- 您现在的位置：买卖IC网 > PDF目录67755 > LM12434CIWMX (NATIONAL SEMICONDUCTOR CORP) SPECIALTY ANALOG CIRCUIT, PDSO28 PDF资料下载
参数资料
| 型号： | LM12434CIWMX |
| 厂商： | NATIONAL SEMICONDUCTOR CORP |
| 元件分类： | 模拟信号调理 |
| 英文描述： | SPECIALTY ANALOG CIRCUIT, PDSO28 |
| 封装： | SOP-28 |
| 文件页数： | 20/80页 |
| 文件大小： | 1552K |
| 代理商： | LM12434CIWMX |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页当前第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页第73页第74页第75页第76页第77页第78页第79页第80页
60 Operational Information (Continued)
Acquisition Time
The LM12434 and LM12 L 438’s internal SH is designed
to operate at its minimum acquisition time (1125 15 ms
for a 12-bit a sign conversion) when the source imped-
ance RS is less than or equal to 60 80 X (fCLK s 8 6
MHz) When 60 80 X k RS s 417 556 kX the inter-
nal SH’s acquisition time can be increased to a maximum
of 488
65
m
s (12 a sign bits fCLK e 8 6 MHz) to
provide sufficient time for the sampling capacitor to charge
See Section 621 (Instruction RAM ‘‘00’’) Bits 12 – 15 for
more information
Instruction Register
The INSTRUCTION RAM is divided into 8 separate words
each with 48 (3 x 16) bit length Each word is separated into
three 16-bit sections Each word has a unique address and
different sections of the instruction word are selected by the
2-bit RAM pointer (RP) in the configuration register As
shown in
Figure 7 the Instruction RAM sections are labeled
Instructions Limits
1 and Limits
2 The Instruction sec-
tion holds operational (12-bit a sign 8-bit a sign or watch-
dog) information such as the input channels to be selected
the mode of operation to be performed for each instruction
and the duration of the acquisition period The other two
sections are used in the watchdog mode and the user-
defined limits are stored in them Each watchdog instruction
has 2 limits associated with it (usually a low limit and a high
limit but two low limits or two high limits may be pro-
grammed instead) The DAS starts executing from instruc-
tion 0 and moves through the next instructions up to any
user-specified instruction and then ‘‘loop back’’ to instruc-
tion 0 It is not necessary to execute all 8 instructions in the
instruction loop The cycle may be repeatedly executed until
stopped by the user The processor should access the In-
struction RAM only when the instruction sequencer is
stopped
FIFO Register
The FIFO Register stores the conversion results This regis-
ter is ‘‘Read only’’ and all the locations are accessed
through a single address Each time a conversion is per-
formed the result is stored in the FIFO and the FIFO’s inter-
nal write pointer points to the next location The pointer rolls
back to location 1 after a Write to location 32 The same
flow occurs when reading from the FIFO The internal FIFO
Writes and the external FIFO Reads do not affect each oth-
er’s pointer locations
Microprocessor overhead is reduced through the use of the
internal conversion FIFO Thirty-two consecutive conver-
sions can be completed and stored in the FIFO without any
microprocessor intervention The microprocessor can at
any time interrogate the FIFO and retrieve its contents It
can also wait for the LM12434 and LM12 L 438 to issue an
interrupt when the FIFO is full or after any number (s 32) of
conversions have been stored
Configuration Register
The CONFIGURATION Register is the main ‘‘control panel’’
of the DAS Writing 1s and 0s to the different bits of the
Configuration Register commands the DAS start or stop the
sequencer reset the pointers and flags go into ‘‘standby’’
mode for low power consumption calibrate offset and lin-
earity and select sections of the RAM
Other Registers
The INTERRUPT ENABLE Register lets the user activate up
to 7 sources for interrupt generation (refer to Section 623)
It also holds two user-programmable values One is the
number of conversions to be stored in the FIFO register
before the generation of the Data Ready interrupt The other
value is the instruction number that generates an interrupt
when the sequencer reaches that instruction
The INTERRUPT STATUS and LIMIT STATUS Registers
are ‘‘Read only’’ registers They are used as vectors to indi-
cate which conditions have generated the interrupt and
what watchdog limit boundaries have been passed Note
that the bits are set in the status registers upon occurrence
of their corresponding interrupt conditions regardless of
whether the condition is enabled for external interrupt gen-
eration
The TIMER Register can be programmed to insert a delay
before execution of each instruction A bit in the instruction
register enables or disables the insertion of the delay before
the execution of an instruction
Serial IO
A very flexible serial synchronous interface is provided to
facilitate reading from and writing to the LM12434 and
LM12 L 438’s registers The communication between the
LM12434 and LM12 L 438 and microcontrollers micro-
processors and other circuitry is accomplished through this
serial interface The serial interface is designed to directly
communicate with the synchronous serial interfaces of the
most popular microprocessors with no extra hardware re-
quirement The interface has been also designed to simplify
software development
27
相关PDF资料 |
PDF描述 |
|---|---|
| LM12L438CIWMX | SPECIALTY ANALOG CIRCUIT, PDSO28 |
| LM20323AMHX | 6 A SWITCHING REGULATOR, 570 kHz SWITCHING FREQ-MAX, PDSO20 |
| LM20323AMHE | 6 A SWITCHING REGULATOR, 570 kHz SWITCHING FREQ-MAX, PDSO20 |
| LM20323AMH | 6 A SWITCHING REGULATOR, 570 kHz SWITCHING FREQ-MAX, PDSO20 |
| LM22677QTJ-5.0 | 8.75 A SWITCHING REGULATOR, 600 kHz SWITCHING FREQ-MAX, PSSO7 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LM12438CIV | 制造商:NSC 制造商全称:National Semiconductor 功能描述:Sign Data Acquisition System with Serial I/O and Self-Calibration |
| LM12438CIWM | 制造商:NSC 制造商全称:National Semiconductor 功能描述:Sign Data Acquisition System with Serial I/O and Self-Calibration |
| LM12454 | 制造商:未知厂家 制造商全称:未知厂家 功能描述:General Purpose Controller Z84C15 |
| LM12454_06 | 制造商:NSC 制造商全称:National Semiconductor 功能描述:12-Bit + Sign Data Acquisition System with Self-Calibration |
| LM12454A WAF | 制造商:Texas Instruments 功能描述: |
发布紧急采购，3分钟左右您将得到回复。