- 您现在的位置：买卖IC网 > PDF目录97995 > L6728D (STMICROELECTRONICS) 30 A SWITCHING CONTROLLER, 300 kHz SWITCHING FREQ-MAX, PDSO10 PDF资料下载
参数资料
| 型号： | L6728D |
| 厂商： | STMICROELECTRONICS |
| 元件分类： | 稳压器 |
| 英文描述： | 30 A SWITCHING CONTROLLER, 300 kHz SWITCHING FREQ-MAX, PDSO10 |
| 封装： | 3 X 3 MM, ROHS COMPLIANT, DFN-10 |
| 文件页数： | 13/33页 |
| 文件大小： | 1215K |
| 代理商： | L6728D |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页当前第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页
Application information
L6728D
20/33
Doc ID 16498 Rev 1
11
Application information
11.1
Inductor design
The inductance value is defined by a compromise between the dynamic response time, the
efficiency, the cost and the size. The inductor has to be calculated to maintain the ripple
current (
ΔI
L) between 20% and 30% of the maximum output current (typ). The inductance
value can be calculated with the following equation:
Where FSW is the switching frequency, VIN is the input voltage and VOUT is the output
voltage. Figure 9 shows the ripple current vs. the output voltage for different values of the
inductor, with VIN = 5 V and VIN = 12 V.
Increasing the value of the inductance reduces the current ripple but, at the same time,
increases the converter response time to a dynamic load change. The response time is the
time required by the inductor to change its current from initial to final value. Until the inductor
has finished its charging time, the output current is supplied by the output capacitors.
Minimizing the response time can minimize the output capacitance required. If the
compensation network is well-designed, during a load variation the device is able to set a
duty cycle value very different (0% or 80%) from a steady-state one. When this condition is
reached, the response time is limited by the time required to change the inductor current.
Figure 9.
Inductor current ripple vs output voltage
L
V
IN
V
OUT
–
F
SW
ΔI
L
------------------------------
V
OUT
V
IN
--------------
=
相关PDF资料 |
PDF描述 |
|---|---|
| L6911C | 1.3 A SWITCHING CONTROLLER, 1000 kHz SWITCHING FREQ-MAX, PDSO20 |
| L6911DTR | 1.3 A SWITCHING CONTROLLER, 1000 kHz SWITCHING FREQ-MAX, PDSO20 |
| L6911E | 1.3 A SWITCHING CONTROLLER, 1000 kHz SWITCHING FREQ-MAX, PDSO20 |
| L6911ETR | 1.3 A SWITCHING CONTROLLER, 1000 kHz SWITCHING FREQ-MAX, PDSO20 |
| L6924U013 | POWER SUPPLY SUPPORT CKT, PQCC16 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| L6728DTR | 功能描述:电流型 PWM 控制器 Single-Phase PWM 5V to 12V Controller RoHS:否 制造商:Texas Instruments 开关频率:27 KHz 上升时间: 下降时间: 工作电源电压:6 V to 15 V 工作电源电流:1.5 mA 输出端数量:1 最大工作温度:+ 105 C 安装风格:SMD/SMT 封装 / 箱体:TSSOP-14 |
| L6728H | 功能描述:电压模式 PWM 控制器 Sgl Output 300 KHz DFN-10 RoHS:否 制造商:Texas Instruments 输出端数量:1 拓扑结构:Buck 输出电压:34 V 输出电流: 开关频率: 工作电源电压:4.5 V to 5.5 V 电源电流:600 uA 最大工作温度:+ 125 C 最小工作温度:- 40 C 封装 / 箱体:WSON-8 封装:Reel |
| L6728HTR | 功能描述:电流型 PWM 控制器 SINGLE PHASE PWM CNTRL PWR GOOD RoHS:否 制造商:Texas Instruments 开关频率:27 KHz 上升时间: 下降时间: 工作电源电压:6 V to 15 V 工作电源电流:1.5 mA 输出端数量:1 最大工作温度:+ 105 C 安装风格:SMD/SMT 封装 / 箱体:TSSOP-14 |
| L6728TR | 功能描述:DC/DC 开关控制器 Sngl phase PWM controller RoHS:否 制造商:Texas Instruments 输入电压:6 V to 100 V 开关频率: 输出电压:1.215 V to 80 V 输出电流:3.5 A 输出端数量:1 最大工作温度:+ 125 C 安装风格: 封装 / 箱体:CPAK |
| L6730 | 功能描述:DC/DC 开关控制器 Adjustable Step Down Controller RoHS:否 制造商:Texas Instruments 输入电压:6 V to 100 V 开关频率: 输出电压:1.215 V to 80 V 输出电流:3.5 A 输出端数量:1 最大工作温度:+ 125 C 安装风格: 封装 / 箱体:CPAK |
发布紧急采购，3分钟左右您将得到回复。