- 您现在的位置：买卖IC网 > PDF目录32307 > LM8500IMT9/NOPB (NATIONAL SEMICONDUCTOR CORP) SPECIALTY CONSUMER CIRCUIT, PDSO48 PDF资料下载
参数资料
| 型号： | LM8500IMT9/NOPB |
| 厂商： | NATIONAL SEMICONDUCTOR CORP |
| 元件分类： | 消费家电 |
| 英文描述： | SPECIALTY CONSUMER CIRCUIT, PDSO48 |
| 封装： | TSSOP-48 |
| 文件页数： | 9/20页 |
| 文件大小： | 327K |
| 代理商： | LM8500IMT9/NOPB |
14.0 Calibration (Continued)
14.2 CALIBRATION PROCEDURES WITH
COORDINATES CHECKING ENABLED
To do TS calibration with coordinates checking enabled, first
ensure the Calibration Coordinates Checking is enabled on
the device. This can be accomplished by sending a com-
mand byte of $B1 (Read Parameters command) and check-
ing the 5th bit of the 12th reply byte is set. Alternatively, if the
device is set to Calibration Coordinates Checking enabled
as default, this step can be skipped.
The TS driver sends the command byte to do calibration
($BD). The TS driver should wait for the reply bytes and
ensure it is the same command bytes it sent. The device
waits for a touch to be detected on the panel. Once a touch
is detected, the device checks it against the predetermined
calibration values as noted on Table 3. Two Points Calibra-
Points Calibration. If the detected touch is within the pre-
defined value (±127 of the raw A/D value), the device will
send a command of $C4 to the TS driver and store the
calibration point in the internal flash. The TS driver can now
send a command byte to do the next calibration point. If the
detected touch is not within the predefined value, the device
will send a reply byte of $C8 to the TS driver. Upon receiving
this reply byte, the TS driver can resend the calibration
command for the same calibration point, go the next calibra-
tion point, or abort the calibration process.
Once all the calibration points are done, the device does a
self-test. If the self-test was not successful, the device will
20037210
FIGURE 8. Calibration Procedures with Coordinates Checking Enabled
LM8300/LM8500
www.national.com
17
相关PDF资料 |
PDF描述 |
|---|---|
| LM8500HLQ9/NOPB | SPECIALTY CONSUMER CIRCUIT, QCC44 |
| LM8300HVA9/NOPB | SPECIALTY CONSUMER CIRCUIT, PQCC44 |
| LM8300IMT9/NOPB | SPECIALTY CONSUMER CIRCUIT, PDSO48 |
| LM8300HLQ9/NOPB | SPECIALTY CONSUMER CIRCUIT, QCC44 |
| LMF501T-2 | AM, AUDIO SINGLE CHIP RECEIVER, PBCY3 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LM8500IVA9 | 制造商:NSC 制造商全称:National Semiconductor 功能描述:Four Wire Resistive Touchscreen Controller with Brownout |
| LM8500-REF-01 | 功能描述:显示开发工具 LM8500 DEV KIT RoHS:否 制造商:4D Systems 产品:4Display Shields 工具用于评估:?OLED-160-G1, ?OLED-160-G2 接口类型:Serial 工作电源电压:5 V |
| LM8502 | 制造商:TI 制造商全称:Texas Instruments 功能描述:Intelligent Lighting Management Unit That Fuses a 1.2A Dual High-Side Flash LED Driver with a 10-Output Low-Side LED Driver |
| LM8502TME | 制造商:TI 制造商全称:Texas Instruments 功能描述:Intelligent Lighting Management Unit That Fuses a 1.2A Dual High-Side Flash LED Driver with a 10-Output Low-Side LED Driver |
| LM8502TME/NOPB | 功能描述:LED照明驱动器 RoHS:否 制造商:STMicroelectronics 输入电压:11.5 V to 23 V 工作频率: 最大电源电流:1.7 mA 输出电流: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:SO-16N |
发布紧急采购，3分钟左右您将得到回复。