- 您现在的位置：买卖IC网 > PDF目录44546 > LM25066PSQX (NATIONAL SEMICONDUCTOR CORP) POWER SUPPLY SUPPORT CKT, QCC24 PDF资料下载
参数资料
| 型号： | LM25066PSQX |
| 厂商： | NATIONAL SEMICONDUCTOR CORP |
| 元件分类： | 电源管理 |
| 英文描述： | POWER SUPPLY SUPPORT CKT, QCC24 |
| 封装： | LLP-24 |
| 文件页数： | 31/48页 |
| 文件大小： | 1456K |
| 代理商： | LM25066PSQX |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页当前第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页
shown in the Telemetry and Warning Conversion Coefficients
Table.
TABLE 36. READ_AVG_IIN Register
Value
Meaning
Default
0h – 0FFFh
Average of
measured values
for current sense
voltage
0000h
MFR_SPECIFIC_15: READ_AVG_PIN (DFh)
The READ_AVG_PIN command will report the upper 12 bits
of the average VIN x IIN product as measured by the 12-bit
ADC. You will read the default value (0000h) or previous data
when the average data is not ready. This data is read with the
PMBus Read Word protocol. This register should use the
coefficients shown in the Telemetry and Warning Conversion
Coefficients Table.
TABLE 37. READ_AVG_PIN Register
Value
Meaning
Default
0h – 0FFFh
Average of
measured value
for input voltage x
input current sense
voltage
0000h
MFR_SPECIFIC_16: BLACK_BOX_READ (E0h)
The
BLACK_BOX_READ
command
retrieves
the
BLOCK_READ data which was latched in at the first assertion
of SMBA. It is re-armed with the CLEAR_FAULTS command.
It is the same format as the BLOCK_READ registers, the only
difference being that its contents are updated with the SM-
BA edge rather than the internal clock edge. This command
is read with the PMBus Block Read protocol.
MFR_SPECIFIC_17: READ_DIAGNOSTIC_WORD (E1h)
The READ_DIAGNOSTIC_WORD PMBus command will re-
port all of the LM25066 faults and warnings in a single read
operation. The standard response to the assertion of the SM-
BA signal of issuing multiple read requests to various status
registers can be replaced by a single word read to the
DIAGNOSTIC_WORD
register.
The
READ_DIAGNOSTIC_WORD command should be read with
the
PMBus
Read
Word
protocol.
The
DIAGNOSTIC_WORD is also returned in the BLOCK_READ,
BLACK_BOX_READ, and AVG_BLOCK_READ operations.
TABLE 38. READ_DIAGNOSTIC_WORD Format
Bit
Meaning
Default
15
VOUT_UNDERVOLTAGE_WARN
0
14
IIN_OP_WARN
0
13
VIN_UNDERVOLTAGE_WARN
0
12
VIN_OVERVOLTAGE_WARN
0
11
POWER GOOD
1
10
OVER_TEMPERATURE_WARN
0
9
TIMER_LATCHED_OFF
0
8
EXT_MOSFET_SHORTED
0
7
CONFIG_PRESET
1
6
DEVICE_OFF
1
5
VIN_UNDERVOLTAGE_FAULT
1
4
VIN_OVERVOLTAGE_FAULT
0
3
IIN_OC/PFET_OP_FAULT
0
2
OVER_TEMPERATURE_FAULT
0
1
CML_FAULT
0
CIRCUIT_BREAKER_FAULT
0
MFR_SPECIFIC_18: AVG_BLOCK_READ (E2h)
The AVG_BLOCK_READ command concatenates the
DIAGNOSTIC_WORD with input and output average teleme-
try information (IIN, VOUT, VIN, PIN) as well as TEMPERA-
TURE to capture all of the operating information of the part in
a single PMBus transaction. The block is 12 bytes long with
telemetry information being sent out in the same manner as
if an individual READ_AVG_XXX command had been issued
(shown below). AVG_BLOCK_READ also guarantees that
the VIN, VOUT, PIN, and IIN measurements are all time-
aligned whereas there is a chance they may not be if read
with individual PMBus commands. To read data from the
AVG_BLOCK_READ command, use the SMBus Block Read
protocol.
TABLE 39. AVG_BLOCK_READ Register Format
Byte Count (always 12)
(1 byte)
DIAGNOSTIC_WORD
(1 word)
AVG_IIN
(1 word)
AVG_VOUT
(1 word)
AVG_VIN
(1 word)
AVG_PIN
(1 word)
TEMPERATURE
(1 word)
37
www.national.com
LM25066
相关PDF资料 |
PDF描述 |
|---|---|
| LM25066PSQ | POWER SUPPLY SUPPORT CKT, QCC24 |
| LM25574Q0MT | SWITCHING REGULATOR, PDSO16 |
| LM25574Q0MTX | SWITCHING REGULATOR, PDSO16 |
| LM25576Q0MH | SWITCHING REGULATOR, PDSO20 |
| LM2574HVADJMWC | 1.8 A SWITCHING REGULATOR, 63 kHz SWITCHING FREQ-MAX, UUC |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LM25066PSQX/NOPB | 功能描述:热插拔功率分布 RoHS:否 制造商:Texas Instruments 产品:Controllers & Switches 电流限制: 电源电压-最大:7 V 电源电压-最小:- 0.3 V 工作温度范围: 功率耗散: 安装风格:SMD/SMT 封装 / 箱体:MSOP-8 封装:Tube |
| LM25069 | 制造商:NSC 制造商全称:National Semiconductor 功能描述:Positive Low Voltage Power Limiting Hot Swap Controller |
| LM25069MM-2EVAL | 功能描述:BOARD EVALUATION LM25069 RoHS:是 类别:编程器，开发系统 >> 评估演示板和套件 系列:- 标准包装:1 系列:PCI Express® (PCIe) 主要目的:接口，收发器，PCI Express 嵌入式:- 已用 IC / 零件:DS80PCI800 主要属性:- 次要属性:- 已供物品:板 |
| LM25069MM-2EVAL/NOPB | 功能描述:电源管理IC开发工具 LM25069MM-2 Eval Brd RoHS:否 制造商:Maxim Integrated 产品:Evaluation Kits 类型:Battery Management 工具用于评估:MAX17710GB 输入电压: 输出电压:1.8 V |
| LM25069PMM-1 | 制造商:NSC 制造商全称:National Semiconductor 功能描述:Positive Low Voltage Power Limiting Hot Swap Controller |
发布紧急采购，3分钟左右您将得到回复。