参数资料
| 型号： | LM311DR2 |
| 厂商： | ON Semiconductor |
| 文件页数： | 7/9页 |
| 文件大小： | 0K |
| 描述： | IC COMPARATOR SGL HI VOLT 8SOIC |
| 产品变化通告： | Product Obsolescence 14/Apr/2010 |
| 标准包装： | 1 |
| 类型： | 通用 |
| 元件数： | 1 |
| 输出类型： | DTL，MOS，开路集电极，开路发射极，RTL，TTL |
| 电压 - 电源，单路/双路(±)： | 5 V ~ 30 V，±2.5 V ~ 15 V |
| 电流 - 静态（最大值）： | 7.5mA |
| 封装/外壳： | 8-SOIC（0.154"，3.90mm 宽） |
| 安装类型： | 表面贴装 |
| 包装： | 剪切带 (CT) |
| 其它名称： | LM311DR2OSCT |
LM211, LM311
http://onsemi.com
7
TECHNIQUES FOR AVOIDING OSCILLATIONS IN COMPARATOR APPLICATIONS
When a high speed comparator such as the LM211 is used
with high speed input signals and low source impedances,
the output response will normally be fast and stable,
providing the power supplies have been bypassed (with
0.1
mF disc capacitors), and that the output signal is routed
well away from the inputs (Pins 2 and 3) and also away from
Pins 5 and 6.
However, when the input signal is a voltage ramp or a slow
sine wave, or if the signal source impedance is high (1.0 k
W
to 100 k
W), the comparator may burst into oscillation near
the crossingpoint. This is due to the high gain and wide
bandwidth of comparators like the LM211 series. To avoid
oscillation or instability in such a usage, several precautions
are recommended, as shown in Figure 16.
The trim pins (Pins 5 and 6) act as unwanted auxiliary
inputs. If these pins are not connected to a trimpot, they
should be shorted together. If they are connected to a
trimpot, a 0.01
mF capacitor (C1) between Pins 5 and 6 will
minimize the susceptibility to AC coupling. A smaller
capacitor is used if Pin 5 is used for positive feedback as in
Figure 16. For the fastest response time, tie both balance pins
to VCC.
Certain sources will produce a cleaner comparator output
waveform if a 100 pF to 1000 pF capacitor (C2) is connected
directly across the input pins. When the signal source is
applied through a resistive network, R1, it is usually
advantageous to choose R2 of the same value, both for DC
and for dynamic (AC) considerations. Carbon, tinoxide,
and metalfilm resistors have all been used with good results
in comparator input circuitry, but inductive wirewound
resistors should be avoided.
When comparator circuits use input resistors (e.g.,
summing resistors), their value and placement are particularly
important. In all cases the body of the resistor should be close
to the device or socket. In other words, there should be a very
short lead length or printedcircuit foil run between
comparator and resistor to radiate or pick up signals. The
same applies to capacitors, pots, etc. For example, if R1 =
10 k
W, as little as 5 inches of lead between the resistors and
the input pins can result in oscillations that are very hard to
dampen. Twisting these input leads tightly is the best
alternative to placing resistors close to the comparator.
Since feedback to almost any pin of a comparator can
result in oscillation, the printedcircuit layout should be
engineered thoughtfully. Preferably there should be a
groundplane under the LM211 circuitry (e.g., one side of a
double layer printed circuit board). Ground, positive supply
or negative supply foil should extend between the output and
the inputs to act as a guard. The foil connections for the
inputs should be as small and compact as possible, and
should be essentially surrounded by ground foil on all sides
to guard against capacitive coupling from any fast
highlevel signals (such as the output). If Pins 5 and 6 are not
used, they should be shorted together. If they are connected
to a trimpot, the trimpot should be located no more than
a few inches away from the LM211, and a 0.01
mF capacitor
should be installed across Pins 5 and 6. If this capacitor
cannot be used, a shielding printedcircuit foil may be
advisable between Pins 6 and 7. The power supply bypass
capacitors should be located within a couple inches of the
LM211.
A standard procedure is to add hysteresis to a comparator
to prevent oscillation, and to avoid excessive noise on the
output. In the circuit of Figure 17, the feedback resistor of
510 k
W from the output to the positive input will cause about
3.0 mV of hysteresis. However, if R2 is larger than 100
W,
such as 50 k
W, it would not be practical to simply increase
the value of the positive feedback resistor proportionally
above 510 k
W to maintain the same amount of hysteresis.
When both inputs of the LM211 are connected to active
signals, or if a highimpedance signal is driving the positive
input of the LM211 so that positive feedback would be
disruptive, the circuit of Figure 16 is ideal. The positive
feedback is applied to Pin 5 (one of the offset adjustment
pins). This will be sufficient to cause 1.0 mV to 2.0 mV
hysteresis and sharp transitions with input triangle waves
from a few Hz to hundreds of kHz. The positivefeedback
signal across the 82
W resistor swings 240 mV below the
positive supply. This signal is centered around the nominal
voltage at Pin 5, so this feedback does not add to the offset
voltage of the comparator. As much as 8.0 mV of offset
voltage can be trimmed out, using the 5.0 k
W pot and 3.0 kW
resistor as shown.
相关PDF资料 |
PDF描述 |
|---|---|
| LM319M | IC COMPARATOR DUAL HS 14-SOP |
| LM3302N | IC COMPARATOR QUAD 14-DIP |
| LM339DR | IC COMPARATOR QUAD GP 8SOIC |
| LM392DR2G | IC OP AMP/COMPARATOR LP 8-SOIC |
| LM393TLX | IC COMPARATOR DUAL 8USMD |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LM311DR2G | 功能描述:校验器 IC 5-30V SGL Comparator Commercial Temp RoHS:否 制造商:STMicroelectronics 产品: 比较器类型: 通道数量: 输出类型:Push-Pull 电源电压-最大:5.5 V 电源电压-最小:1.1 V 补偿电压（最大值）:6 mV 电源电流（最大值）:1350 nA 响应时间: 最大工作温度:+ 125 C 安装风格:SMD/SMT 封装 / 箱体:SC-70-5 封装:Reel |
| LM311DR2G-CUT TAPE | 制造商:ON 功能描述:LM Series 36 V 300 nA Surface Mount Single Comparator - SOIC-8 |
| LM311DRE4 | 功能描述:校验器 IC Single Strobed Differential RoHS:否 制造商:STMicroelectronics 产品: 比较器类型: 通道数量: 输出类型:Push-Pull 电源电压-最大:5.5 V 电源电压-最小:1.1 V 补偿电压（最大值）:6 mV 电源电流（最大值）:1350 nA 响应时间: 最大工作温度:+ 125 C 安装风格:SMD/SMT 封装 / 箱体:SC-70-5 封装:Reel |
| LM311DRG4 | 功能描述:校验器 IC Single Strobed Differential RoHS:否 制造商:STMicroelectronics 产品: 比较器类型: 通道数量: 输出类型:Push-Pull 电源电压-最大:5.5 V 电源电压-最小:1.1 V 补偿电压（最大值）:6 mV 电源电流（最大值）:1350 nA 响应时间: 最大工作温度:+ 125 C 安装风格:SMD/SMT 封装 / 箱体:SC-70-5 封装:Reel |
| LM311DT | 功能描述:校验器 IC Single GP Voltage RoHS:否 制造商:STMicroelectronics 产品: 比较器类型: 通道数量: 输出类型:Push-Pull 电源电压-最大:5.5 V 电源电压-最小:1.1 V 补偿电压（最大值）:6 mV 电源电流（最大值）:1350 nA 响应时间: 最大工作温度:+ 125 C 安装风格:SMD/SMT 封装 / 箱体:SC-70-5 封装:Reel |
发布紧急采购，3分钟左右您将得到回复。