- 您现在的位置：买卖IC网 > PDF目录69003 > L6564D (STMICROELECTRONICS) SWITCHING CONTROLLER, PDSO10 PDF资料下载
参数资料
| 型号： | L6564D |
| 厂商： | STMICROELECTRONICS |
| 元件分类： | 稳压器 |
| 英文描述： | SWITCHING CONTROLLER, PDSO10 |
| 封装： | ROHS COMPLIANT, SSOP-10 |
| 文件页数： | 32/34页 |
| 文件大小： | 809K |
| 代理商： | L6564D |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页当前第32页第33页第34页
L6564
Pin connection
Doc ID 16202 Rev 1
7/34
3
Pin connection
Figure 2.
Pin connection
Table 3.
Pin description
n°
Name
Function
1INV
Inverting input of the error amplifier. The information on the output voltage of the PFC pre-
regulator is fed into the pin through a resistor divider.
The pin normally features high impedance.
2COMP
Output of the error amplifier. A compensation network is placed between this pin and INV (pin
1) to achieve stability of the voltage control loop and ensure high power factor and low THD.
To avoid uncontrolled rise of the output voltage at zero load, when the voltage on the pin falls
below 2.4 V the gate driver output will be inhibited (burst-mode operation).
3MULT
Main input to the multiplier. This pin is connected to the rectified mains voltage via a resistor
divider and provides the sinusoidal reference to the current loop. The voltage on this pin is used
also to derive the information on the RMS mains voltage.
4CS
Input to the PWM comparator. The current flowing in the MOSFET is sensed through a resistor,
the resulting voltage is applied to this pin and compared with an internal reference to determine
MOSFET’s turn-off.
A second comparison level at 1.7V detects abnormal currents (e.g. due to boost inductor
saturation) and, on this occurrence, activates a safety procedure that temporarily stops the
converter and limits the stress of the power components.
5VFF
Second input to the multiplier for 1/V2 function. A capacitor and a parallel resistor must be
connected from the pin to GND. They complete the internal peak-holding circuit that derives the
information on the RMS mains voltage. The voltage at this pin, a dc level equal to the peak
voltage on pin MULT (3), compensates the control loop gain dependence on the mains voltage.
Never connect the pin directly to GND but with a resistor ranging from 100K ohm (minimum) to
2M ohm (maximum). This pin is internally connected to a comparator in order to provide the
brownout (AC mains undervoltage) protection. A voltage below 0.8V shuts down (not latched)
the IC and brings its consumption to a considerably lower level. The IC restarts as the voltage
at the pin goes above 0.88V.
相关PDF资料 |
PDF描述 |
|---|---|
| L6585DE | POWER FACTOR CONTROLLER, PDSO20 |
| L6585DETR | POWER FACTOR CONTROLLER, PDSO20 |
| L6598 | SWITCHING CONTROLLER, 400 kHz SWITCHING FREQ-MAX, PDIP16 |
| L6598D013TR | SWITCHING CONTROLLER, 400 kHz SWITCHING FREQ-MAX, PDSO16 |
| L6710 | 2 A SWITCHING CONTROLLER, PQFP44 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| L6564DTR | 功能描述:功率因数校正 IC Transition Mode PFC 5mA 90uA 1.5% Ref RoHS:否 制造商:Fairchild Semiconductor 开关频率:300 KHz 最大功率耗散: 最大工作温度:+ 125 C 安装风格:SMD/SMT 封装 / 箱体:SOIC-8 封装:Reel |
| L6564H | 功能描述:功率因数校正 IC High Voltage Startup Trans-Mode PFC 700V RoHS:否 制造商:Fairchild Semiconductor 开关频率:300 KHz 最大功率耗散: 最大工作温度:+ 125 C 安装风格:SMD/SMT 封装 / 箱体:SOIC-8 封装:Reel |
| L6564HTR | 功能描述:功率因数校正 IC High Volt Start Up 700V PFC 100uA 6mA RoHS:否 制造商:Fairchild Semiconductor 开关频率:300 KHz 最大功率耗散: 最大工作温度:+ 125 C 安装风格:SMD/SMT 封装 / 箱体:SOIC-8 封装:Reel |
| L6564T | 制造商:STMICROELECTRONICS 制造商全称:STMicroelectronics 功能描述:10-pin transition-mode PFC controller |
| L6564TD | 功能描述:功率因数校正 IC 10-Pin Trans Mode PFC Bi 6mA 0.75W RoHS:否 制造商:Fairchild Semiconductor 开关频率:300 KHz 最大功率耗散: 最大工作温度:+ 125 C 安装风格:SMD/SMT 封装 / 箱体:SOIC-8 封装:Reel |
发布紧急采购，3分钟左右您将得到回复。