- 您现在的位置：买卖IC网 > PDF目录79951 > LIS302DLH (STMICROELECTRONICS) SPECIALTY ANALOG CIRCUIT, PBGA14 PDF资料下载
参数资料
| 型号： | LIS302DLH |
| 厂商： | STMICROELECTRONICS |
| 元件分类： | 模拟信号调理 |
| 英文描述： | SPECIALTY ANALOG CIRCUIT, PBGA14 |
| 封装： | 3 X 5 MM, 0.80 MM HEIGHT, ROHS COMPLIANT, PLASTIC, LGA-14 |
| 文件页数： | 8/37页 |
| 文件大小： | 673K |
| 代理商： | LIS302DLH |
第1页第2页第3页第4页第5页第6页第7页当前第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页
Application hints
LIS302DLH
16/37
Doc ID 15797 Rev 1
4
Application hints
Figure 5.
LIS302DLH electrical connection
The device core is supplied through Vdd line while the I/O pads are supplied through
Vdd_IO line. Power supply decoupling capacitors (100 nF ceramic, 10 F Aluminum) should
be placed as near as possible to the pin 6 of the device (common design practice).
All the voltage and ground supplies must be present at the same time to have proper
behavior of the IC (refer to
Figure 5). It is possible to remove Vdd maintaining Vdd_IO
without blocking the communication bus, in this condition the measurement chain is
powered off.
The functionality of the device and the measured acceleration data is selectable and
accessible through the I2C/SPI interface.When using the I2C, CS must be tied high.
The functions, the threshold and the timing of the two interrupt pins (INT 1 and INT 2) can be
completely programmed by the user through the I2C/SPI interface.
4.1
Soldering information
The LGA package is compliant with the ECOPACK, RoHS and “Green” standard.
It is qualified for soldering heat resistance according to JEDEC J-STD-020C.
Leave “Pin 1 Indicator” unconnected during soldering.
Land pattern and soldering recommendations are available at www.st.com.
6
8
13
1
Top VIEW
CS
10uF
Vdd
100nF
GND
Vdd_IO
SDO
SDA/SDI/SDO
IN
T
1
IN
T
2
SCL/SPC
Digital signal from/to signal controller.Signal’s levels are defined by proper selection of Vdd_IO
1
13
8
6
TOP VIEW
X
Z
Y
DIRECTIONS OF THE
DETECTABLE
ACCELERATIONS
相关PDF资料 |
PDF描述 |
|---|---|
| LM21215MH | 23.5 A SWITCHING REGULATOR, 525 kHz SWITCHING FREQ-MAX, PDSO20 |
| LM4041DIMX-ADJ | 1-OUTPUT TWO TERM VOLTAGE REFERENCE, 1.233 V, PDSO8 |
| LS4601-7ERDDTB1 | 1-OUTPUT 100 W AC-DC PWR FACTOR CORR MODULE |
| LK1501-7EPD3TB1 | 1-OUTPUT 150 W AC-DC REG PWR SUPPLY MODULE |
| LTC1043CD | SPECIALTY ANALOG CIRCUIT, CDIP18 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LIS302DLHTR | 功能描述:加速计 - 板上安装 MEMS digital output L-Power Motion Snsr RoHS:否 制造商:Murata 传感轴:Double 加速:12 g 灵敏度: 封装 / 箱体: 输出类型:Analog 数字输出 - 位数:11 bit 电源电压-最大:5.25 V 电源电压-最小:4.75 V 电源电流:4 mA 最大工作温度:+ 125 C 最小工作温度:- 40 C |
| LIS302DLTR | 功能描述:加速计 - 板上安装 MEMS Motion Sensor RoHS:否 制造商:Murata 传感轴:Double 加速:12 g 灵敏度: 封装 / 箱体: 输出类型:Analog 数字输出 - 位数:11 bit 电源电压-最大:5.25 V 电源电压-最小:4.75 V 电源电流:4 mA 最大工作温度:+ 125 C 最小工作温度:- 40 C |
| LIS302DLTR8 | 制造商:STMicroelectronics 功能描述:LIS302DLTR8 - Tape and Reel |
| LIS302DLTR-CUT TAPE | 制造商:ST 功能描述:LIS302DL Series 3 Axis ?/? g 3.3 V Digital Output Piccolo Accerometer - LGA-14 |
| LIS302SG | 功能描述:加速计 - 板上安装 MEMS MOTION SENSOR 3 AXIS +/-2g Piccolo RoHS:否 制造商:Murata 传感轴:Double 加速:12 g 灵敏度: 封装 / 箱体: 输出类型:Analog 数字输出 - 位数:11 bit 电源电压-最大:5.25 V 电源电压-最小:4.75 V 电源电流:4 mA 最大工作温度:+ 125 C 最小工作温度:- 40 C |
发布紧急采购，3分钟左右您将得到回复。