参数资料
型号: LM75AD,112
厂商: NXP Semiconductors
文件页数: 9/24页
文件大小: 137K
描述: IC TEMP SENSOR DIGITAL 8-SOIC
特色产品: NXP - I2C Interface
标准包装: 100
功能: 温度监视系统(传感器),监视器
传感器类型: 内部
感应温度: -55°C ~ 125°C
精确度: ±3°C(最小值)
拓扑: ADC(三角积分型),比较器,振荡器,寄存器库
输出类型: 2 线串行,I²C?
输出警报:
输出风扇:
电源电压: 2.8 V ~ 5.5 V
工作温度: -55°C ~ 125°C
安装类型: 表面贴装
封装/外壳: 8-SOIC(0.154",3.90mm 宽)
供应商设备封装: 8-SO
包装: 管件
产品目录页面: 846 (CN2011-ZH PDF)
配用: 568-4002-ND - DEMO BOARD I2C
其它名称: 568-4226-5
935269775112
LM75AD
LM75AD-ND
LM75A_4
?NXP B.V. 2007. All rights reserved.
Product data sheet
Rev. 04  10 July 2007
9 of 24
NXP Semiconductors
LM75A
Digital temperature sensor and thermal watchdog
When a set-point register is read, all 16 bits are provided to the bus and must be collected
by the controller to complete the bus operation. However, only the 9 most signicant bits
should be used and the 7 LSB of the LSByte are equal to zero and should be ignored.
T
ab
le
13 shows examples of the limit data and value.
7.5  OS output and polarity
The OS output is an open-drain output and its state represents results of the device
watchdog operation as described in
Section
7.1. In order to observe this output state, an
external pull-up resistor is needed. The resistor should be as large as possible, up to
200 k&, to minimize the Temp reading error due to internal heating by the high OS sinking
current.
The OS output active state can be selected as HIGH or LOW by programming bit B2
(OS_POL) of register Conf: setting bit OS_POL to logic 1 selects OS active HIGH and
setting bit B2 to logic 0 sets OS active LOW. At power-up, bit OS_POL is equal to logic 0
and the OS active state is LOW.
7.6  OS comparator and interrupt modes
As described in
Section
7.1, the device OS output responds to the result of the
comparison between register Temp data and the programmed limits, in registers Tos and
Thyst, in different ways depending on the selected OS mode: OS comparator or
OS interrupt. The OS mode is selected by programming bit B1 (OS_COMP_INT) of
register Conf: setting bit OS_COMP_INT to logic 1 selects the OS interrupt mode, and
setting to logic 0 selects the OS comparator mode. At power-up, bit OS_COMP_INT is
equal to logic 0 and the OS comparator is selected.
Table 11.   Tos register
MSByte
LSByte
7    6
5
4
3
2
1
0
7
6
5
4
3
2
1
0
D8    D7    D6    D5    D4    D3    D2    D1    D0
X
X
X
X
X
X
X
Table 12.   Thyst register
MSByte
LSByte
7
6
5
4
3
2
1
0
7
6
5
4
3
2
1
0
D8    D7    D6    D5    D4    D3    D2    D1    D0
X
X
X
X
X
X
X
Table 13.   Tos and Thyst limit data and value
11-bit binary
(2s complement)
Hexadecimal value
Decimal value
Value
0 1111 1010
0FA
250
+125.0 癈
0 0011 0010
032
50
+25.0 癈
0 0000 0001
001
1
+0.5 癈
0 0000 0000
000
0
0.0 癈
1 1111 1111
1FF
1
0.5 癈
1 1100 1110
1CE
50
25.0 癈
1 1001 0010
192
110
55.0 癈
相关PDF资料
PDF描述
LM75BD,112 IC TEMP SENSOR DIGITAL 8-SOIC
LM75BIMX-5+ IC TEMP SENSOR WATCHDOG 8SOIC
LM92CIMX/NOPB IC SENSOR TEMP/THERM COMP 8-SOIC
LT1123CST#TRPBF IC REG CTRLR SGL 5V SOT223
LT1248IS#PBF IC PFC CTRLR AVERAGE CURR 16SOIC
相关代理商/技术参数
参数描述
LM75ADP 制造商:NXP Semiconductors 功能描述:Digital Temp Sensor 2-Wire,LM75ADP
LM75ADP,118 功能描述:板上安装温度传感器 TEMP SENSOR DIGITAL RoHS:否 制造商:Omron Electronics 输出类型:Digital 配置: 准确性:+/- 1.5 C, +/- 3 C 温度阈值: 数字输出 - 总线接口:2-Wire, I2C, SMBus 电源电压-最大:5.5 V 电源电压-最小:4.5 V 最大工作温度:+ 50 C 最小工作温度:0 C 关闭: 安装风格: 封装 / 箱体: 设备功能:Temperature and Humidity Sensor
LM75ADP,118 制造商:NXP Semiconductors 功能描述:IC, TEMP SENSOR, 0.125C, 3C, TSSOP-8
LM75ADP,118-CUT TAPE 制造商:NXP 功能描述:LM75A Series SMD 5.5 mA Digital Temperature Sensor w/ Thermal Watchdog TSSOP-8
LM75ADP/DG,118 功能描述:板上安装温度传感器 DIGITAL TEMP SENSOR AND THERMAL WATCHDOG RoHS:否 制造商:Omron Electronics 输出类型:Digital 配置: 准确性:+/- 1.5 C, +/- 3 C 温度阈值: 数字输出 - 总线接口:2-Wire, I2C, SMBus 电源电压-最大:5.5 V 电源电压-最小:4.5 V 最大工作温度:+ 50 C 最小工作温度:0 C 关闭: 安装风格: 封装 / 箱体: 设备功能:Temperature and Humidity Sensor