- 您现在的位置：买卖IC网 > PDF目录149393 > LM2575T-005G (ON SEMICONDUCTOR) 3.2 A SWITCHING REGULATOR, 63 kHz SWITCHING FREQ-MAX, PSFM5 PDF资料下载
参数资料
| 型号： | LM2575T-005G |
| 厂商： | ON SEMICONDUCTOR |
| 元件分类： | 稳压器 |
| 英文描述： | 3.2 A SWITCHING REGULATOR, 63 kHz SWITCHING FREQ-MAX, PSFM5 |
| 封装： | LEAD FREE, TO-220, 5 PIN |
| 文件页数： | 11/29页 |
| 文件大小： | 408K |
| 代理商： | LM2575T-005G |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页当前第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页
LM2575, NCV2575
http://onsemi.com
19
d +
ton
T +
VO
Vin
,
IQ
(quiescent current) and Vsat can be found in the
LM2575 data sheet,
Vin is minimum input voltage applied,
VO is the regulator output voltage,
ILoad is the load current.
The dynamic switching losses during turnon and
turnoff can be neglected if proper type catch diode is used.
Packages Not on a Heatsink (FreeStanding)
For a freestanding application when no heatsink is used,
the junction temperature can be determined by the following
expression:
TJ = (RqJA) (PD) + TA
where (RqJA)(PD) represents the junction temperature rise
caused by the dissipated power and TA is the maximum
ambient temperature.
Packages on a Heatsink
If the actual operating junction temperature is greater than
the selected safe operating junction temperature determined
in step 3, than a heatsink is required. The junction
temperature will be calculated as follows:
TJ = PD (RqJA + RqCS + RqSA) + TA
where RqJC is the thermal resistance junctioncase,
RqCS is the thermal resistance caseheatsink,
RqSA is the thermal resistance heatsinkambient.
If the actual operating temperature is greater than the
selected safe operating junction temperature, then a larger
heatsink is required.
Some Aspects That can Influence Thermal Design
It should be noted that the package thermal resistance and
the junction temperature rise numbers are all approximate,
and there are many factors that will affect these numbers,
such as PC board size, shape, thickness, physical position,
location, board temperature, as well as whether the
surrounding air is moving or still.
Other factors are trace width, total printed circuit copper
area, copper thickness, single or doublesided, multilayer
board, the amount of solder on the board or even color of the
traces.
The size, quantity and spacing of other components on
the board can also influence its effectiveness to dissipate
the heat.
Figure 25. Inverting BuckBoost Regulator Using the
LM257512 Develops 12 V @ 0.35 A
D1
1N5819
L1
100
mH
Output
2
4
Feedback
Unregulated
DC Input
12 V to 25 V
Cin
100
mF
/50 V
1
5
3ON/OFF
GND
+Vin
Regulated
Output
-12 V @ 0.35 A
Cout
1800
mF
/16 V
LM257512
ADDITIONAL APPLICATIONS
Inverting Regulator
An inverting buckboost regulator using the LM257512
is shown in Figure 25. This circuit converts a positive input
voltage to a negative output voltage with a common ground
by bootstrapping the regulators ground to the negative
output voltage. By grounding the feedback pin, the regulator
senses the inverted output voltage and regulates it.
In this example the LM257512 is used to generate a
12 V output. The maximum input voltage in this case
cannot exceed +28 V because the maximum voltage
appearing across the regulator is the absolute sum of the
input and output voltages and this must be limited to a
maximum of 40 V.
This circuit configuration is able to deliver approximately
0.35 A to the output when the input voltage is 12 V or higher.
At lighter loads the minimum input voltage required drops
to approximately 4.7 V, because the buckboost regulator
topology can produce an output voltage that, in its absolute
value, is either greater or less than the input voltage.
Since the switch currents in this buckboost configuration
are higher than in the standard buck converter topology, the
available output current is lower.
This type of buckboost inverting regulator can also
require a larger amount of startup input current, even for
light loads. This may overload an input power source with
a current limit less than 1.5 A.
Such an amount of input startup current is needed for at
least 2.0 ms or more. The actual time depends on the output
voltage and size of the output capacitor.
Because of the relatively high startup currents required by
this inverting regulator topology, the use of a delayed startup
or an undervoltage lockout circuit is recommended.
相关PDF资料 |
PDF描述 |
|---|---|
| LK5320-9PD0TB1 | 2-OUTPUT 150 W AC-DC PWR FACTOR CORR MODULE |
| LS1501-9EPD0T | 1-OUTPUT 100 W AC-DC REG PWR SUPPLY MODULE |
| LS1501-9EPD1T | 1-OUTPUT 100 W AC-DC REG PWR SUPPLY MODULE |
| LS1501-9ERDDT | 1-OUTPUT 100 W AC-DC REG PWR SUPPLY MODULE |
| LS2320-7ERD7T | 2-OUTPUT 100 W AC-DC REG PWR SUPPLY MODULE |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LM2575T-012 | 功能描述:直流/直流开关调节器 12V 1A Buck PWM RoHS:否 制造商:International Rectifier 最大输入电压:21 V 开关频率:1.5 MHz 输出电压:0.5 V to 0.86 V 输出电流:4 A 输出端数量: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:PQFN 4 x 5 |
| LM2575T-012G | 功能描述:直流/直流开关转换器 12V 1A Buck PWM RoHS:否 制造商:STMicroelectronics 最大输入电压:4.5 V 开关频率:1.5 MHz 输出电压:4.6 V 输出电流:250 mA 输出端数量:2 最大工作温度:+ 85 C 安装风格:SMD/SMT |
| LM2575T-015 | 功能描述:直流/直流开关调节器 15V 1A Buck PWM RoHS:否 制造商:International Rectifier 最大输入电压:21 V 开关频率:1.5 MHz 输出电压:0.5 V to 0.86 V 输出电流:4 A 输出端数量: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:PQFN 4 x 5 |
| LM2575T-015G | 制造商:ONSEMI 制造商全称:ON Semiconductor 功能描述:1.0 A, Adjustable Output Voltage, Step−Down Switching Regulator |
| LM2575T12 | 制造商:Semtech 功能描述:_ |
发布紧急采购，3分钟左右您将得到回复。