- 您现在的位置：买卖IC网 > PDF目录39186 > L9935 (STMICROELECTRONICS) STEPPER MOTOR CONTROLLER, 2.5 A, PDSO20 PDF资料下载
参数资料
| 型号： | L9935 |
| 厂商： | STMICROELECTRONICS |
| 元件分类： | 运动控制电子 |
| 英文描述： | STEPPER MOTOR CONTROLLER, 2.5 A, PDSO20 |
| 封装： | LEAD FREE, POWER, MO-166, SOP-20 |
| 文件页数： | 9/29页 |
| 文件大小： | 275K |
| 代理商： | L9935 |
第1页第2页第3页第4页第5页第6页第7页第8页当前第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页
L9935
Functional description
5.6
Short from an output to ground
The current through the short will be detected by the protection of the source transistor. The
source transistor will turn off exceeding a current of typically 1.8 A. Minimum overload
detection current is 1.2 A. To obtain proper current regulation (by the sink transistors and not
by source transistor shut down) the maximum current of the PWM regulator should be set to
a maximum value of 1.1 A.
5.7
Diagnosis of a short to ground
Detecting an overload will set an overcurrent error (Error2 = LOW) (bit6). To reset the error
flag a new byte must be written into the interface. (Reset of the error flag takes place at the
rising slope of CSN).
5.8
Shorted load
With a shorted load both, the sink- and the source protection or the PWM alone will
respond. In either case there will be no flyback pulse.
5.9
Diagnosis of a shorted load
Shorting the load two events may take place:
–
overload (of the high side transistor) while low side transistor overcurrent is
detected will set the following combinations:
bit6 = LOW
bit7 = HIGH
–
overload is marginal. So the low side driver may turn off before overload is
detected. This leads to the combination bit6 = HIGH and bit7 = LOW.
5.10
Open load
An open load will not lead to any flyback pulses. Error detection will take advantage of the
flyback pulse. Missing the flyback pulse after reversing the polarity of a motor winding bit7
will become LOW.
Open load will not be tested in the low current mode (current bits HL) to avoid the risk of
instable diagnosis at low flyback currents. Open load immediately after reset or power down
may on random be detected in the low current mode too. This diagnosis however will not
persist longer than 8 changes of polarity.
We strongly suggest to test open load at a high current mode (combination LL).
While circuit clock speed passes the stepper motor resonant points during
acceleration/deceleration phase, it can happen that flyback energy is temporarily insufficient
for a proper open load detection. Under specific circumstances, pending on motor and load
characteristics, this could lead to sporadic faulty open load error messages despite proper
system operation. The recommended solution is an appropriate software filter approach.
相关PDF资料 |
PDF描述 |
|---|---|
| L9935013TR | STEPPER MOTOR CONTROLLER, 2.5 A, PDSO20 |
| LA1070 | SPECIALTY ANALOG CIRCUIT, PDSO28 |
| LA1070 | SPECIALTY ANALOG CIRCUIT, PDSO28 |
| LA1140 | FM, AUDIO DEMODULATOR, PZIP16 |
| LA1140 | FM, AUDIO DEMODULATOR, PZIP16 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| L9935013TR | 功能描述:马达/运动/点火控制器和驱动器 2-Ph Stepper Motor RoHS:否 制造商:STMicroelectronics 产品:Stepper Motor Controllers / Drivers 类型:2 Phase Stepper Motor Driver 工作电源电压:8 V to 45 V 电源电流:0.5 mA 工作温度:- 25 C to + 125 C 安装风格:SMD/SMT 封装 / 箱体:HTSSOP-28 封装:Tube |
| L9936 | 制造商:未知厂家 制造商全称:未知厂家 功能描述:DC Motor Controller/Driver |
| L9937 | 制造商:STMICROELECTRONICS 制造商全称:STMicroelectronics 功能描述:FULL BRIDGE MOTOR DRIVER |
| L993CG-1 | 制造商:Thomas & Betts 功能描述:1 INCH LR CONDUIT BODY W/CVR & GASK |
| L9942 | 制造商:STMicroelectronics 功能描述: |
发布紧急采购，3分钟左右您将得到回复。