参数资料
| 型号： | LNK501P |
| 厂商： | Power Integrations |
| 文件页数： | 9/20页 |
| 文件大小： | 0K |
| 描述： | IC SWIT OCP CV/CC HV 8DIP |
| 标准包装： | 3,000 |
| 系列： | LinkSwitch® |
| 输出隔离： | 隔离 |
| 频率范围： | 26kHz ~ 46kHz |
| 输出电压： | 700V |
| 功率（瓦特）： | 4W |
| 工作温度： | -40°C ~ 150°C |
| 封装/外壳： | 8-DIP（0.300"，7.62mm），7 引线 |
| 供应商设备封装： | DIP-8B |
| 包装： | 管件 |
| 配用： | 596-1001-ND - KIT DESIGN ACCELERATOR ADAPTER |
LNK501
At very light or no-load, typically less than 2 mA of output current,
the output voltage rises due to leakage inductance peak charging
of the secondary. This voltage rise can be reduced with a small
preload with little change to no-load power consumption.
The output voltage load variation can be improved across the
whole load range by adding an optocoupler and secondary
reference (Figure 6). The secondary reference is designed to only
provide feedback above the normal peak power point voltage
to maintain the correct constant current characteristic.
Component Selection
The schematic shown in Figure 5 outlines the key components
needed for a LinkSwitch supply.
Clamp diode – D1
Diode D1 should be either a fast (t rr <250 ns) or ultra-fast
type (t rr <50 ns), with a voltage rating of 600 V or higher. Fast
recovery types are preferred, being typically lower cost. Slow
diodes are not recommended; they can allow excessive DRAIN
ringing and the LinkSwitch to be reverse biased.
Clamp Capacitor – C2
Capacitor C2 should be a 0.1 μ F, 100 V capacitor. Low cost
metallized plastic ?lm types are recommended. The tolerance
of this part has a very minor effect on the output characteristic
so any of the standard ±5%, ±10% or ±20% tolerances are
acceptable. Ceramic capacitors are not recommended. The
common dielectrics used such as Y5U or Z5U are not stable
with voltage or temperature and may cause output instability.
Ceramic capacitors with high stability dielectrics may be used
but are expensive compared to metallized ?lm types.
CONTROL Pin Capacitor – C1
Capacitor C1 is used during start-up to power LinkSwitch and
sets the auto-restart frequency. For designs that have a battery
load this component should have a value of 0.22 μ F and for
resistive loads a value of 1 μ F. This ensures there is suf?cient
time during start-up for the output voltage to reach regulation.
Any capacitor type is acceptable with a voltage rating of
10 V or above.
Feedback Resistor – R1
The value of R1 is selected to give a feedback current into the
CONTROL pin of approximately 2.3 mA at the peak output
power point of the supply. The actual value depends on the V OR
selected during design. Any 1%, 0.25 W resistor is suitable.
Output Diode – D2
Either PN fast, PN ultra-fast or Schottky diodes can be used
depending on the ef?ciency target for the supply, Schottky
diodes giving higher ef?ciency then PN diodes. The diode
voltage rating should be suf?cient to withstand the output
voltage plus the input voltage transformed through the turns
ratio (a typical V OR of 50 V requires a diode PIV of 50 V).
Slow recovery diodes are not recommended (1N400X types).
Output Capacitor – C4
Capacitor C4 should be selected such that its voltage and ripple
current speci?cations are not exceeded.
LinkSwitch Layout considerations
Primary Side Connections
Since the SOURCE pins in a LinkSwitch supply are switching
nodes, the copper area connected to SOURCE together with C1,
C2 and R1 (Figure 5) should be minimized, within the thermal
contraints of the design, to reduce EMI coupling.
The CONTROL pin capacitor C1 should be located as close as
possible to the SOURCE and CONTROL pins.
To minimize EMI coupling from the switching nodes on the
primary to both the secondary and AC input, the LinkSwitch
should be positioned away from the secondary of the transformer
and AC input.
Routing the primary return trace from the transformer primary
around LinkSwitch and associated components further reduces
coupling.
Y capacitor
If a Y capacitor is required, it should be connected close to the
transformer secondary output return pin(s) and the primary bulk
capacitor negative return. Such placement will maximize the
EMI bene?t of the Y capacitor and avoid problems in common-
mode surge testing.
Quick Design Checklist
As with any power supply design, all LinkSwitch designs
should be veri?ed on the bench to make sure that component
speci?cations are not exceeded under worst case conditions.
Note: In a LinkSwitch circuit, the SOURCE is a switching
node. This should be taken into consideration during testing.
Oscilloscope measurements should be made with probe grounded
to DC voltages such as primary return or DC rail but not to
SOURCE. Power supply input voltage should always be supplied
using an isolation transformer. The following minimum set of
tests is strongly recommended:
1. Maximum drain voltage – Verify that V DS does not exceed
675 V at highest input voltage and peak output power.
2. Maximum drain current – At maximum ambient temperature,
maximum input voltage and peak output power, verify drain
current waveforms at start-up for any signs of transformer
saturation and excessive leading edge current spikes.
LinkSwitch has a minimum leading edge blanking time of
I
2/05
9
相关PDF资料 |
PDF描述 |
|---|---|
| LNK584GG | IC OFFLINE SWITCHER 3W 8-SMD |
| LOC110S | OPTOCOUPLER TRANSISTOR 8-SMD |
| LOC111S | OPTOCOUPLER TRANSISTOR 8-SMD |
| LOC112S | OPTOCOUPLER TRANSISTOR 8-SMD |
| LP2950ACDT-3.3RG | IC REG LDO 3.3V .1A DPAK |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LNK501P_1 | 制造商:POWERINT 制造商全称:Power Integrations, Inc. 功能描述:2.2W Cell Phone Charger |
| LNK501PN | 功能描述:交流/直流开关转换器 3W 85-265 VAC 4W 230 VAC RoHS:否 制造商:STMicroelectronics 输出电压:800 V 输入/电源电压（最大值）:23.5 V 输入/电源电压（最小值）:11.5 V 开关频率:115 kHz 电源电流:1.6 mA 工作温度范围:- 40 C to + 150 C 安装风格:SMD/SMT 封装 / 箱体:SSO-10 封装:Reel |
| LNK520 | 制造商:POWERINT 制造商全称:Power Integrations, Inc. 功能描述:Energy Efficient, CV or CV/CC Switcher for Very Low Cost Adapters and Chargers |
| LNK520G | 功能描述:IC SWIT OCP CV/CC HV 8SMD RoHS:否 类别:集成电路 (IC) >> PMIC - AC-DC 转换器，离线开关 系列:LinkSwitch® 标准包装:1 系列:FPS™ 输出隔离:隔离 频率范围:61kHz ~ 73kHz 输入电压:8 V ~ 26 V 输出电压:650V 功率（瓦特）:12W 工作温度:-40°C ~ 115°C 封装/外壳:8-DIP（0.300"，7.62mm） 供应商设备封装:8-MDIP 包装:Digi-Reel® 其它名称:FSL206MRBNFSDKR |
| LNK520GN | 功能描述:交流/直流开关转换器 3W 85-265 VAC 4W 230 VAC RoHS:否 制造商:STMicroelectronics 输出电压:800 V 输入/电源电压（最大值）:23.5 V 输入/电源电压（最小值）:11.5 V 开关频率:115 kHz 电源电流:1.6 mA 工作温度范围:- 40 C to + 150 C 安装风格:SMD/SMT 封装 / 箱体:SSO-10 封装:Reel |
发布紧急采购，3分钟左右您将得到回复。