- 您现在的位置：买卖IC网 > PDF目录19832 > LCMXO640E-4MN132I (Lattice Semiconductor Corporation)IC FPGA 640LUTS 132CSBGA PDF资料下载
参数资料
| 型号： | LCMXO640E-4MN132I |
| 厂商： | Lattice Semiconductor Corporation |
| 文件页数： | 19/88页 |
| 文件大小： | 0K |
| 描述： | IC FPGA 640LUTS 132CSBGA |
| 标准包装： | 360 |
| 系列： | MachXO |
| 可编程类型： | 系统内可编程 |
| 最大延迟时间 tpd(1)： | 4.2ns |
| 电压电源 - 内部： | 1.14 V ~ 1.26 V |
| 宏单元数： | 320 |
| 输入/输出数： | 101 |
| 工作温度： | -40°C ~ 100°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 132-LFBGA，CSPBGA |
| 供应商设备封装： | 132-CSPBGA（8x8） |
| 包装： | 托盘 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页当前第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页第73页第74页第75页第76页第77页第78页第79页第80页第81页第82页第83页第84页第85页第86页第87页第88页
Architecture
MachXO Family Data Sheet
of the devices also support differential input buffers. PCI clamps are available on the top Bank I/O buffers. The
PCI clamp is enabled after V CC , V CCAUX , and V CCIO are at valid operating levels and the device has been con-
figured. ?
?
The two pads in the pair are described as “true” and “comp”, where the true pad is associated with the positive
side of the differential input buffer and the comp (complementary) pad is associated with the negative side of
the differential input buffer.
2. Left and Right sysIO Buffer Pairs ?
The sysIO buffer pairs in the left and right Banks of the device consist of two single-ended output drivers and
two sets of single-ended input buffers (supporting ratioed and absolute input levels). The devices also have a
differential driver per output pair. The referenced input buffer can also be configured as a differential input buf-
fer. In these Banks the two pads in the pair are described as “true” and “comp”, where the true pad is associ-
ated with the positive side of the differential I/O, and the comp (complementary) pad is associated with the
negative side of the differential I/O.
Typical I/O Behavior During Power-up
The internal power-on-reset (POR) signal is deactivated when V CC and V CCAUX have reached satisfactory levels.
After the POR signal is deactivated, the FPGA core logic becomes active. It is the user’s responsibility to ensure
that all V CCIO Banks are active with valid input logic levels to properly control the output logic states of all the I/O
Banks that are critical to the application. The default configuration of the I/O pins in a blank device is tri-state with a
weak pull-up to VCCIO. The I/O pins will maintain the blank configuration until VCC, VCCAUX and VCCIO have
reached satisfactory levels at which time the I/Os will take on the user-configured settings.
The V CC and V CCAUX supply the power to the FPGA core fabric, whereas the V CCIO supplies power to the I/O buf-
fers. In order to simplify system design while providing consistent and predictable I/O behavior, the I/O buffers
should be powered up along with the FPGA core fabric. Therefore, V CCIO supplies should be powered up before or
together with the V CC and V CCAUX supplies
Supported Standards
The MachXO sysIO buffer supports both single-ended and differential standards. Single-ended standards can be
further subdivided into LVCMOS and LVTTL. The buffer supports the LVTTL, LVCMOS 1.2, 1.5, 1.8, 2.5, and 3.3V
standards. In the LVCMOS and LVTTL modes, the buffer has individually configurable options for drive strength,
bus maintenance (weak pull-up, weak pull-down, bus-keeper latch or none) and open drain. BLVDS and LVPECL
output emulation is supported on all devices. The MachXO1200 and MachXO2280 support on-chip LVDS output
buffers on approximately 50% of the I/Os on the left and right Banks. Differential receivers for LVDS, BLVDS and
LVPECL are supported on all Banks of MachXO1200 and MachXO2280 devices. PCI support is provided in the top
Banks of the MachXO1200 and MachXO2280 devices. Table 2-8 summarizes the I/O characteristics of the devices
in the MachXO family.
Tables 2-9 and 2-10 show the I/O standards (together with their supply and reference voltages) supported by the
MachXO devices. For further information on utilizing the sysIO buffer to support a variety of standards please see
the details of additional technical documentation at the end of this data sheet.
2-16
相关PDF资料 |
PDF描述 |
|---|---|
| GCM18DCMD | CONN EDGECARD 36POS .156 WW |
| 10018784-11002TLF | CONN PCI EXPRESS 98POS VERT PCB |
| 10018783-10001TLF | CONN PCI EXPRESS 64POS VERT PCB |
| XC2C128-6VQG100C | IC CR-II CPLD 128MCELL 100-VQFP |
| RSA36DRMN-S288 | CONN EDGECARD 72POS .125 EXTEND |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LCMXO640E-4T100C | 功能描述:CPLD - 复杂可编程逻辑器件 640 LUTs 74 IO 1.2V -4 Spd RoHS:否 制造商:Lattice 系列: 存储类型:EEPROM 大电池数量:128 最大工作频率:333 MHz 延迟时间:2.7 ns 可编程输入/输出端数量:64 工作电源电压:3.3 V 最大工作温度:+ 90 C 最小工作温度:0 C 封装 / 箱体:TQFP-100 |
| LCMXO640E-4T100I | 功能描述:CPLD - 复杂可编程逻辑器件 640 LUTs 74 IO 1.2V -4 Spd I RoHS:否 制造商:Lattice 系列: 存储类型:EEPROM 大电池数量:128 最大工作频率:333 MHz 延迟时间:2.7 ns 可编程输入/输出端数量:64 工作电源电压:3.3 V 最大工作温度:+ 90 C 最小工作温度:0 C 封装 / 箱体:TQFP-100 |
| LCMXO640E-4T144C | 功能描述:CPLD - 复杂可编程逻辑器件 640 LUTs 113 IO 1.2V -4 Spd RoHS:否 制造商:Lattice 系列: 存储类型:EEPROM 大电池数量:128 最大工作频率:333 MHz 延迟时间:2.7 ns 可编程输入/输出端数量:64 工作电源电压:3.3 V 最大工作温度:+ 90 C 最小工作温度:0 C 封装 / 箱体:TQFP-100 |
| LCMXO640E-4T144I | 功能描述:CPLD - 复杂可编程逻辑器件 640 LUTs 113 IO 1.2V -4 Spd I RoHS:否 制造商:Lattice 系列: 存储类型:EEPROM 大电池数量:128 最大工作频率:333 MHz 延迟时间:2.7 ns 可编程输入/输出端数量:64 工作电源电压:3.3 V 最大工作温度:+ 90 C 最小工作温度:0 C 封装 / 箱体:TQFP-100 |
| LCMXO640E-4TN100C | 功能描述:CPLD - 复杂可编程逻辑器件 640 LUTs 74 IO 1.2V -4 Spd RoHS:否 制造商:Lattice 系列: 存储类型:EEPROM 大电池数量:128 最大工作频率:333 MHz 延迟时间:2.7 ns 可编程输入/输出端数量:64 工作电源电压:3.3 V 最大工作温度:+ 90 C 最小工作温度:0 C 封装 / 箱体:TQFP-100 |
发布紧急采购，3分钟左右您将得到回复。