- 您现在的位置：买卖IC网 > PDF目录17413 > LM2735SD3.3EVAL (National Semiconductor)BOARD EVALUATION FOR LM2735 PDF资料下载
参数资料
| 型号： | LM2735SD3.3EVAL |
| 厂商： | National Semiconductor |
| 文件页数： | 15/58页 |
| 文件大小： | 0K |
| 描述： | BOARD EVALUATION FOR LM2735 |
| 标准包装： | 1 |
| 主要目的： | DC/DC，步升 |
| 输出及类型： | 1，非隔离 |
| 输出电压： | 3.3V |
| 电流 - 输出： | 500mA |
| 输入电压： | 3 ~ 5.5 V |
| 稳压器拓扑结构： | 升压 |
| 频率 - 开关： | 1.6MHz |
| 板类型： | 完全填充 |
| 已供物品： | 板 |
| 已用 IC / 零件： | LM2735 |
| 相关产品： | LM2735YSDX-ND - IC REG BOOST SEPIC ADJ 2.1A 6LLP LM2735YMYX-ND - IC REG BST SEPIC ADJ 2.1A 8EMSOP LM2735YMFX-ND - IC REG BOOST SEPIC ADJ SOT23-5 LM2735XSDX-ND - IC REG BOOST SEPIC ADJ 2.1A 6LLP LM2735XMYX-ND - IC REG BST SEPIC ADJ 2.1A 8EMSOP LM2735XMFX-ND - IC REG BOOST SEPIC ADJ SOT23-5 LM2735YSDDKR-ND - IC REG BOOST SEPIC ADJ 2.1A 6LLP LM2735YMYDKR-ND - IC REG BST SEPIC ADJ 2.1A 8EMSOP LM2735YMFDKR-ND - IC REG BOOST SEPIC ADJ SOT23-5 LM2735XSDDKR-ND - IC REG BOOST SEPIC ADJ 2.1A 6LLP 更多... |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页当前第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页
V FB
R 2
V O
C 3
R LOAD
SNVS485F – JUNE 2007 – REVISED APRIL 2013
R 1
Figure 25. Setting External Pole-Zero
F ZERO - CF =
1
2 S ( R 2 x C 3 )
(14)
There is an associated pole with the zero that was created in the above equation.
F POLE - CF =
1
2 S ((R 1 R 2 ) x C 3 )
(15)
It is always higher in frequency than the zero.
A right-half plane zero (RHPZ) is inherent to all boost converters. One must remember that the gain associated
with a right-half plane zero increases at 20dB per decade, but the phase decreases by 45° per decade. For most
applications there is little concern with the RHPZ due to the fact that the frequency at which it shows up is well
beyond crossover, and has little to no effect on loop stability. One must be concerned with this condition for large
inductor values and high output currents.
( D ' ) R Load
RHP ZERO =
2
2 S x L
(16)
There are miscellaneous poles and zeros associated with parasitics internal to the LM2735, external
components, and the PCB. They are located well over the crossover frequency, and for simplicity are not
discussed.
PCB Layout Considerations
When planning layout there are a few things to consider when trying to achieve a clean, regulated output. The
most important consideration when completing a Boost Converter layout is the close coupling of the GND
connections of the C OUT capacitor and the LM2735 PGND pin. The GND ends should be close to one another
and be connected to the GND plane with at least two through-holes. There should be a continuous ground plane
on the bottom layer of a two-layer board except under the switching node island. The FB pin is a high impedance
node and care should be taken to make the FB trace short to avoid noise pickup and inaccurate regulation. The
feedback resistors should be placed as close as possible to the IC, with the AGND of R1 placed as close as
possible to the GND (pin 5 for the WSON) of the IC. The V OUT trace to R2 should be routed away from the
inductor and any other traces that are switching. High AC currents flow through the V IN , SW and V OUT traces, so
they should be as short and wide as possible. However, making the traces wide increases radiated noise, so the
designer must make this trade-off. Radiated noise can be decreased by choosing a shielded inductor. The
remaining components should also be placed as close as possible to the IC. Please see Application Note AN-
1229 SNVA054 for further considerations and the LM2735 demo board as an example of a four-layer layout.
Copyright ? 2007–2013, Texas Instruments Incorporated
Product Folder Links: LM2735
15
相关PDF资料 |
PDF描述 |
|---|---|
| RB-0505D/P | CONV DC/DC 1W 5VIN +/-05VOUT |
| IPS1051LTRPBF | IC IPS SW LOW SIDE 1CH SOT-223 |
| A9CCA-0404E | FLEX CABLE - AFK04A/AE04/AFK04A |
| A9CAA-1005E | FLEX CABLE - AFK10A/AE10/AFH10T |
| A9CCG-0208F | FLEX CABLE - AFG02G/AF02/AFG02G |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LM2735XMF | 制造商:NSC 制造商全称:National Semiconductor 功能描述:520kHz/1.6MHz - Space-Efficient Boost and SEPIC DC-DC Regulator |
| LM2735XMF/NOPB | 功能描述:直流/直流开关调节器 SPACE-EFF BOOST AND SEPIC DC-DC REG RoHS:否 制造商:International Rectifier 最大输入电压:21 V 开关频率:1.5 MHz 输出电压:0.5 V to 0.86 V 输出电流:4 A 输出端数量: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:PQFN 4 x 5 |
| LM2735XMF/NOPB | 制造商:Texas Instruments 功能描述:DC/DC Converter IC |
| LM2735XMFEVAL | 功能描述:BOARD DEMO FOR LM2735 SOT23-5 RoHS:是 类别:编程器，开发系统 >> 评估板 - DC/DC 与 AC/DC（离线）SMPS 系列:- 产品培训模块:Obsolescence Mitigation Program 标准包装:1 系列:True Shutdown™ 主要目的:DC/DC，步升 输出及类型:1，非隔离 功率 - 输出:- 输出电压:- 电流 - 输出:1A 输入电压:2.5 V ~ 5.5 V 稳压器拓扑结构:升压 频率 - 开关:3MHz 板类型:完全填充 已供物品:板 已用 IC / 零件:MAX8969 |
| LM2735XMFEVAL/NOPB | 功能描述:电源管理IC开发工具 LM2735XMF EVAL BOARD RoHS:否 制造商:Maxim Integrated 产品:Evaluation Kits 类型:Battery Management 工具用于评估:MAX17710GB 输入电压: 输出电压:1.8 V |
发布紧急采购，3分钟左右您将得到回复。