- 您现在的位置：买卖IC网 > PDF目录44546 > LM25066PSQX (NATIONAL SEMICONDUCTOR CORP) POWER SUPPLY SUPPORT CKT, QCC24 PDF资料下载
参数资料
| 型号： | LM25066PSQX |
| 厂商： | NATIONAL SEMICONDUCTOR CORP |
| 元件分类： | 电源管理 |
| 英文描述： | POWER SUPPLY SUPPORT CKT, QCC24 |
| 封装： | LLP-24 |
| 文件页数： | 7/48页 |
| 文件大小： | 1456K |
| 代理商： | LM25066PSQX |
第1页第2页第3页第4页第5页第6页当前第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页
STATUS_INPUT (7Ch) register, the INPUT bit in the
STATUS_WORD
(79h)
register,
and
the
IIN_OC/
PFET_OP_FAULT bit in the DIAGNOSTIC_WORD (E1h)
register will be toggled high and SMBA pin will be pulled low
unless this feature is disabled using the ALERT_MASK (D8h)
register. For proper operation, the R
S resistor value should be
less than 200 m
. Higher values may create instability in the
current limit control loop. The current limit threshold pin value
may be overridden by setting appropriate bits in the
DEVICE_SETUP register (D9h).
Circuit Breaker
If the load current increases rapidly (e.g. the load is short cir-
cuited), the current in the sense resistor (R
S) may exceed the
current limit threshold before the current limit control loop is
able to respond. If the current exceeds 1.8 or 3.6 times (user
settable) the current limit threshold, Q
1 is quickly switched off
by the 190 mA pull-down current at the GATE pin, and a Fault
Timeout Period begins. When the voltage across R
S falls be-
low the threshold the 190 mA pull-down current at the GATE
pin is switched off and the gate voltage of Q
1 is then deter-
mined by the current limit or power limit functions. If the
TIMER pin reaches 1.7V before the current limiting or power
limiting condition ceases, Q
1 is switched off by the 2 mA pull-
down current at the GATE pin as described in the Fault Timer
& Restart section. A circuit breaker event will cause the CIR-
CUIT BREAKER FAULT bit in the STATUS_MFR_SPECIFIC
(80h) and DIAGNOSTIC_WORD (E1h) registers to be tog-
gled high and SMBA pin will be pulled low unless this feature
is disabled using the ALERT_MASK (D8h) register. The cir-
cuit breaker pin configuration may be overridden by setting
appropriate bits in the DEVICE_SETUP (D9h) register.
Power Limit
An important feature of the LM25066 is the MOSFET power
limiting. The Power Limit function can be used to maintain the
maximum power dissipation of MOSFET Q
1 within the device
SOA rating. The LM25066 determines the power dissipation
in Q
1 by monitoring its drain-source voltage (SENSE to OUT),
and the drain current through R
S (VIN to SENSE). The prod-
uct of the current and voltage is compared to the power limit
threshold programmed by the resistor at the PWR pin. If the
power dissipation reaches the limiting threshold, the GATE
voltage is controlled to regulate the current in Q
1. While the
power limiting circuit is active, the fault timer is active as de-
scribed in the Fault Timer & Restart section. If the power limit
condition persists for longer than the Fault Timeout Period set
by the timer capacitor, C
T, the IIN_OC_FAULT bit in the
STATUS_INPUT (7Ch) register, the INPUT bit in the
STATUS_WORD
(79h)
register,
and
the
IIN_OC/
PFET_OP_FAULT bit in the DIAGNOSTIC_WORD (E1h)
register will be toggled high and SMBA pin will be pulled low
unless this feature is disabled using the ALERT_MASK (D8h)
register.
Fault Timer & Restart
When the current limit or power limit threshold is reached
during turn-on, or as a result of a fault condition, the gate-to-
source voltage of Q
1 is controlled to regulate the load current
and power dissipation in Q
1. When either limiting function is
active, a 90 A fault timer current source charges the external
capacitor (C
T) at the TIMER pin as shown in Figure 2 (Fault
Timeout Period). If the fault condition subsides during the
Fault Timeout Period before the TIMER pin reaches 1.7V, the
LM25066 returns to the normal operating mode and C
T is dis-
charged by the 1.9 mA current sink. If the TIMER pin reaches
1.7V during the Fault Timeout Period, Q
1 is switched off by a
2 mA pull-down current at the GATE pin. The subsequent
restart procedure then depends on the selected retry config-
uration.
If the RETRY pin is high, the LM25066 latches the GATE pin
low at the end of the Fault Timeout Period. C
T is then dis-
charged to ground by the 2.8 A fault current sink. The GATE
pin is held low by the 2 mA pull-down current until a power up
sequence is externally initiated by cycling the input voltage
(V
SYS), or momentarily pulling the UVLO/EN pin below its
threshold with an open-collector or open-drain device as
shown in Figure 3. The voltage at the TIMER pin must be
<0.3V for the restart procedure to be effective. The
TIMER_LATCHED_OFF bit in the DIAGNOSTIC_WORD
(E1h) register will remain high while the latched off condition
persists.
30115815
FIGURE 3. Latched Fault Restart Control
The LM25066 provides an automatic restart sequence which
consists of the TIMER pin cycling between 1.7V and 1V seven
times after the Fault Timeout Period, as shown in Figure 4.
The period of each cycle is determined by the 90 A charging
current, and the 2.8 A discharge current, and the value of
the capacitor C
T. When the TIMER pin reaches 0.3V during
the eighth high-to-low ramp, the 22 A current source at the
GATE pin turns on Q
1. If the fault condition is still present, the
Fault Timeout Period and the restart sequence repeat. The
RETRY pin allows selecting no retries or infinite retries. Finer
control of the retry behavior can be achieved through the
DEVICE_SETUP (D9h) register. Retry counts of 0, 1, 2, 4, 8,
16 or infinite may be selected by setting the appropriate bits
in the DEVICE_SETUP (D9h) register.
15
www.national.com
LM25066
相关PDF资料 |
PDF描述 |
|---|---|
| LM25066PSQ | POWER SUPPLY SUPPORT CKT, QCC24 |
| LM25574Q0MT | SWITCHING REGULATOR, PDSO16 |
| LM25574Q0MTX | SWITCHING REGULATOR, PDSO16 |
| LM25576Q0MH | SWITCHING REGULATOR, PDSO20 |
| LM2574HVADJMWC | 1.8 A SWITCHING REGULATOR, 63 kHz SWITCHING FREQ-MAX, UUC |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LM25066PSQX/NOPB | 功能描述:热插拔功率分布 RoHS:否 制造商:Texas Instruments 产品:Controllers & Switches 电流限制: 电源电压-最大:7 V 电源电压-最小:- 0.3 V 工作温度范围: 功率耗散: 安装风格:SMD/SMT 封装 / 箱体:MSOP-8 封装:Tube |
| LM25069 | 制造商:NSC 制造商全称:National Semiconductor 功能描述:Positive Low Voltage Power Limiting Hot Swap Controller |
| LM25069MM-2EVAL | 功能描述:BOARD EVALUATION LM25069 RoHS:是 类别:编程器，开发系统 >> 评估演示板和套件 系列:- 标准包装:1 系列:PCI Express® (PCIe) 主要目的:接口，收发器，PCI Express 嵌入式:- 已用 IC / 零件:DS80PCI800 主要属性:- 次要属性:- 已供物品:板 |
| LM25069MM-2EVAL/NOPB | 功能描述:电源管理IC开发工具 LM25069MM-2 Eval Brd RoHS:否 制造商:Maxim Integrated 产品:Evaluation Kits 类型:Battery Management 工具用于评估:MAX17710GB 输入电压: 输出电压:1.8 V |
| LM25069PMM-1 | 制造商:NSC 制造商全称:National Semiconductor 功能描述:Positive Low Voltage Power Limiting Hot Swap Controller |
发布紧急采购，3分钟左右您将得到回复。