参数资料
| 型号： | LA4425PV-MPB-H |
| 厂商： | ON Semiconductor |
| 文件页数： | 4/8页 |
| 文件大小： | 0K |
| 描述： | IC AUDIO POWER AMP 5W 44SSOP |
| 标准包装： | 30 |
| 类型： | AB 类 |
| 输出类型： | 1-通道（单声道） |
| 在某负载时最大输出功率 x 通道数量： | 6W x 1 @ 4 欧姆 |
| 电源电压： | 5 V ~ 16 V |
| 特点： | 消除爆音，过压保护，短路保护，热保护 |
| 安装类型： | * |
| 供应商设备封装： | * |
| 封装/外壳： | * |
| 包装： | * |
4
INDUSTRIAL TEMPERATURERANGE
IDT72V73250 3.3V TIME SLOT INTERCHANGE
DIGITAL SWITCH 8,192 x 8,192
PIN DESCRIPTION
SYMBOL
NAME
I/O
DESCRIPTION
A0-14
Address 0 to 14
I
These address lines access all internal memories.
C32i
Clock
I
Serial clock for shifting data in/out on the serial data stream. This input accepts a 32.768 MHz clock.
CS
Chip Select
I
This active LOW input is used by a microprocessor to activate the microprocessor port of IDT72V73250.
D0-15
Data Bus 0-15
I/O
These pins are the data bits of the microprocessor port.
DS
Data Strobe
I
This active LOW input works in conjunction with
CS to enable the read and write operations and sets the
data bus lines (D0-D15).
DTA
Data Transfer
O
Indicates that a data bus transfer is complete. When the bus cycle ends, this pin drives HIGH and then goes
Acknowledgment
high-impedance, allowing for faster bus cycles with a weaker pull-up resistor. A pull-up resistor is required
to hold a HIGH level when the pin is in high-impedance.
FE
Frame Evaluation
I
This input can be used to measure delay in the data path by comparing the frame pulse, F32i, with this input.
F32i
Frame Pulse
I
This input accepts and automatically identifies frame synchronization signals formatted according to
ST-BUSand GCI specifications.
GND
Ground
Ground Rail
ODE
Output Drive Enable
I
This is the output enable control for the TX serial outputs. When the ODE input is LOW and the Output Stand
By bit of the Control Register is LOW, all TX outputs are in a high-impedance state. If this input is HIGH, the TX
output drivers are enabled. However, each channel may still be put into a high-impedance state by using the
per-channel control bits in the Connection Memory.
RESET
Device Reset
I
This input puts the IDT72V73250 into a reset state that clears the device internal counters, registers and
brings TX0-15 and D0-D15 into a high-impedance state. The
RESET pin must be held LOW for a minimum
of 20ns to properly reset the device.
R/
W
Read/Write
I
This input controls the direction of the data bus lines (D0-D15) during a microprocessor access.
RX0-15
DataStream
I
Serial data input stream. These streams have a data rate of 32.768 Mb/s.
Input 0 to 15
TCK
Test Clock
I
Provides the clock to the JTAG test logic.
TDI
Test Serial Data In
I
JTAG serial test instructions and data are shifted in on this pin. This pin is pulled HIGH by an internal pull-up
when not driven.
TDO
Test Serial Data Out
O
JTAG serial data is output on this pin on the falling edge of TCK. This pin is held in high-impedance state
when JTAG scan is not enabled.
TMS
Test Mode Select
I
JTAG signal that controls the state transitions of the TAP controller. This pin is pulled HIGH by an internal
pull-up when not driven.
TRST
TestReset
I
Asynchronously initializes the JTAG TAP controller by putting it in the Test-Logic-Reset state. This pin is
pulled by an internal pull-up when not driven. This pin should be pulsed LOW on power-up, or held LOW,
to ensure that the IDT72V73250 is in the normal functional mode.
TX0-7
TX Output 0 to 7
O
Serial data output stream. These streams have a data rate of 32.768 Mb/s.
(Three-StateOutputs)
TX8-15/
TX Output 8 to 15/
O
When all 16 output streams are selected via Control Register, these pins are the output streams TX8 to TX15
OEI0-7
Output Enable
and operate at 32.768Mb/s. When output enable function is selected, these pins reflect the active or high-
Indication0-7
impedance status for the corresponding output stream Output Enable Indication 0-7.
(Three-StateOutputs)
VCC
+3.3 Volt Power Supply.
相关PDF资料 |
PDF描述 |
|---|---|
| LA4625-E | IC BTL PWR AMP 13.5W 2CH SIP14HZ |
| LA4708N-E | IC BTL PWR AMP 20W 2CH SIP18H |
| LDS6000NQGI | IC SENSOR TCH PURETOUCH 28VFQFPN |
| LDS6003PYGI | IC SENSOR TCH PURETOUCH 28SSOP |
| LDS6005NQGI | IC SENSOR TCH PURETOUCH 28VFQFPN |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LA4425PV-TLM-H | 功能描述:功率放大器 AUDIO POWER AMP RoHS:否 制造商:TriQuint Semiconductor 封装 / 箱体: 工作电源电压:28 V 电源电流:2.5 A 工作温度范围: 封装: |
| LA4430 | 制造商:未知厂家 制造商全称:未知厂家 功能描述: |
| LA4440 | 制造商:SANYO 制造商全称:Sanyo Semicon Device 功能描述:6W 2-Channel, Bridge 19W typ Power Amplifier |
| LA4440-E | 功能描述:音频放大器 RoHS:否 制造商:STMicroelectronics 产品:General Purpose Audio Amplifiers 输出类型:Digital 输出功率: THD + 噪声: 工作电源电压:3.3 V 电源电流: 最大功率耗散: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:TQFP-64 封装:Reel |
| LA4440J-K-E | 功能描述:音频放大器 RoHS:否 制造商:STMicroelectronics 产品:General Purpose Audio Amplifiers 输出类型:Digital 输出功率: THD + 噪声: 工作电源电压:3.3 V 电源电流: 最大功率耗散: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:TQFP-64 封装:Reel |
发布紧急采购，3分钟左右您将得到回复。