- 您现在的位置：买卖IC网 > PDF目录30715 > LA1862M FM, AUDIO DEMODULATOR, PDSO36 PDF资料下载
参数资料
| 型号： | LA1862M |
| 元件分类： | 接收器 |
| 英文描述： | FM, AUDIO DEMODULATOR, PDSO36 |
| 封装： | MFP-36 |
| 文件页数： | 6/27页 |
| 文件大小： | 810K |
| 代理商： | LA1862M |
第1页第2页第3页第4页第5页当前第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页
Detector
1.
This IC uses a peak differential detector.
2.
To adjust the detector coil, use the built-in automatic frequency circuit (AFC) and rotate the coil core until the voltage drop
between pins 29 and 33 is 0 V.
3.
Zeroing the AFC and minimizing the total harmonic distortion requires adjusting the capacitance between pin 30 and ground.
Note that stray circuit board capacitance can affect this capacitance value.
4.
The level of demodulation that is output depends on the inductance of the coil between pins 30 and 31, tuning capacity Q
and the capacitor size. Note that although raising Q increases the slope of the S-curve and thus the demodulation output, it
does so at the risk of increasing distortion.
5.
If the destination market is Europe, increasing the slope of the S-curve helps reduce interference from neighboring channels.
IF Count Buffer
1.
Pin 3 is the IF count buffer output. To activate the IF count circuit, apply a 5 V input to pin 3 through a 51 k
Ω resistor.
2.
The resistor connected to pin 2 determines the IF count buffer output sensitivity (seek stop sensitivity).
3.
Leave pins 2 and 3 open if the IF count buffer is not used.
4.
The largest time constant among those for the following pins determines the transient response characteristic of the IF count
buffer.
Pin 1: the S-meter output, pin 4: the start of muting, pin 5: the muting drive output and pin 29: the AFC output.
IF count system block diagram
The logical AND of the S-meter output and pin 3 control voltage generates the output 10.7 MHz IF count signal.
SD Output
1.
To obtain SD output, attach an external NPN transistor to pin 5 as shown in the following figure.
2.
The resistor connected between the base and ground is for
adjusting the SD sensitivity.
3.
The transient response characteristic of the resulting SD
circuit on pin 5 is, like that for the IF count buffer,
determined by the time constants for pins 1, 4, 5 and 29.
Raising the seek speed requires decreasing the time
constants. Decreasing them too far, however, reduces
muting transient response and risks introducing beat noise
and other distortion.
S-meter output
Band muting
Pin 3 control voltage
Comparator
Muting drive output
SD output
IF count buffer amplifier
IF count buffer output
SD output
LA1862M
No. 4092- 14/27
相关PDF资料 |
PDF描述 |
|---|---|
| LA1863M | 1-BAND, AUDIO TUNER, PQFP44 |
| LA1867NM | AM/FM, AUDIO DEMODULATOR, PQFP44 |
| LA1875M | AM/FM, AUDIO SINGLE CHIP RECEIVER, PDSO36 |
| LA1875M | AM/FM, AUDIO SINGLE CHIP RECEIVER, PDSO36 |
| LA1883M | AM/FM, AUDIO SINGLE CHIP RECEIVER, PQFP64 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LA1867NM | 制造商:SANYO 制造商全称:Sanyo Semicon Device 功能描述:Car Radio Single-Chip Tuner System |
| LA1867NM-MPB-E | 制造商:ON Semiconductor 功能描述: |
| LA186B-9SEF9UG-3-PF | 制造商:LIGITEK 制造商全称:LIGITEK electronics co., ltd. 功能描述:LED ARRAY |
| LA186B-9SEF-PF | 制造商:LIGITEK 制造商全称:LIGITEK electronics co., ltd. 功能描述:LED ARRAY |
| LA186B-DBK-2-PF | 制造商:LIGITEK 制造商全称:LIGITEK electronics co., ltd. 功能描述:LED ARRAY |
发布紧急采购，3分钟左右您将得到回复。