- 您现在的位置：买卖IC网 > PDF目录69003 > L6563STR (STMICROELECTRONICS) POWER FACTOR CONTROLLER, PDSO14 PDF资料下载
参数资料
| 型号： | L6563STR |
| 厂商： | STMICROELECTRONICS |
| 元件分类： | 稳压器 |
| 英文描述： | POWER FACTOR CONTROLLER, PDSO14 |
| 封装： | ROHS COMPLIANT, SOP-14 |
| 文件页数： | 42/42页 |
| 文件大小： | 1230K |
| 代理商： | L6563STR |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页当前第42页
L6563S
Pin connection
Doc ID 16116 Rev 3
9/42
7PFC_OK
PFC pre-regulator output voltage monitoring/disable function. This pin senses the output
voltage of the PFC pre-regulator through a resistor divider and is used for protection purposes.
If the voltage on the pin exceeds 2.5 V the IC stops switching and restarts as the voltage on the
pin falls below 2.4 V. However, if the voltage of the INV pin falls 40 mV below that one of the pin
PFC_OK, a feedback failure is assumed. In this case the device is latched off and the pin
PWM_LATCH (#8) is asserted high. Normal operation can be resumed only by cycling Vcc
bringing its value lower than 6V before to move up the Turn on threshold.
If the voltage on this pin is brought below 0.23 V the IC is shut down. To restart the IC the
voltage on the pin must go above 0.27 V. This can be used as a remote on/off control input.
8PWM_LATCH
Output pin for fault signaling. During normal operation this pin features high impedance. If a
feedback failure is detected (PFC_OK > 2.5 V and INV+40 mV < PFC_OK) the pin is asserted
high. Normally, this pin is used to stop the operation of the dc-dc converter supplied by the PFC
pre-regulator by invoking a latched disable of its PWM controller. If not used, the pin will be left
floating.
9PWM_STOP
Output pin for fault signaling. During normal operation this pin features high impedance. If the
IC is disabled by a voltage below 0.8 V on pin RUN (#10) the voltage on the pin is pulled to
ground. Normally, this pin is used to temporarily stop the operation of the dc-dc converter
supplied by the PFC pre-regulator by disabling its PWM controller. A typical usage of this
function is brownout protection in systems where the PFC pre-regulator is the master stage. If
not used, the pin will be left floating.
10
RUN
Remote ON/OFF control. A voltage below 0.8V shuts down (not latched) the IC and brings its
consumption to a considerably lower level. PWM_STOP is asserted low. The IC restarts as the
voltage at the pin goes above 0.88 V. Connect this pin to pin VFF (#5) either directly or through
a resistor divider to use this function as brownout (AC mains undervoltage) protection.
11
ZCD
Boost inductor’s demagnetization sensing input for transition-mode operation. A negative-going
edge triggers MOSFET’s turn-on.
12
GND
Ground. Current return for both the signal part of the IC and the gate driver.
13
GD
Gate driver output. The totem pole output stage is able to drive power MOSFET’s and IGBT’s
with a peak current of 600 mA source and 800 mA sink. The high-level voltage of this pin is
clamped at about 12 V to avoid excessive gate voltages.
14
Vcc
Supply voltage of both the signal part of the IC and the gate driver. Sometimes a small bypass
capacitor (0.1 F typ.) to GND might be useful to get a clean bias voltage for the signal part of
the IC.
Table 3.
Pin description (continued)
n°
Name
Function
相关PDF资料 |
PDF描述 |
|---|---|
| L6563S | POWER FACTOR CONTROLLER, PDSO14 |
| L6564DTR | SWITCHING CONTROLLER, PDSO10 |
| L6564D | SWITCHING CONTROLLER, PDSO10 |
| L6585DE | POWER FACTOR CONTROLLER, PDSO20 |
| L6585DETR | POWER FACTOR CONTROLLER, PDSO20 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| L6563TR | 功能描述:功率因数校正 IC POWER SUPPLY RoHS:否 制造商:Fairchild Semiconductor 开关频率:300 KHz 最大功率耗散: 最大工作温度:+ 125 C 安装风格:SMD/SMT 封装 / 箱体:SOIC-8 封装:Reel |
| L6564 | 制造商:STMICROELECTRONICS 制造商全称:STMicroelectronics 功能描述:10 pin transition-mode PFC controller |
| L6564D | 功能描述:IC PFC CTRLR TRANSITION 10SSOP RoHS:是 类别:集成电路 (IC) >> PMIC - PFC（功率因数修正） 系列:- 产品培训模块:GreenChip Synchronous Rectification Control Family of ICs 标准包装:1 系列:- 模式:间歇导电（DCM） 频率 - 开关:- 电流 - 启动:- 电源电压:8.6 V ~ 38 V 工作温度:-20°C ~ 150°C 安装类型:表面贴装 封装/外壳:14-SOIC（0.154"，3.90mm 宽） 供应商设备封装:14-SO 包装:Digi-Reel® 其它名称:568-5348-6 |
| L6564DTR | 功能描述:功率因数校正 IC Transition Mode PFC 5mA 90uA 1.5% Ref RoHS:否 制造商:Fairchild Semiconductor 开关频率:300 KHz 最大功率耗散: 最大工作温度:+ 125 C 安装风格:SMD/SMT 封装 / 箱体:SOIC-8 封装:Reel |
| L6564H | 功能描述:功率因数校正 IC High Voltage Startup Trans-Mode PFC 700V RoHS:否 制造商:Fairchild Semiconductor 开关频率:300 KHz 最大功率耗散: 最大工作温度:+ 125 C 安装风格:SMD/SMT 封装 / 箱体:SOIC-8 封装:Reel |
发布紧急采购，3分钟左右您将得到回复。