- 您现在的位置：买卖IC网 > PDF目录1820 > LM3495MTCX/NOPB (National Semiconductor)IC REG BUCK SYNC ADJ 10A 16TSSOP PDF资料下载
参数资料
| 型号： | LM3495MTCX/NOPB |
| 厂商： | National Semiconductor |
| 文件页数： | 22/36页 |
| 文件大小： | 0K |
| 描述： | IC REG BUCK SYNC ADJ 10A 16TSSOP |
| 标准包装： | 1 |
| 系列： | PowerWise® |
| 类型： | 降压（降压） |
| 输出类型： | 可调式 |
| 输出数： | 1 |
| 输出电压： | 0.6 V ~ 5.5 V |
| 输入电压： | 2.9 V ~ 18 V |
| PWM 型： | 电流模式，混合 |
| 频率 - 开关： | 200kHz ~ 1.5MHz |
| 电流 - 输出： | 10A |
| 同步整流器： | 是 |
| 工作温度： | -40°C ~ 125°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 16-TSSOP（0.173"，4.40mm 宽） |
| 包装： | 标准包装 |
| 供应商设备封装： | 16-TSSOP |
| 产品目录页面： | 1300 (CN2011-ZH PDF) |
| 配用： | LM3495EVAL-ND - BOARD EVALUATION LM3495 |
| 其它名称： | LM3495MTCXDKR |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页当前第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页
SNVS410F – FEBRUARY 2006 – REVISED APRIL 2013
VLIN5 DECOUPLING CAPACITOR
The VLIN5 pin should always be decoupled with a 2.2 μF, 10V-rated ceramic capacitor placed as close as
possible to the VLIN5 and PGND pins of the LM3495. The decoupling capacitor should have a minimum X5R or
X7R type dielectric to ensure that the capacitance remains stable over the expected voltage and temperature
range.
INPUT CAPACITOR
The input capacitors to a buck regulator are used to smooth the large current pulses drawn by the inductor and
load when the high-side FET is on. Due to this large AC stress, input capacitors are usually selected on the basis
of their AC rms current rating rather than bulk capacitance. Low ESR is beneficial because it reduces the power
dissipation in the capacitors. Although any of the capacitor types mentioned in the OUTPUT CAPACITOR
section can be used, MLCCs are common because of their low ESR and because in general the input to a buck
converter does not require as much bulk capacitance as the output. Input current, I rms , can be calculated using
the following equation:
I rms = I O x D(1 - D)
(22)
A good estimate for the maximum AC rms current is one-half of the maximum load current. For this example, the
rms input current can be estimated as 3.5A. Regardless of the type and number of capacitors used, every design
will benefit from the addition of a 0.1 μF to 1 μF ceramic capacitor placed as close as possible to the drain of the
high-side FET and the source of the low-side FET.
In most applications for POL power supplies, the input voltage is the output of another switching converter. This
output often has a lot of bulk capacitance. One 22 μF MLCC provides enough local smoothing and keeps the
input impedance high enough to prevent power supply interaction from the source. For switching power supplies,
the minimum quality dielectric that should be used is X5R. The preferred capacitor voltage rating for a 12V input
voltage is 25V, due to the drop-off in capacitance of MLCCs under a DC bias. Capacitors with a 16V rating can
still be used if size and cost are limiting factors. For this example the current rating of each of the capacitors
should be at least 3Arms. The ESR of large-value ceramic caps is usually below 10 m ? , which keeps the heating
to a minimum.
CURRENT LIMIT
For this design, the trip point for the current limit circuitry should be below the peak current rating of the output
inductor, which is 18A. To account for the tolerance of the internal current source, the change in the R DSON of the
low-side FET, and to prevent excessive heating of the inductor, a target of 15A has been chosen. A 3.8A margin
exists between the expected 11.2A peak current and the current limit threshold to allow for line and load
transients. Following the equation from the Applications Information section the value used for R LIM should be
3.32 k ? 1%.
CONTROL LOOP COMPENSATION
The LM3495 uses emulated peak current-mode PWM control to correct changes in output voltage due to line and
load transients. This unique architecture combines the fast line transient response of peak current mode control
with the ability to regulate at very low duty cycles. As a further advantage, the small signal characteristics of
emulated peak current mode control are almost identical to those of traditional peak current mode control, and
hence compensation can be selected using nearly identical calculations.
The control loop is comprised of two parts. The first is the power stage, which consists of the duty cycle
modulator, output filter, and the load. The second part is the error amplifier, which is a transconductance (g M )
amplifier with a typical transconductance of 750 μmho and a typical output impedance of 72 M ? . Figure 36
shows the regulator and voltage control loop components.
22
Product Folder Links: LM3495
Copyright ? 2006–2013, Texas Instruments Incorporated
相关PDF资料 |
PDF描述 |
|---|---|
| LM350T | IC REG LDO ADJ 3A TO220AB |
| LM350T | IC REG LDO ADJ 3A TO220-3 |
| LM3686TLE-AAED/NOPB | IC REG BUCK SYNC .9A TRPL 12USMD |
| LM399AH | IC VREF SHUNT PREC 6.95V TO-46-4 |
| LM4040A25IDBZT | IC VREF SHUNT PREC 2.5V SOT23-3 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LM3497M/NOPB | 制造商:Texas Instruments 功能描述:IC LED DRIVER 制造商:Texas Instruments 功能描述:POWER REGULATOR/CONTROLLER IC |
| LM3497MM/NOPB | 功能描述:板上安装温度传感器 RoHS:否 制造商:Omron Electronics 输出类型:Digital 配置: 准确性:+/- 1.5 C, +/- 3 C 温度阈值: 数字输出 - 总线接口:2-Wire, I2C, SMBus 电源电压-最大:5.5 V 电源电压-最小:4.5 V 最大工作温度:+ 50 C 最小工作温度:0 C 关闭: 安装风格: 封装 / 箱体: 设备功能:Temperature and Humidity Sensor |
| LM3497MMX/NOPB | 功能描述:板上安装温度传感器 RoHS:否 制造商:Omron Electronics 输出类型:Digital 配置: 准确性:+/- 1.5 C, +/- 3 C 温度阈值: 数字输出 - 总线接口:2-Wire, I2C, SMBus 电源电压-最大:5.5 V 电源电压-最小:4.5 V 最大工作温度:+ 50 C 最小工作温度:0 C 关闭: 安装风格: 封装 / 箱体: 设备功能:Temperature and Humidity Sensor |
| LM3497MX/NOPB | 制造商:Texas Instruments 功能描述:IC LED DRIVER 制造商:Texas Instruments 功能描述:POWER REGULATOR/CONTROLLER IC |
| LM349J | 制造商:未知厂家 制造商全称:未知厂家 功能描述:Voltage-Feedback Operational Amplifier |
发布紧急采购，3分钟左右您将得到回复。