- 您现在的位置：买卖IC网 > PDF目录14440 > LM2574DW-ADJR2G (ON Semiconductor)IC REG BUCK ADJ 0.5A 16SOICW PDF资料下载
参数资料
| 型号： | LM2574DW-ADJR2G |
| 厂商： | ON Semiconductor |
| 文件页数： | 20/26页 |
| 文件大小： | 0K |
| 描述： | IC REG BUCK ADJ 0.5A 16SOICW |
| 标准包装： | 1,000 |
| 类型： | 降压（降压） |
| 输出类型： | 可调式 |
| 输出数： | 1 |
| 输出电压： | 1.23 V ~ 37 V |
| 输入电压： | 4.75 V ~ 40 V |
| PWM 型： | 电压模式 |
| 频率 - 开关： | 52kHz |
| 电流 - 输出： | 500mA |
| 同步整流器： | 无 |
| 工作温度： | -40°C ~ 125°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 16-SOIC（0.295"，7.50mm 宽） |
| 包装： | 带卷 (TR) |
| 供应商设备封装： | 16-SOIC W |
| 其它名称： | LM2574DW-ADJR2G-ND LM2574DW-ADJR2GOSTR |
LM2574, NCV2574
The circuit in Figure 31 shows the negative boost
configuration. The input voltage in this application ranges
from ?5.0 to ?12 V and provides a regulated ?12 V output.
If the input voltage is greater than ?12 V, the output will rise
above ?12 V accordingly, but will not damage the regulator.
When a high 50 Hz or 60 Hz (100 Hz or 120 Hz
respectively) ripple voltage exists, a long delay time can
cause some problems by coupling the ripple into the
ON/OFF pin, the regulator could be switched periodically
on and off with the line (or double) frequency.
+V in
(3)
1
Feedback
C out
1000 m F
+V in
+V in
5
LM2574?XX
(12)
C in
22 m F
LM2574?12
5 (12)
4 Pwr 2 Sig 3 ON/OFF
Gnd Gnd (5)
(6) (4)
(14)
Output
7
D1
1N5817
V out = ?12 V
C in
22 m F
C1
0.1 m F
R1
47 k
3
ON/OFF 2
(5) and
4
R2
47 k
Gnds (4)
Pins and
(6)
V in
?5.0 to ?12 V
L1
330 m H
Load Current
60 mA for V in = ?5.2 V
120 mA for V in = ?7.0 V
NOTE : This picture does not show the complete circuit.
Figure 31. Negative Boost Regulator
Design Recommendations:
The same design rules as for the previous inverting
buck?boost converter can be applied. The output capacitor
C out must be chosen larger than what would be required for
a standard buck converter. Low input voltages or high output
currents require a large value output capacitor (in the range
of thousands of m F). The recommended range of inductor
values for the negative boost regulator is the same as for
inverting converter design.
Figure 32. Delayed Startup Circuitry
Undervoltage Lockout
Some applications require the regulator to remain off until
the input voltage reaches a certain threshold level. Figure 33
shows an undervoltage lockout circuit applied to a buck
regulator. A version of this circuit for buck?boost converter
is shown in Figure 34. Resistor R3 pulls the ON/OFF pin
high and keeps the regulator off until the input voltage
reaches a predetermined threshold level, which is
determined by the following expression:
) 1.0 ) R2 V
Another important point is that these negative boost
converters cannot provide any current limiting load
protection in the event of a short in the output so some other
V
th
[ V
Z1
R1
BE
(Q1)
means, such as a fuse, may be necessary to provide the load
protection.
Delayed Startup
+V in
+V in
5
LM2574?XX
(12)
There are some applications, like the inverting regulator
already mentioned above, which require a higher amount of
startup current. In such cases, if the input power source is
R1
10 k
R3
47 k
C in
22 m F
3
ON/OFF 2
(5) and
Gnds (4)
Pins and
limited, this delayed startup feature becomes very useful.
To provide a time delay between the time when the input
voltage is applied and the time when the output voltage
comes up, the circuit in Figure 32 can be used. As the input
voltage is applied, the capacitor C1 charges up, and the
voltage across the resistor R2 falls down. When the voltage
on the ON/OFF pin falls below the threshold value 1.3 V, the
regulator starts up. Resistor R1 is included to limit the
maximum voltage applied to the ON/OFF pin. It reduces the
power supply noise sensitivity, and also limits the capacitor
C1 discharge current, but its use is not mandatory.
4
Z1
1N5242B
Q1
2N3904
R2
10 k
NOTE : This picture does not show the complete circuit.
Figure 33. Undervoltage Lockout Circuit for
Buck Converter
(6)
http://onsemi.com
20
相关PDF资料 |
PDF描述 |
|---|---|
| LM2574N-3.3G | IC REG BUCK 3.3V 0.5A 8DIP |
| LQG15HN12NJ02D | INDUCTOR 12NH 300MA 0402 |
| LM2574N-ADJG | IC REG BUCK ADJ 0.5A 8DIP |
| LM2574N-12G | IC REG BUCK 12V 0.5A 8DIP |
| LQG15HN10NJ02D | INDUCTOR 10NH 300MA 0402 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LM2574HV | 制造商:NSC 制造商全称:National Semiconductor 功能描述: |
| LM2574HVM-12 | 功能描述:直流/直流开关转换器 RoHS:否 制造商:STMicroelectronics 最大输入电压:4.5 V 开关频率:1.5 MHz 输出电压:4.6 V 输出电流:250 mA 输出端数量:2 最大工作温度:+ 85 C 安装风格:SMD/SMT |
| LM2574HVM-12/NOPB | 功能描述:直流/直流开关转换器 RoHS:否 制造商:STMicroelectronics 最大输入电压:4.5 V 开关频率:1.5 MHz 输出电压:4.6 V 输出电流:250 mA 输出端数量:2 最大工作温度:+ 85 C 安装风格:SMD/SMT |
| LM2574HVM-12/NOPB | 制造商:Texas Instruments 功能描述:DC/DC Converter IC |
| LM2574HVM-15 | 功能描述:直流/直流开关转换器 RoHS:否 制造商:STMicroelectronics 最大输入电压:4.5 V 开关频率:1.5 MHz 输出电压:4.6 V 输出电流:250 mA 输出端数量:2 最大工作温度:+ 85 C 安装风格:SMD/SMT |
发布紧急采购，3分钟左右您将得到回复。