- 您现在的位置：买卖IC网 > PDF目录32307 > LM8500IMT9/NOPB (NATIONAL SEMICONDUCTOR CORP) SPECIALTY CONSUMER CIRCUIT, PDSO48 PDF资料下载
参数资料
| 型号： | LM8500IMT9/NOPB |
| 厂商： | NATIONAL SEMICONDUCTOR CORP |
| 元件分类： | 消费家电 |
| 英文描述： | SPECIALTY CONSUMER CIRCUIT, PDSO48 |
| 封装： | TSSOP-48 |
| 文件页数： | 20/20页 |
| 文件大小： | 327K |
| 代理商： | LM8500IMT9/NOPB |
9.0 Functional Description (Continued)
LED — Optional LED output. When the controller is oper-
ating in normal (non power save) mode, a low is output to the
pin. When the controller is in power save mode, a high is
output to the pin.
RESET — Reset pin. When pulled low, a manual reset is
executed. For normal operation, this pin must be pulled high.
Under no circumstances should the pin be left floating.
UART_TX — UART transmit pin. The signal is inverted for
use with standard RS-232 drivers.
UART_RX — UART receive pin. The signal is inverted for
use with standard RS-232 drivers.
DTR — Data Terminal Ready signal for the UART. If a high
level is detected on the pin, this signals that the UART is not
ready. If a low level is detected on the pin, this signals that
the UART is ready.
WD_Out — Watch dog output. For correct operation, this
pin should be connected to the RESET pin.
OSC_OUT — Clock oscillator output pin.
OSC_IN — Clock oscillator input pin
GND — Digital Ground
AGND — Analog ground
DV
CC — Digital power supply.
AV
CC — Analog power supply. For best performance, this
pin should be connected to a filter.
Users of the LLP package are cautioned to be aware that the
central metal area and the pin 1 index mark on the bottom of
the package may be connected to GND. See figure below:
9.3 USART FRAMING FORMAT
The device communicates with the touch screen driver using
the UART set at a baud rate of 38400, 8, n, 1.
All communication from the host software and the controller
consists of a command byte and occasionally data byte(s). If
data byte(s) follow a command byte, it must be sent directly
after the command byte. If the device is in the power save
mode, a delay must be inserted between the wake up com-
mand and the command byte. Refer to the Power Save
mode section for more details. For every command byte sent
to the controller, an acknowledge byte is sent back and
sometimes data byte(s).
A command byte is distinguished by having the 7th bit of the
command byte set (1). If any data byte(s) is to follow, the 7th
bit of the data byte is reset (0).
Data packets sent to the host software can be either four or
five bytes in length. If the pressure measurement is enabled,
five bytes are sent. If the pressure measurement is not
enabled, four bytes are sent.
The first byte of each data packet is a header byte. This
header byte is used to synchronize and differentiate between
four or five byte packages. If a four byte data package is
sent, the 4th bit of the header byte is reset (0). If a five byte
data package is sent, the 4th bit of the header byte is set (1).
The 6th bit of the second byte of the data packet is used to
indicate the touch state. If the bit is set (1), then a touchdown
or continuous touch is detected. If the bit is reset (0), then a
liftoff is detected.
9.3.1 Data packet format table
Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0
Byte 1
1
0
L
0
Byte 2
0
S
X
2
X
1
X
0
Y
2
Y
1
Y
0
Byte 3
0
X
9
X
8
X
7
X
6
X
5
X
4
X
3
Byte 4
0
Y
9
Y
8
Y
7
Y
6
Y
5
Y
4
Y
3
Byte 5
0
Z
6
Z
5
Z
4
Z
3
Z
2
Z
1
Z
0
L - Package length. (0 = 4 bytes,1=5 bytes)
S - Touch state (0 = liftoff, 1 = touchdown or continuous
touch)
X
X - X position (10 bit value)
Y
Y - Y position (10 bit value)
Z
Z - Z positon (7 bit value), this byte is only transmitted if the
pressure measurement is enabled
9.3.2 Command Bytes
PC
Command
PC
Byte
1
PC
Byte 2
TSC
Byte 1
TSC
Byte 2
Read
clock-speed
(3,33MHz,
10MHz)
$B0
$CA
$00, $01
Read
parameters
$B1
$CA
Read
software
version
number
$B2
$C7
Read # of
calibration
points
$B3
$CA
$00, $02,
$05, $0D
20037216
FIGURE 1. LLP Package Bottom View
LM8300/LM8500
www.national.com
9
相关PDF资料 |
PDF描述 |
|---|---|
| LM8500HLQ9/NOPB | SPECIALTY CONSUMER CIRCUIT, QCC44 |
| LM8300HVA9/NOPB | SPECIALTY CONSUMER CIRCUIT, PQCC44 |
| LM8300IMT9/NOPB | SPECIALTY CONSUMER CIRCUIT, PDSO48 |
| LM8300HLQ9/NOPB | SPECIALTY CONSUMER CIRCUIT, QCC44 |
| LMF501T-2 | AM, AUDIO SINGLE CHIP RECEIVER, PBCY3 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LM8500IVA9 | 制造商:NSC 制造商全称:National Semiconductor 功能描述:Four Wire Resistive Touchscreen Controller with Brownout |
| LM8500-REF-01 | 功能描述:显示开发工具 LM8500 DEV KIT RoHS:否 制造商:4D Systems 产品:4Display Shields 工具用于评估:?OLED-160-G1, ?OLED-160-G2 接口类型:Serial 工作电源电压:5 V |
| LM8502 | 制造商:TI 制造商全称:Texas Instruments 功能描述:Intelligent Lighting Management Unit That Fuses a 1.2A Dual High-Side Flash LED Driver with a 10-Output Low-Side LED Driver |
| LM8502TME | 制造商:TI 制造商全称:Texas Instruments 功能描述:Intelligent Lighting Management Unit That Fuses a 1.2A Dual High-Side Flash LED Driver with a 10-Output Low-Side LED Driver |
| LM8502TME/NOPB | 功能描述:LED照明驱动器 RoHS:否 制造商:STMicroelectronics 输入电压:11.5 V to 23 V 工作频率: 最大电源电流:1.7 mA 输出电流: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:SO-16N |
发布紧急采购，3分钟左右您将得到回复。