- 您现在的位置：买卖IC网 > PDF目录43919 > LIS33DE (STMICROELECTRONICS) SPECIALTY ANALOG CIRCUIT, PBGA16 PDF资料下载
参数资料
| 型号： | LIS33DE |
| 厂商： | STMICROELECTRONICS |
| 元件分类： | 模拟信号调理 |
| 英文描述： | SPECIALTY ANALOG CIRCUIT, PBGA16 |
| 封装： | 3 X 3 MM, 1 MM HEIGHT, GREEN, PLASTIC, LGA-16 |
| 文件页数： | 16/31页 |
| 文件大小： | 532K |
| 代理商： | LIS33DE |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页当前第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页
LIS33DE
Register description
Doc ID 15596 Rev 1
23/31
7
Register description
The device contains a set of registers which are used to control its behavior and to retrieve
acceleration data. The registers address, made of 7 bits, is used to identify them and to
write the data through serial interface.
7.1
CTRL_REG1 (20h)
Table 16.
CTRL_REG1 (20h) register
Table 17.
CTRL_REG1 (20h) register description
DR bit allows to select the data rate at which acceleration samples are produced. The
default value is ‘0’ which corresponds to a data-rate of 100 Hz. By changing the content of
DR to ‘1’ the selected data-rate will be set equal to 400 Hz.
PD bit allows to turn the device out of power-down mode. The device is in power-down
mode when PD= ‘0’ (default value after boot). The device is in normal mode when PD is set
to ‘1’.
STP, STM bits are used to activate the self-test function. When the bit is set to one, an
output change will occur to the device outputs (refer to Table 2 and 3 for specification) thus
allowing to check the functionality of the whole measurement chain.
Zen bit enables the generation of Data Ready signal for Z-axis measurement channel when
set to ‘1’. The default value is ‘1’.
Yen bit enables the generation of Data Ready signal for Y-axis measurement channel when
set to ’1’. The default value is ’1’.
Xen bit enables the generation of Data Ready signal for X-axis measurement channel when
set to ’1’. The default value is ’1’.
DR
PD
FS
STP
STM
Zen
Yen
Xen
DR
Data rate selection. Default value: 0
(0: 100 Hz output data rate; 1: 400 Hz output data rate)
PD
Power down control. Default value: 0
(0: power down mode; 1: active mode)
FS
Full scale selection. Default value: 0
(refer to table 2 for typical full scale value)
STP, STM
Self test enable. Default value: 0
(0: normal mode; 1: self test P, M enabled)
Zen
Z axis enable. Default value: 1
(0: Z axis disabled; 1: Z axis enabled)
Yen
Y axis enable. Default value: 1
(0: Y axis disabled; 1: Y axis enabled)
Xen
X axis enable. Default value: 1
(0: X axis disabled; 1: X axis enabled)
相关PDF资料 |
PDF描述 |
|---|---|
| LIS352AXTR | SPECIALTY ANALOG CIRCUIT, PBCC14 |
| LIS3DHTR | SPECIALTY ANALOG CIRCUIT, PBGA16 |
| LIS3DH | SPECIALTY ANALOG CIRCUIT, PBGA16 |
| LIS3L02AL | SPECIALTY ANALOG CIRCUIT, PBGA8 |
| LIS3L02ALTR | SPECIALTY ANALOG CIRCUIT, PBGA8 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LIS33DETR | 功能描述:加速计 - 板上安装 DGTL OUTPT MTN SEN MEMS ULTRA LO PWR RoHS:否 制造商:Murata 传感轴:Double 加速:12 g 灵敏度: 封装 / 箱体: 输出类型:Analog 数字输出 - 位数:11 bit 电源电压-最大:5.25 V 电源电压-最小:4.75 V 电源电流:4 mA 最大工作温度:+ 125 C 最小工作温度:- 40 C |
| LIS344AL | 功能描述:加速计 - 板上安装 MEMS Sensor RoHS:否 制造商:Murata 传感轴:Double 加速:12 g 灵敏度: 封装 / 箱体: 输出类型:Analog 数字输出 - 位数:11 bit 电源电压-最大:5.25 V 电源电压-最小:4.75 V 电源电流:4 mA 最大工作温度:+ 125 C 最小工作温度:- 40 C |
| LIS344ALH | 功能描述:加速计 - 板上安装 MEMS Inertial High Pef 3-Axis RoHS:否 制造商:Murata 传感轴:Double 加速:12 g 灵敏度: 封装 / 箱体: 输出类型:Analog 数字输出 - 位数:11 bit 电源电压-最大:5.25 V 电源电压-最小:4.75 V 电源电流:4 mA 最大工作温度:+ 125 C 最小工作温度:- 40 C |
| LIS344ALH_0804 | 制造商:STMICROELECTRONICS 制造商全称:STMicroelectronics 功能描述:MEMS inertial sensor high performance 3-axis 【2/【6g ultracompact linear accelerometer |
| LIS344ALHTR | 功能描述:加速计 - 板上安装 MEMS Inertial High Pef 3-Axis RoHS:否 制造商:Murata 传感轴:Double 加速:12 g 灵敏度: 封装 / 箱体: 输出类型:Analog 数字输出 - 位数:11 bit 电源电压-最大:5.25 V 电源电压-最小:4.75 V 电源电流:4 mA 最大工作温度:+ 125 C 最小工作温度:- 40 C |
发布紧急采购，3分钟左右您将得到回复。