- 您现在的位置：买卖IC网 > PDF目录39186 > L9935 (STMICROELECTRONICS) STEPPER MOTOR CONTROLLER, 2.5 A, PDSO20 PDF资料下载
参数资料
| 型号： | L9935 |
| 厂商： | STMICROELECTRONICS |
| 元件分类： | 运动控制电子 |
| 英文描述： | STEPPER MOTOR CONTROLLER, 2.5 A, PDSO20 |
| 封装： | LEAD FREE, POWER, MO-166, SOP-20 |
| 文件页数： | 10/29页 |
| 文件大小： | 275K |
| 代理商： | L9935 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页当前第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页
Functional description
L9935
5.10.1
Over temperature pre alarm
Typically 20K before thermal shut down takes place an over temperature pre alarm (bit7 and
bit6 low) takes place. Typically over temperature pre alarm temperature is between 150 °C
and 160 °C.
5.11
Application hints using a high resistive stepper motor
The L9935 was originally targeted on stepper chopping stepper motor application with
typical resistances of 8..12
Ω. Using motors with higher resistance will work too but
diagnosis behavior will slightly change. This paragraph shows the details that should be
taken in account using diagnosis for high resistive motors.
5.11.1
Startup behavior
The device has simple digital filter to avoid triggering diagnosis at a single event that could
be random noise. This digital filter needs 4 chopping pulses to settle. Using a high resistive
motor this chopping does not take place. Instead the digital filter samples each time a
polarity change takes place. So the first three response telegrams after reset may show an
’open load’ error.
H means check for HIGH at the error bits.
X means don’t care because filter is not yet settled.
Using 75 mA chopping immediately after stand by:
The high resistive motor can be forced to chopping operation in the low current range. This
leads to the same behavior as using a low resistive motor.
Short to VS detection using high resistive motors:
The short to VS flag is overwritten each time the chopper comparator responds. Having
detected a short this flag only can be reset by reaching chopping operation or resetting the
circuit (ENN=1). For a high resistive motor this leads to the following consequence: Once a
short to VS is detected the error flag will persist even if the short is removed again until
either a reset (ENN=1) or chopping (for example in 75mA mode) has taken place. We
suggest to return to operation once a short to VS was detected by using the low current
mode to reset the flag.
Table 7.
High and low resistive motor (error bits)
Input data
High resistive motor
(error bits)
Low resistive motor
(error bits)
Standby
1st telegram (550 mA or 900 mA)
HH
Reverse phase (550 mA or 900 mA)
XH
HH
Reverse phase (550 mA or 900 mA)
XH
HH
Any data
XH
HH
Any data
HH
相关PDF资料 |
PDF描述 |
|---|---|
| L9935013TR | STEPPER MOTOR CONTROLLER, 2.5 A, PDSO20 |
| LA1070 | SPECIALTY ANALOG CIRCUIT, PDSO28 |
| LA1070 | SPECIALTY ANALOG CIRCUIT, PDSO28 |
| LA1140 | FM, AUDIO DEMODULATOR, PZIP16 |
| LA1140 | FM, AUDIO DEMODULATOR, PZIP16 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| L9935013TR | 功能描述:马达/运动/点火控制器和驱动器 2-Ph Stepper Motor RoHS:否 制造商:STMicroelectronics 产品:Stepper Motor Controllers / Drivers 类型:2 Phase Stepper Motor Driver 工作电源电压:8 V to 45 V 电源电流:0.5 mA 工作温度:- 25 C to + 125 C 安装风格:SMD/SMT 封装 / 箱体:HTSSOP-28 封装:Tube |
| L9936 | 制造商:未知厂家 制造商全称:未知厂家 功能描述:DC Motor Controller/Driver |
| L9937 | 制造商:STMICROELECTRONICS 制造商全称:STMicroelectronics 功能描述:FULL BRIDGE MOTOR DRIVER |
| L993CG-1 | 制造商:Thomas & Betts 功能描述:1 INCH LR CONDUIT BODY W/CVR & GASK |
| L9942 | 制造商:STMicroelectronics 功能描述: |
发布紧急采购，3分钟左右您将得到回复。