- 您现在的位置：买卖IC网 > PDF目录39186 > L9935 (STMICROELECTRONICS) STEPPER MOTOR CONTROLLER, 2.5 A, PDSO20 PDF资料下载
参数资料
| 型号： | L9935 |
| 厂商： | STMICROELECTRONICS |
| 元件分类： | 运动控制电子 |
| 英文描述： | STEPPER MOTOR CONTROLLER, 2.5 A, PDSO20 |
| 封装： | LEAD FREE, POWER, MO-166, SOP-20 |
| 文件页数： | 7/29页 |
| 文件大小： | 275K |
| 代理商： | L9935 |
第1页第2页第3页第4页第5页第6页当前第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页
L9935
Functional description
Figure 7.
Pulse diagram to explain offset chopping.
Using offset chopping the changes of the supply current remain half as large as using non
offset chopping.
Turning off the oscillator for example by shorting pin OSC to ground will hinder turning on of
the bridges anymore after the comparators have generated a turn off signal.
External clocking is possible overdrives the charge and discharge currents of the oscillator
for example with a push pull logic gate. So several devices can be synchronized.
5.3
Protection and diagnosis functions
The L9935 provides several protection functions and error detection functions. Current
limitation usually is customer defined by the external current sense resistors. The current
sensed there is used to regulate the current through the stepper motor windings by pulse
width modulation. This PWM regulation protects the sink transistors. The source transistors
are protected by an internal overcurrent shut down turning off the source transistors in case
of overload.
Overload detection of the source transistor will turn off the bridge and set the corresponding
error flag.
To turn on the bridge again a new byte must be written into the interface. (Rising slope of
CSN resets the overload error flag).
Both bridges use the same flags. To locate which bridge is affected by an error the bridges
can be tested individually (One bridge just is turned off to check for the error in the other
bridge).
5.4
Short from an output to the supply voltage VS
The current will be limited by the pulse width modulator. The sink transistor will turn off again
after some microseconds. The transistor will periodically be turned on again by the oscillator
turn off delay
due to slope
velocity control
ΔI
VOSC
VSRB
total current consumption
current
threshold 1
current
threshold 2
VSRA
IVS
D99AT421
相关PDF资料 |
PDF描述 |
|---|---|
| L9935013TR | STEPPER MOTOR CONTROLLER, 2.5 A, PDSO20 |
| LA1070 | SPECIALTY ANALOG CIRCUIT, PDSO28 |
| LA1070 | SPECIALTY ANALOG CIRCUIT, PDSO28 |
| LA1140 | FM, AUDIO DEMODULATOR, PZIP16 |
| LA1140 | FM, AUDIO DEMODULATOR, PZIP16 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| L9935013TR | 功能描述:马达/运动/点火控制器和驱动器 2-Ph Stepper Motor RoHS:否 制造商:STMicroelectronics 产品:Stepper Motor Controllers / Drivers 类型:2 Phase Stepper Motor Driver 工作电源电压:8 V to 45 V 电源电流:0.5 mA 工作温度:- 25 C to + 125 C 安装风格:SMD/SMT 封装 / 箱体:HTSSOP-28 封装:Tube |
| L9936 | 制造商:未知厂家 制造商全称:未知厂家 功能描述:DC Motor Controller/Driver |
| L9937 | 制造商:STMICROELECTRONICS 制造商全称:STMicroelectronics 功能描述:FULL BRIDGE MOTOR DRIVER |
| L993CG-1 | 制造商:Thomas & Betts 功能描述:1 INCH LR CONDUIT BODY W/CVR & GASK |
| L9942 | 制造商:STMicroelectronics 功能描述: |
发布紧急采购，3分钟左右您将得到回复。