- 您现在的位置：买卖IC网 > PDF目录67755 > LM12L438CIWMX (NATIONAL SEMICONDUCTOR CORP) SPECIALTY ANALOG CIRCUIT, PDSO28 PDF资料下载
参数资料
| 型号： | LM12L438CIWMX |
| 厂商： | NATIONAL SEMICONDUCTOR CORP |
| 元件分类： | 模拟信号调理 |
| 英文描述： | SPECIALTY ANALOG CIRCUIT, PDSO28 |
| 封装： | SOP-28 |
| 文件页数： | 51/80页 |
| 文件大小： | 1552K |
| 代理商： | LM12L438CIWMX |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页当前第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页第73页第74页第75页第76页第77页第78页第79页第80页
70 Digital Interface (Continued)
72 8051 INTERFACE MODE
The 8051 interface mode is designed to work directly with
the 8051 family of microcontrollers’ mode 0 serial interface
This interface mode is a simple shift register type of serial
data transfer The serial clock synchronizes the transfer of
data to and from the LM12434 and LM12 L 438 The inter-
face uses 3 lines a bidirectional data line (RXD) a serial
clock line (TXD) and a chip-select (CS) line More than one
device can share the data and serial clock lines provided
that each device has its own chip-select line
The 8051 mode is selected when the MODESEL1 and
MODESEL2 pins have the logic state of ‘‘00’’
Figure 14
shows a typical connection diagram for the 8051 mode seri-
al interface The CS RXD and TXD lines are respectively
assigned to interface pins P3 through P5 The P1 and P2
pins are not used in this mode and should be left open or
connected to logic ‘‘1’’ In this interface the idle state of the
serial clock TXD is logic ‘‘1’’ The data is stable at both
edges of the TXD clock and is shifted after its rising edge
The interface has a bidirectional RXD data line
The
LM12434 and LM12 L 438 leaves the RXD line in a high
impedance state whenever it is not outputting any data
Data transfer in this mode is byte oriented As mentioned
the LM12434 and LM12 L 438 has three different commu-
nication cycles write cycle read cycle and burst read cycle
At the start of each data transfer cycle ‘‘command byte’’ is
written to the LM12434 and LM12 L 438 followed by write
or read data The command byte informs the LM12434 and
LM12 L 438 about the communication cycle and carries
the following information
what type of data transfer (communication cycle) is start-
ed
which device register is to be accessed
The command byte has the following format
TLH11879 – 53
The first bit is the LSB of the byte based on the 8051 mode
0 serial interface protocol
Figure 13 shows the timing diagrams for different communi-
cation cycles
Figure 13a shows a write cycle Figure 13b
shows a read cycle
Figure 13c shows a burst read cycle
Note that these timing diagrams depict general relationships
between the SCLK edges the data bits and CS These dia-
grams are not meant to show guaranteed timing perform-
ance (See specification tables for parametric switching
characteristics)
Write cycle
A write cycle begins with the falling edge of the
CS Then a command byte is written to the DAS on the RXD
line synchronized by TXD clock The command byte has the
RW and B bits equal to zero Following the command byte
16 bits of data (2 bytes) is shifted in on the RXD line The
data is written to the register addressed in the command
byte (A3 A2 A1 A0) The data is always LSB first in this
interface CS will go high after the transfer of the last bit
thus completing the write cycle
Read cycle
A read cycle starts the same way as a write
cycle except that the command bytes RW bit is equal to
one Following the command byte the DAS outputs the
data on the RXD line synchronized with the microcontrol-
ler’s TXD clock The data is read from the register ad-
dressed in the command byte Data is shifted in LSB first
Again CS will go high after the transfer of the last data bit
thus completing the read cycle
55
相关PDF资料 |
PDF描述 |
|---|---|
| LM20323AMHX | 6 A SWITCHING REGULATOR, 570 kHz SWITCHING FREQ-MAX, PDSO20 |
| LM20323AMHE | 6 A SWITCHING REGULATOR, 570 kHz SWITCHING FREQ-MAX, PDSO20 |
| LM20323AMH | 6 A SWITCHING REGULATOR, 570 kHz SWITCHING FREQ-MAX, PDSO20 |
| LM22677QTJ-5.0 | 8.75 A SWITCHING REGULATOR, 600 kHz SWITCHING FREQ-MAX, PSSO7 |
| LM22677QTJE-5.0 | 8.75 A SWITCHING REGULATOR, 600 kHz SWITCHING FREQ-MAX, PSSO7 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LM12L454CIV | 制造商:Rochester Electronics LLC 功能描述:- Bulk 制造商:Texas Instruments 功能描述: |
| LM12L458 | 制造商:NSC 制造商全称:National Semiconductor 功能描述:12-Bit + Sign Data Acquisition System with Self-Calibration |
| LM12L458_06 | 制造商:NSC 制造商全称:National Semiconductor 功能描述:12-Bit + Sign Data Acquisition System with Self-Calibration |
| LM12L458CIV | 功能描述:模数转换器 - ADC RoHS:否 制造商:Texas Instruments 通道数量:2 结构:Sigma-Delta 转换速率:125 SPs to 8 KSPs 分辨率:24 bit 输入类型:Differential 信噪比:107 dB 接口类型:SPI 工作电源电压:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-32 |
| LM12L458CIV/NOPB | 功能描述:模数转换器 - ADC RoHS:否 制造商:Texas Instruments 通道数量:2 结构:Sigma-Delta 转换速率:125 SPs to 8 KSPs 分辨率:24 bit 输入类型:Differential 信噪比:107 dB 接口类型:SPI 工作电源电压:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-32 |
发布紧急采购，3分钟左右您将得到回复。