossings as compared to that commanded by the control loop.
This will result in both minimizing the time interval where energy transfer is lacking and fully
discharging the high-frequency filter capacitor after the bridge.
shows the internal block diagram of the THD optimizer circuit.
FF
L
3
C
R
f
2
100
%
D
π
=
D %
3
0.1110
0.01
0.1
1
10
f = 50 Hz
L
f = 60 Hz
L
R C
[s]
FF
相关PDF资料
PDF描述
L6563S POWER FACTOR CONTROLLER, PDSO14
L6564DTR SWITCHING CONTROLLER, PDSO10
L6564D SWITCHING CONTROLLER, PDSO10
L6585DE POWER FACTOR CONTROLLER, PDSO20
L6585DETR POWER FACTOR CONTROLLER, PDSO20
相关代理商/技术参数
参数描述
L6563TR 功能描述:功率因数校正 IC POWER SUPPLY RoHS:否 制造商:Fairchild Semiconductor 开关频率:300 KHz 最大功率耗散: 最大工作温度:+ 125 C 安装风格:SMD/SMT 封装 / 箱体:SOIC-8 封装:Reel
L6564 制造商:STMICROELECTRONICS 制造商全称:STMicroelectronics 功能描述:10 pin transition-mode PFC controller
L6564D 功能描述:IC PFC CTRLR TRANSITION 10SSOP RoHS:是 类别:集成电路 (IC) >> PMIC - PFC(功率因数修正) 系列:- 产品培训模块:GreenChip Synchronous Rectification Control Family of ICs 标准包装:1 系列:- 模式:间歇导电(DCM) 频率 - 开关:- 电流 - 启动:- 电源电压:8.6 V ~ 38 V 工作温度:-20°C ~ 150°C 安装类型:表面贴装 封装/外壳:14-SOIC(0.154",3.90mm 宽) 供应商设备封装:14-SO 包装:Digi-Reel® 其它名称:568-5348-6
L6564DTR 功能描述:功率因数校正 IC Transition Mode PFC 5mA 90uA 1.5% Ref RoHS:否 制造商:Fairchild Semiconductor 开关频率:300 KHz 最大功率耗散: 最大工作温度:+ 125 C 安装风格:SMD/SMT 封装 / 箱体:SOIC-8 封装:Reel
L6564H 功能描述:功率因数校正 IC High Voltage Startup Trans-Mode PFC 700V RoHS:否 制造商:Fairchild Semiconductor 开关频率:300 KHz 最大功率耗散: 最大工作温度:+ 125 C 安装风格:SMD/SMT 封装 / 箱体:SOIC-8 封装:Reel